RK38G*J1 Hotpoint Wall Oven - Instructions

First I turned the Breaker off for the Oven. I removed the two screws that hold the element/cover plate. I pulled the element out to get access to wires attached to element & removed screws holding wires to element. I reversed the process to put back together.

The repair was fairly easy. Removed the 2 screws that hold the plate to the oven and then pulled out the element and loosen up the screws that connect it. Installed the new element and re-attached the element to the plate and secured the plate back to the oven. This site was very easy to use and very helpful and I will use it again if I need another part.

Shut off the power at the circuit breaker, removed the two nuts holding the element to the oven, unscrewed the two screws connected to the wire leads, removed the bad element and reversed the process to replace with the new one.

After supper, without biscuits, I removed the element by simply removing 4 screws with my nut driver. We went home and I immediately went online to your web site, inserted the old element part number, followed the ordering instructions, and in 3 dayd the new element had been delivered to our door. Several days later we were invited to mom's for dinner once again. I quickly installed the new element (perfect fit and works great) and enjoyed a great supper........with biscuits this time. Thank you.

First observed the situation to determine if I should try and repair. I decided I could and should. Got the element and proceeded. I first turned the power off at the circuit breaker to cut the electrical power to the stove then I removed the two screws that holds the unit in place and then pulled unit out to where I could see the wire connection; removed the two screws on the wire connection and replaced the old element with the new element. reinserted the unit back into position and replaced the two screws that holds the unit in the stove. Turned power back on and tested the oven for any problems. Stove is working great.

Unplugged stove, removed front door, carefully removed two screws holding the cover plate of the element. Gently pulled the element out about 3-4 inches removed the two screw attaching the electrical wires to the element , making sure the wires did not pull back into the stove. Removed old element, attached new element to the electrical wires with the new screws received with the new element. Carefully pushed the wires and element back into place making sure the insulation was also in place. Re-attached the cover plate with the two screws I had removed. Plugged the stove back in and tested the element. Replaced the front door .... job complete!

Just wanted to add that the part came in two days, super mailing time, thanks!!

I removed the 2 screws and the 2 wires from the broken heating element. I removed the broken oven heating element. Then I attached the 2 wires to the new heating element and put the 2 screws in to attach the new heating element into the oven. The new oven heating element worked just fine and I was done.

First I turned off the circuit breaker leading to the oven. Then I removed the two screws that held the old element in place. I pulled out the element and disconnected the wires. I reconnected the wires to the new element and pushed it back in place. I then secured it with the two screws. I turned the circuit breaker back on and turned on the oven. Works just great!!!

Removed two socket head screws form inside oven rear wall. Pulled element out and disconnected two screws attaching wiring. Replaced with new.

remove screws attaching burner plate to back of oven, pull out element, undo wiring to old burner by unscrewing 2 screws, remove old burner, reverse process to put new burner in

First I read the already posted repair stories to give me confidence I could perform the repair.
Followed their steps -
Removed the two screws holding the plate to the oven.
Pulled out the element.
Removed the two screws holding the wires to the element.
Installed the new element by attaching the two screws (which were supplied) to the element.
Reinstalled the plate to the oven.
Tested it and it worked perfectly saving a costly service call.

It was so easy. Just removed the cover and then unscrewed the wires (keep track of which wires go to which side). Do teh reverse to reinstall

Repair was as easy as one, two three. Turned off the power and removed the two screws holding the element in place. Then pulled the element out approx. 3 inches and removed the two screws connecting the wires to the element.

From there I reversed the process and the repair was complete in less then 5 minutes, and I am not a electrician.

Just like your example said/turn the power off to the oven/remove the screws that hold the element in place and then I pulled th element out a little ways and disconnected the wires/reconnecting took a little longer only because it was hard to see/but I connected the two wires and put the screws back in and it worked. Saved me a lot of money/my husband wanted to get a new double oven

This was extremely easy to replace. When I told my mom I would replace it for her, she thought I was crazy. When she saw how easy it was, she finally understood. I had to remove the two screws holding the element in place. I pulled it out about 3 inches and unscrewed one screw for one wire. I didn't want to lose the wire, so I immediately connected the wire to the new element. I disconnected the second wire and attached it to the new bake element. Then attached the two screws putting the plate back up, securing the element. So easy! Just unscrewing and replacing 4 screws and I was done!! Took less than 10 minutes. I didn't have any real tools available, so I used a small adjustable wrench and it worked fine. The best part was it was so easy we were able to have a working oven in time for Thanksgiving!