Models > RGB746HED3WH > Instructions

RGB746HED3WH Hotpoint Range - Instructions

All installation instructions for RGB746HED3WH parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RGB746HED3WH
286-300 of 310
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

it would glow, but it wouldn,t light

  • Customer: Robert from New Hope, MN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I took out the bottom broiler drawer and reached to the back of the oven. i loosened the screws,unplugged it and replaced the igniter and plugged it in and put it all together and it works great now.

My stove would not light at all.

  • Customer: Jajuan from Kansas City, MO
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
It was easy I unplugged the stove but I left the gas alone. I used a flat head screw driver to take the oven sheet off. Then I unscrewed the oven lighter and the bracket holding it. Then I disconnected it and put the new one on. The hard part was letting the wd-40 dissolve for the rusty screws

No Spark

  • Customer: Milo from Plainfield, IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
The instructions were to unscrew the top, and lift. It was very difficult to do, just to see that the part to change was not there. It was in the back of the range. Oh Well.

Replaced damaged oven rack

  • Customer: Vicki from Irvine, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I ordered the oven rack on a Tuesday and received it the very next day - was wowed at the service.

Medal Burners

  • Customer: Vicente from Joliet, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I have had my medal burners for 5 years and with young adults cooking I could not seem to get them cleaned. They had the part that I needed and now I have a whole new top stove. Thank you

Gas oven would not ignite

  • Customer: Russell from Maple Shade, NJ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Using your information that was posted i order the part that was most likely the problem. The video was spot on for the replace part.

Fails to maintain set temp.

  • Customer: Ronald from Arkport, NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
watch the video. Do the repair. What could be easier. Bake some cookies just for a test.. I did it twice just to be sure. Thank you partselect. Rite part, rite price, fast shipping, arrived next day...............

oven would not light,upon looking at igniter,I could see it was not glowing with attempted startup.

  • Customer: Richard from Cornish, NH
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
viewed your video(which was my exact model)saw where everything was and how to access it and in no time was up and running again.

Left side front and back burner would not light

  • Customer: Eric from Arlington, MA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I located the spark module at back of top panel and I switched the wires of one of the other burners to the burner that wasn't lighting. By doing that I found that part of the module wasn't operating properly.

no problem to report

  • Customer: michael from spanaway, WA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
followed instructions

Burner Spark Module burned out needed a replacement

  • Customer: Nancy from Las Vegas, NV
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
My husband did the repair so it was very easy for me, as well as for him, he found the bad part from your parts diagram which was a great help, he changed it out in no time and so we were both very Happy. Thank you for your help. Nancy & David

No heat on main oven burner

  • Customer: FADI from Rancho Cordova, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
10 minute job, remove racks, 2 screw to take out the lower oven deck, 2 bolts removed for the igniter, unplug the connector, install the new igniter, re-add the 2 bolts & your done. Re install the lower deck, put the racks back on, plug the oven back in, turned on bake, set to 400, within 45 secs, the igniter kicked in and my oven was back in action. Contacted GE and they wanted $99 for inspection, $75.00 for the part (2x the current cost) + labor for 1 hours $90, overall costs if i had GE or a contractor = 250-300.00, total costs for me 43.00+ plus 15 mins of labor. I truly saved using a few you tube videos and with parts select, i got a OEM part shipped fast! Thank you all.

The oven would not light. The igniter glowed red but the gas never turned on.

  • Customer: James from Tucson, AZ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
My first guess was that the igniter was good because it glowed red. After viewing your repair video and reading your text "hints" which told me that even if the igniter turned red it may still be the problem I decided to get the igniter. Installation was simple. First shut off the gas. I have a gas turn-off near the range. Then I removed the metal panel on my right side and had to remove the cover over the wire hole in the rear panel and squeeze the igniter connector through the that hole in order to free the igniter wires. I then removed the 2 screws holding the igniter onto the burner. I then installed the new igniter by running the wires, plugging the connector together and pushing it back through the wire hole so that the connector was behind the rear panel. Then put the wire cover back on, 1 screw, then attach the igniter to the burner, 2 screws, then remount the metal panel, 1 screw. Time to test: Turned on the gas and set the oven for 300 (just where I wanted to set it for the test).The new igniter glowed much brighter than the old had glowed and soon on came the gas lighting for an expression of success. Thank you all for the help...

Oven would not heat to proper temperature

  • Customer: William from Fredericksburg, VA
  • Difficulty: Very Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Wrench set
  • 0 of 0 people found this instruction helpful
Because of the location of the nuts for the igniter which were under the heating unit it was very difficult to get a wrench or any tool under it in order to undo them. I had to purchase a 1/4 inch box wrench, as I did not have one, only an open end, in order to make it easier to affix the wrench to the nut. There was not enough room to get any other tool under there and I could only get a i/4 turn each time I tried to loosen it. Finally after about 4 hours I got both nuts loosened. I then had to apply glue to the end of my finger in order to get the nut back into position to attach the new igniter. Then of course it was back to the 1/4 turns. After finally getting both nuts screwed in I then found that the new igniter had a male clip on the end as did the old attahment. So, I had to splice the wires in order to connect the new to the old clip. Finally after around 6 hours the job was complete and the new igniter did its job. The oven now heats to the proper temperature. My knees are still sore from being on them for all that time.

Oven Would Not Heat To Indicated Temperature.

  • Customer: Scott from ARLINGTON, IA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
This repair is just straight forward switching out the parts. The new part was constructed slightly different in regards the placement of the four connecting tabs but they are marked pretty clearly. The issue I had was after everything was put back together. I turned on the oven and the preheated indicator beep and light immediately came on. . . Before the oven ever turned on the igniter. I thought perhaps I'd installed the large, white connector on the circuit board backwards and unplugged it (w/o unplugging the power). It only goes on one way. I plugged it back in, tried it again and viola, it works perfectly now. One other note: the old oven control knob would not fit the new shaft, so I had to get a new knob. The old control shaft was plastic and twice the diameter of the new, metal one.
All Instructions for the RGB746HED3WH
286-300 of 310