Models > RGB532BEA2WH

RGB532BEA2WH Hotpoint Range - Overview

Get Parts and Repair Help for RGB532BEA2WH

If you know the range repair part you need, you can browse the list of all parts on the RGB532BEA2WH, or you can search by name or part description. You can also find your part by where it is located on the RGB532BEA2WH by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. We’ve also included any installation videos we have for RGB532BEA2WH parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$2.82

Light Bulb - 40W

Sold individually.

$38.36

Flat Style Oven Igniter Kit

The flat style gas oven igniter included in this kit has a body length of 3-3/4". This kit comes with a mounting bracket and a wire connector with a plug. *Please note: the connector plug might need to be removed and spliced to range wiring using porcelain wire nuts. This part is used to heat your oven.

$9.62

Door Handle End Cap

This oven door handle end cap is used on both the left and right hand sides. Sold individually.

$2.14

Grate Bumper - Black

Sold individually.

$39.65

Oven Rack

Sold individually.

$23.27

Surface Burner Spark Electrode

This part helps your burner ignite and produce flame.

$108.07

Oven Thermostat

This part establishes and maintains the internal temperature of the oven cavity.

$35.14

Oven Door Gasket with Mounting Clips

$5.55

Oven Light Socket - With Push In Receptacle

$2.36

SCREW

Sold Individually.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

oven would not light or keep temp.

  • Customer: zack from corning CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set, Wrench set
  • 382 of 383 people found this instruction helpful
first I thought it was a faulty gas valve, so I pulled it out, started researching for a replacement part, found your site and started research. I discovered thhat the igniter was the culprit, that info. saved me about a week of time and a 100 bucks, so I installed the gas safety valve back in the oven, patience is the word for the day, you cross thread thi... read more

Oven wouldn't heat. This degraded over several weeks.

  • Customer: Durwood from Suffield CT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 242 of 313 people found this instruction helpful
1. Pulled the 110V power plug. It was not necessary to turn off the gas; just be careful not to stretch or pinch the flexhose behind the stove.
2. Removed the oven door by opening a couple of inches then lifting upward.
3. Removed the warming drawer by pulling out to the stop, then pushing the small levers on the side of the track to release.
read more

Oven not getting hot/no flame no gas.

  • Customer: Guadalupe from Stockton CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 82 of 86 people found this instruction helpful
Step 1. Pull oven out disconnect power,turn off gas & remove gas line from stove.
Step 2. Remove broiler drawer,locate igniter & safety valve.
Step 3. Disconnect 2pin molex connector for igniter and faston connectors from
valve.
Step 4. Use nut driver remove fasteners that hold igniter and valve remove gas line and feed
from valve.read more