Models > RF368LXMS0 > Instructions

RF368LXMS0 Whirlpool Range - Instructions

All installation instructions for RF368LXMS0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RF368LXMS0
46-60 of 178
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Lower Door Trim gets rusty

  • Customer: James.O from Newark DE
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 3 of 3 people found this instruction helpful
I have removed this piece once before and painted it,
but it is difficult to prepare surface.

I tried to replace the part without removing the door
but had difficulty getting the screws to line up.

So, I took the door off. Forgot that you are supposed to jam
the spring hinges in the open position before you remove the door. Manual describes how to do this but picture is not very helpful. So I made two wooden dowels about 3/8" in dia by about 3/4" long. Opened the hinge with a screwdriver and jammed the dowels in place.

Door Trim went on easily and the oven door went back on quickly.

Surprised they don't make this trim piece with rust proof material.

The oven was blowing a circuit.

  • Customer: Rhonda from Logan OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 5 of 9 people found this instruction helpful
Unplugged unit from wall.
Unscrewed the two screws on at he back of the oven where the element is attached
Removed old element by pulling apart the connectors.
Attached new element to the connectors.
Replaced cover with the two screws.

Broke glass door on stove while cleaning it

  • Customer: Aires from Canton GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 8 of 18 people found this instruction helpful
I'm still unsure why it broke ,but it was just a matter of removing two screws that hold the handle in place and sliding in the glass...

Oven Door Locked

  • Customer: Grace from Beavercreek OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 5 of 9 people found this instruction helpful
Unplugged, took off back, removed old part, put on new part and connected. Replugged and it worked great.

Fire Damaged Control Board and Panel

  • Customer: Brad from Miami FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 6 of 13 people found this instruction helpful
A range top grease fire destroyed the control board and blackened the contol panel on my Whirlpool range/oven. Both replacement parts came within 3 days and the repair was pretty straightforward. I removed the back panel, diconnected all wiring connectors to the control board, range conrol rheostats and LED indicator lights, and removed the blackened control panel. The replacement parts fit perfectly and the entire reassembly took less than 30 minutes. The oven/range looks brand new and the entire repair cost less than $400. Thanks Parts Select.

Burner Element did not work

  • Customer: Paul from Reedsburg WI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 4 of 7 people found this instruction helpful
Shut off breaker. Remove a total of 3 screws attach wires, replace screws, turn breaker on. Done!

Top burner would not turn off at any time.

  • Customer: Donald from Byron MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 4 of 7 people found this instruction helpful
Unpluged range for safety (power earlier removed by circuit breaker turnoff).
Removed two screws from front switch cover.
Removed knob from effected switch and removed the wires on the back of the switch.
Removed two screws holding switch and removed switch.
Reversed the process to install new switch.
The entire project took about ten minutes.

broken bottom drawer glide and missing rivet on drawer front panel

  • Customer: David from Fairborn OH
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
Removed the old, broken drawer glide by removing the Phillips head screw. Then placed the new glide into place and fastened with the existing screw.

The rivet on the top of the bottom drawer front was missing. I lined up the drawer front with the supporting bracket behind it and inserted the rivet. All you have to do is tap the top of the pin in the center of the rivet to lock it in place. No rivet tool is needed. That should be explained in the parts listing because I bought the rivet tool before I realized I didn't need it.

Bake element was taking time to warm up

  • Customer: Jean-Claude from Miami FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 4 people found this instruction helpful
Wire connection was damaged, replaced end piece

Oven heating irradically.

  • Customer: Ruth from Oregon IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 5 people found this instruction helpful
This did not solve the problem. Since we were still under warranty we called the store where we bought the appliance and they are sending a repairman next week. We even ordered a sensor and installed that too but that didn't help.

Must be in the circuit board or something. We'll see. Thanks anyway

broken face plate holder on the bottom drawer of my stove

  • Customer: Alma from Chicago IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
It was very easy just two screws. The easiest thing was ordering the part. Your company had a good schematic of my appliance so it made it very easy to get the correct part.
Thank you

Control panel on stove needed to be replaced

  • Customer: Sherry from Saint Cloud FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 11 people found this instruction helpful
Opened the back of the stove, unplugged the wires from the damaged panel, inserted the wires in the new panel, replaced the panel and back of stove. The plug-ins were located differently than the old panel, and two wires were identical - hope I plugged them in the right slots.

Bottom drawer

  • Customer: Eric from Saint Michael MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 5 people found this instruction helpful
It was easy to find the part. I ordered it on Sunday and it arrived Wednesday. A stress-free experience.

The switch on the door broke. This prevented my oven from cleaning and the light burned all the time so I had to unscrew it.

  • Customer: PAM from DALHART TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 5 people found this instruction helpful
First I removed the two screws that hold the glass cook top in place. Then I removed 4 screws that hold a small metal plate that shields the switch. Replacing the switch was very simply just a matter of unplugging four wire connectors from the old switch, sliding the new one in and reconnecting the wires. It was very easy to find the part on the website. I just located the switch on the diagram and ordered the part. I really surprised my husband that I ordered the part and repaired the stove by myself. He was intending on calling a repairman, but I did it myself.

Oven door was distroyed and dirty from previous owner

  • Customer: Alejandro from West Palm Beach FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 12 of 32 people found this instruction helpful
I dismounted the oven door following the graphic templates that this site has for that model. Then I replaced the gasquet (seal window), appliying an apoxic glue to hold it on place. Then I started to put it togueter, from the bottom to the top, first the lower trim, I screwed it back to the metal frame, then the left and right trims, it goes tied by pressing it to the sides, after that I installed the top and screwed it to the frame. It holded all toguether cery well. My oven looks like new now.
All Instructions for the RF368LXMS0
46-60 of 178