Quick Question!

Have you ever purchased from PartSelect.com before?

Models > RF368LXMS0 > Instructions

RF368LXMS0 Whirlpool Range - Instructions

All installation instructions for RF368LXMS0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RF368LXMS0
16-30 of 178
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

8" Burner element intermittent, unable to control.

  • Customer: Charles from Enfield, CT
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 18 of 21 people found this instruction helpful
Easy.... UNPLUG THE STOVE FROM THE 240 VOLT OUTLET & READ THE DIRECTIONS THAT COME WITH THE NEW PART !! Removed upper rear cover panel 8 screws & removed panel, removed knob & 2 screws from front of control unit (on the control panel), pulled the control off the panel from the rear, removed the wires on the rear of control & connected them to the SAME terminals on the new control (one at a time). Then installed the new control by reversing the procedure above. Took about 15 minutes. IMPORTANT HINTS: 1) Make sure you save the little black pressure clip from the control stem on the new control, if you need to break-off the little part at the end of the stem. You will need to push the clip back into the recess on the new stem, in order for the knob to stay on the stem when you put it back on; 2) Use a needle-nose plier to pull the wire clips from the old control terminals & push them onto the same terminals on the new control, one at a time so the wiring is correct.

Burner was not heating up

  • Customer: Gary from Hellertown, PA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 21 of 32 people found this instruction helpful
Puled out the electical plug . Removed the back panel. Pulled off the switch knob. Removed the 2 screws holding the switch. Took the wires off of the old switch and placed them on the corespondig connector on the new switch. Put everything back in reverse order.

Scratches in Surface

  • Customer: Michelle from Richardson, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 20 of 29 people found this instruction helpful
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

Lower element went out

  • Customer: Kimberly from Palestine, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 16 of 19 people found this instruction helpful
I removed the two screws that held the element in place . I think pulled out the element and disconnected the two wires. I put the new element in and connected the two wires. I went to put the element back in and something sparked and burned up the wire. Lesson learned - turn the electricity off first. I had to pay a repair man to come out and replace the wire.

Oven light not working

  • Customer: Carol from Allison Park, PA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 17 of 23 people found this instruction helpful
I turned off the breaker (I'm a little nervous even unplugging a 220 plug). I first removed the cover from the back of the stove to get to the wiring/socket. Removed the two wires from the leads - they just pull off by hand but use a needlenose pilers if it is stuck. One is larger so no need to try to remember which one goes where. I removed the glass cover and bulb from inside the oven. I read another post on this site that said there were clips that you had to press to get the old socket out which helped. That part was a little tricky as the insulation around the socket makes it hard to see and the opening is really tight. I finally found the clips and pressed one then got that side out enough to hold the clip back then pressed the other clip and I was able to push it right out. I did not have the strength to press both clips with enough pressure but if you do, that would probably be easier. From inside the oven, I pushed the new socket through the hole - there was a little notch in the opening that had to match up with the socket. I had to push pretty firmly until I felt both clips snap in place. Replaced the wires, turned on the power, screwed in the bulb and cover and I had light!

bought floor model with loose cord that melted block terminal

  • Customer: larry from alexandria, IN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 14 of 15 people found this instruction helpful
Safety first always shut breaker off at box.
I unplugged stove, disconnected wires keeping in mind the color placement. Unscrewed one ground screw and removed terminal block. Attached new block with ground screw, replaced wires in correct order, re-attached plug. Then reattached safety cover. Pretty simple for d.i.y.

1 Of 4 Electric Burner Would Not Heat.

  • Customer: Hollie from Virginia Beach, VA
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set
  • 17 of 25 people found this instruction helpful
To fix our whirlpool electric range burner, I followed the following steps: 1. Read the owner's manual and parts list. 2. Disassemble and inspect to determine cause - bad burner or bad switch. 3. Order replacement switch on line from partselect, and wait for delivery. 4. Replace and test. Switch appeared to be mechanically defective in that it would not rotate freely, and would not turn on affected burner. 5. A. Obtained return instructions from partselect and mailed return to part select on may 9, 2008. At this writing (may 16th) nothing heard from partselect. 5. B. Concurrently, visited local appliance shop and purchased another replacement switch. 6. Installed and tested 2nd replacement switch. Test results satisfactory. 7. Returned the range to full normal service. To make this repair from start to finish, including time awaiting receipt of parts ordered from smartselect - 5 days. At this writing (16 may) I have not heard from smartselect regarding credit for the return of the defective swithch. Hollie tiedemann - virginia beach, va

Broken door handle

  • Customer: Ed from North Palm Beach, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 15 of 19 people found this instruction helpful
Part came super fast, remove and replace two screws - nothing to it

Oven doesn't heat evenly

  • Customer: Helen from Brush, CO
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 18 of 30 people found this instruction helpful
Moved the stove out from the wall. Took out the screws from the back and then from the top. I pulled the piece through the back to unplug the clips from the elements. But the wires went back through the openings. So I had to take the back off of the stove to get to the wires to put back through the holes in the stove. Once the clips were back together, I put the back back on the stove. Rebolted the part to the stove and moved it back.

someone did not install cord properly! they left a strong strain on one of the 3 wires, with a loose nut connection that caused it to heat and melt the plastic that poped out toward the rear metal cover and short circuited.

  • Customer: Richard from Daytona Beach, AL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 14 of 19 people found this instruction helpful
I cut the ends of the cord and went with direct wire (no round eye clip) to the back side of the terminal block and tightened firmly. It took about 20 Minutes.

Burned Out Termincal Block

  • Customer: Jeffrey from Davie, FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 12 of 14 people found this instruction helpful
I discoverd my switch box locked with my stove electrical port and stove stopped functioning. Pulled my stove back and saw that the "terminal block" was melted on one side; hence, switch box locked in place to avoid a fire, thank goodness. Looked up part on internet, unplugged stove, took off terminal box, ordered part and replaced. BTW - PART SELECT is awesome; I received my part the very next day!!! :-) Very happy with their service.

None

  • Customer: Richard Finneman from Muskegon, MI
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 11 of 12 people found this instruction helpful
Turned off power.Removed 2 screws, flipped top over, removed old element, replaced new element,turned over top,fasten down with 2 screws.Turned on power. Turned on burner,made coffee-took a brake.

missing screws for oven door

  • Customer: donna from baltimore, MD
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 10 of 12 people found this instruction helpful
After searching on the internet for a very long time, we were almost ready to order the screws "blind" (no picture) from Sears for almost $10.oo per screw. Then I stumbled onto this website and found exactly what I was looking for, with a detailed description AND a picture!! Not to mention a price that was two thirds less than Sears..for TWO screws. Now the oven door is secure and we are no longer on our search for the right screws.

Lighting hit my house and blew the computer board out, the stove top work but oven would not, replacing this part fixed my oven!! $200, compared to replacing for $600. Thanks!

  • Customer: Laura from Chipley, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 9 of 10 people found this instruction helpful
took back of stove off ,total 6 screws, unpluged blown computer 3 plugs, pluged in new!

Shattered outer oven door glass

  • Customer: Frederick from La Grange, IL
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 12 of 19 people found this instruction helpful
We removed the door from oven assembly and laying it flat on the bench removed the stainless steel cover from the rest of the door. Removing the shattered pieces of safety glass was done heating and scraping off vinyl tape.(difficult.)Caution! Do not allow any pieces of glass get under the stainless steel cover, it will leave ugly scratches! We purchased double sided vinyl tape 1/2" wide, 1/16" thick and aluminum "Flue tape" (600 deg. F) 1 1/2" wide from local hardware store to replace the original ones in their previous location. Fitting the new glass on sticky tape has to be done accurately. (no problem). Assembling it was little tricky but still within the ability of a do-it-selfers. We wondered if we should not put the rough side of the glass facing in or out. The original was with the smooth side out so that what we did. If any additional scraping of accumulated grease is needed especially on the inside glass, it requires more disassembly, but we would strongly suggest doing it (we did), while it is all opened. To our surprise the glass arrived by Fed Ex within 24 hours of ordering and now our Whirlpool is gleaming like new again. The cost of this product with shipping/handling by PartsSelect was much lower than ordering it from the other "original" source. Thank you! Sincerely Fred T.
All Instructions for the RF368LXMS0
16-30 of 178