Models > RF362LXSS0 > Instructions

RF362LXSS0 Whirlpool Range - Instructions

All installation instructions for RF362LXSS0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RF362LXSS0
46-60 of 127
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broken Rear Drawer Glide

  • Customer: Ed from Maple Grove MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
This was a very smooth repair. In total it took about 5 minutes. The pot drawer below the oven wasn't gliding like it once did. After I replaced the glides it works like new. Please note, if you are going to replace one side go the next step and replace both to provide balance to the drawer.

light bulb went out in my oven

  • Customer: Janet from Ada MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 4 people found this instruction helpful
My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.

Broiler element not working

  • Customer: Normand from Lincoln RI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 3 of 7 people found this instruction helpful
It went great. I am not very handy, but with a little help from your website reviews, I was able to easily remove the old broiler element and replace it with the new one in less than an hour. I immediately tested it and found that it worked great.

Broken handle

  • Customer: Derek from Middleport NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 4 people found this instruction helpful
Simple removed two screws pulled old one off installed new.

Bad Element

  • Customer: Dean from Farmington NY
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 4 people found this instruction helpful
Remove top by opening oven and taking out two screws in the front. Lift up top and unplug wire connectors on bad element, writing down where they are landed. Take out screw on element bracket and replace. That easy. Be sure to unplug appliance for your safety. :-) Also just wanted to add that PartSelect was great. Ordered it on saturday and was cooking with it on tuesday. Great job.

oven light burnt out

  • Customer: William from Schwenksville PA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 7 people found this instruction helpful
1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

baking element non operational

  • Customer: GARY from JACKSON WY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
removed two screws to faceplate at rear of oven. Disconntected contact wires, installed bake element reconnected contact wires, attached faceplate turned on oven holy hell it works just saved some money on service call thanks!!!

Oven light would not work--faulty socket

  • Customer: Delores from Warren MN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 2 of 4 people found this instruction helpful
After removing the back of the stove, the old light socket was fairly easy to remove. The new socket slipped in place and the wires reattached and now the oven has a light again. A very simple process--especially for someone who's not an expert in repairing appliances.

Broke glass door on stove while cleaning it

  • Customer: Aires from Canton GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 11 people found this instruction helpful
I'm still unsure why it broke ,but it was just a matter of removing two screws that hold the handle in place and sliding in the glass...

Both outside door handles turned very beige

  • Customer: Howard from Boynton Beach FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 4 of 11 people found this instruction helpful
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Broken rear stove drawer glide

  • Customer: John from Maysville GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Removed drawer, after removing the 50# of junk in the drawer, Used screw driver to remove screw that holds glide to drawer and then place new part into place put screw into hole and tightened screw. Replaced drawer and told wife not to put 50# of junk back into the drawer.

The heating coil was no longer working.

  • Customer: Amanda from Midwest City OK
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
My husband pulled the oven out and unscrewed the screws(in the back) the heating element came right out. He did everything on his own. The only thing he needed a little help with was for me to keep the heating coil flush to the back wall of the oven, while he screwed the new one in. It was a very quick job. The longest part was pulling the oven out to get behind it and sliding it back in.

Shattered outer oven door glass

  • Customer: Frederick from La Grange IL
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 2 of 6 people found this instruction helpful
We removed the door from oven assembly and laying it flat on the bench removed the stainless steel cover from the rest of the door. Removing the shattered pieces of safety glass was done heating and scraping off vinyl tape.(difficult.)Caution! Do not allow any pieces of glass get under the stainless steel cover, it will leave ugly scratches! We purchased double sided vinyl tape 1/2" wide, 1/16" thick and aluminum "Flue tape" (600 deg. F) 1 1/2" wide from local hardware store to replace the original ones in their previous location. Fitting the new glass on sticky tape has to be done accurately. (no problem). Assembling it was little tricky but still within the ability of a do-it-selfers. We wondered if we should not put the rough side of the glass facing in or out. The original was with the smooth side out so that what we did. If any additional scraping of accumulated grease is needed especially on the inside glass, it requires more disassembly, but we would strongly suggest doing it (we did), while it is all opened. To our surprise the glass arrived by Fed Ex within 24 hours of ordering and now our Whirlpool is gleaming like new again. The cost of this product with shipping/handling by PartsSelect was much lower than ordering it from the other "original" source. Thank you! Sincerely Fred T.

Bottom door trim was rusted

  • Customer: Timothy from Terre Haute IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 3 people found this instruction helpful
Removed oven door and the 3 screws holding the bottom door trim. Attached new trim piece and reinstalled oven door. Entire job took less than 5 minutes.

Glass top stove element stopped working

  • Customer: Robert from Fruitland Park FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 3 people found this instruction helpful
really easy! Removed 2 screws under the glass top at the front, access from the open oven door, then removed the ground wire, removed the stove top, took the element holder off,( 2 screws)and replaced with new element, 30 minutes. I ordered the part and came within 18 hrs of ordering it, fantastic experience.
All Instructions for the RF362LXSS0
46-60 of 127