The French door divider spring fits most Samsung French door style refrigerators. The spring applies tension between components in the refrigerator, which engages and retracts the door flap. This will...
This pin acts as a sleeve for the French door spring in a refrigerator. This is a genuine OEM part that is sold individually and works with the spring within the door mullion to seal the door shut. If...
This is a French door hinge that is compatible with various models of refrigerators and is used to control the mullion (long plastic strips) on the inside portion of the French doors. If you notice th...
The ice maker cube tray holds the water that comes from the ice maker during the process of it becoming ice. This part is white in color and made of plastic. All you will need for this repair is a fla...
This evaporator fan motor is sourced from the original manufacturer for use in refrigerators. It circulates cold air throughout the refrigerator compartment to maintain consistent cooling. If the evap...
This sensor cover, also known as the ice maker thermostat cover, is a genuine OEM replacement part for Samsung refrigerators. It is made of durable white plastic and has measurements of approximately ...
This genuine OEM water filter is made for your side-by-side or French door refrigerator, working to reduce impurities like iron, chlorine, and rust for better-tasting water. With a capacity of 300 gal...
Ask our experts a question about this model and we'll get back to you as soon as possible!
1 question answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Tony
September 7, 2021
Ice maker not making ice
For model number RF266ABWP
Hello Tony, Thank you for contacting us. We have researched the model you have provided and have found the part you are looking for is PartSelect Number PS5575313. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
OMG seriously! I stopped into my go-to appliance repair shop to ask about what might be needed to repair the problem with my refrigerator door. They said you will need to replace the Mullion Flap piece. Cost would be $250-300 with part, labor and service. I went on line to see if I could handle the repair process myself. I found a How to
... Read more - U Tube video and turns out I only needed to replace a little spring and pin not the whole Mullion Flap. Went to Parts select, ordered the spring and pin and did the repair myself in about 5 minutes. Shipping was $7 so I ended up paying $13 total.
The installation video notes that the door mullion spring has a bent end, and that the bent end of the spring is to be inserted into the LOWER hinge. However, on my refrigerator door, the bent end of the door mullion spring must be inserted into the UPPER hinge in order for the door to function properly. (Also noted that in your video t
... Read morehe installer manually closed the door mullion rather than just closing the refrigerator door, another indication that the installation of the spring was incorrect.) After watching the video several times to confirm I was installing the door mullion spring according to the video instructions, I tried inserting the bent end of the door mullion spring into the upper hinge, which proved to be the correct installation of the door mull spring. What should have been a 5 minute repair turned into an ½ hour repair.
There is a pretty good video about this on youtube, but complications arose nonetheless. The replacement spring supplied by Partselect is a bit different from the original in two ways. First, it is made of heavier-gauge wire; this is a good thing for durability, but it makes installation tougher. Second, the ends of the spring, which a
... Read morere bent at right angles to the spring axis in order to fit into the plastic sleeves that hold the spring ends, are far too long. Once I figured this out, i snipped the ends down by a quarter inch or so, and they fit into the sleeves just fine after a certain amount of persuasion from needle-nose pliers. All things considered, it was a bit harder than it should have been, but the door works now, so all is well.