Models > REX6634RQ1 > Instructions

REX6634RQ1 Roper Dryer - Instructions

All installation instructions for REX6634RQ1 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the REX6634RQ1
1,696-1,710 of 1,792
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

belt broke

  • Customer: Terry from Holday FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I have never done this before, so I watched the video and also watched a youtube video for this model to repair belt. Used a gallon paint can to hold up the drum, while I secured the belt. whoooo hooo I did it all by myself...59 yr old Female Do it yourself enthusiast! Thanks for all the information.

the clothes drum stopped turning

  • Customer: Joseph from E.Northport NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
i first watched a video on U-Tube and did exactly as they did. removed screws from the lint tray, pried up the top panel of the dryer with my putty knife, unscrewed the 2 hex screws at the top, disconnected the plug for the dryer door,and installed the new belt it really was pretty easy. the only thing I would recomend would be when installing the belt put towel or anything that would protect your arm from the botttom piece of sheet metal. I got a pretty good cut on my forearm while I was putting the belt on the bottom pully.

Dryer belt broke

  • Customer: John from Lexington NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Pulled up a You-Tube vid on how to install the belt. Went perfect.

broken drum belt

  • Customer: Richard from Westmorland CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Shut off power. Opened the top, removed 2 screws one on each side of front door. Opened clip and removed switch and unplugged wire. Removed front door by lifting it up off bottom clips. Removed the drum and checked the drum support wheels, idler and motor pulley. Shop vacuumed everything to get all the lint, dirt and spider webs out. I was lucky, my idler has a spring, so I cut a small piece of wood and put it between the exhaust pipe and the idler to keep it out of the way. I replaced the drum, slipped the belt over the drum and centered it over the pulley (old belt mark on the drum). I reached under the right side and put the belt around the motor pulley and carefully removed the wood holding the idler, turned the drum by hand to check it. Set the front door back in place, plugged the wire back in, put the switch back in the clip, put the 2 screws back in, turned the drum by hand again. OK! Turned power back on and started the dryer. Total new belt installation time was under 10 minutes.

Broken Blower Wheel

  • Customer: James from Mosca CO
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Remove the back panel, then remove the housing around the blower, just slide the housing of to the side, you don't have to take it completly of the machine. Remove the top, and remove the front until you can get to the blower motor. Cut the blower wheel plastic down to the metal nut with a fine blade in a recipricating saw, used a bi-directional broken stud remover socket on the nut that was at the center of the blower wheel and large slip joint plyer on the other end of the shaft. Replace the wheel and put back together. It took about as much time to gather up the tools as it did to fix it.,

I had to spin drum for dryer to start, bad start winding on motor, not sure if the problem could have been fixed by replacing the motor contactor. I could not find a part # for just the contactor.

  • Customer: Dale from Joanna SC
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
You have to disassemble the dryer. I looked up how to on youtube.com. I am grateful that people take the time to record the steps in which to do just about anything. Disassembled and ordered motor and fan, damaged fan taking it off, got it in in just a couple of days, installed motor, fan and drum, tested before complete assembly. Works great. Thanks

Dryer would not run

  • Customer: Joe from Harrisburg PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Motor was tight, very hard to turn by hand. take the back motor mount strap off and you will be able to put an adjustable wrench on the shaft of the blower. you should be able to put vice grips on the pulley end and turn motor counter clock wise (CCW) to let handle of vice grips rest against the bottom of the machine and turn adjustable wrench CCW to turn off blower wheel. However, the one I did, the wheel was so tight I ended up having to break the blower wheel down small enough so I could pull the motor out. remove the front motor mount strap and pull the motor out. Install the new motor wheel and motor in the revers order. Set motor in place, install front motor mount strap, put blower wheel in from the back of the machine and start treading on the motor shaft. Then,from the front, tighten the blower with wrenches turning clock wise and put machine back together. Always unplug machine whenever working on it. If you go to Whirlpool web site there is a step by step video that will walk you through this entire process.

blower wheel cracked and broke

  • Customer: Kellie from Norton MA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
i took the back apart to find the problem, then i went online to findout how tomremove the blower wheel, just googled it. Easy!Took itnall apart, just had a bit of trouble getting the wheel off, was on there very very tight. Ordered it through you, easy, and very very quick, received it in a day. I got an email explaining the reassembly process. Easy. Just follow it to a t and you will be fine. As a woman, this was an easy fix.

timer not working

  • Customer: ralph from santa rosa bch FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
remove accese panel remove timer place wires one at a time remount timer

Timer would not advance

  • Customer: pamela from ocean springs MS
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I unplugged dryer. Took the top back plate off. Removed the dial and the screw on the front. Removed the two screws from the back and pulled the timer out. Pulled wires off one at a time and put them on the new time in the exact place and screwed it in. Put the screw and front plate on and plugged dryer in and checked it. It worked. Unplugged dryer again and put back plate back on. Done

replace the lint filter

  • Customer: James from Bronx NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
took out the old filter and put in the new lint filter...it was a snug fit.

The lint screen was broken

  • Customer: Melanie from Staples MN
  • Difficulty: Very Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
I ordered a new lint screen to replace the old. I used the part #. They only had "similar" products, not one exactly like mine. When the new part arrived, I had to take IT apart and use part of the new with part of the old, to get a working lint screen. I was able to do it only because of my internal sense of mechanics...and I am proud to say I am a woman!

ice tray was broken

  • Customer: mike from fitchburg MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
This was by far so easy the instruction Partselect gave me where right on step by step. a repair man was going to charge 75$ just to come out 9$ from partselect. Thank you very much Mike chaplin

Washer overflowed

  • Customer: Beth from Valley Springs CA
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Once I watched a YouTube video showing me how to do the job I ordered the part from you. Am so impressed with your fast shipping and best prices via the Internet. Thank you SO much! The water level switch was easy to install, it ws getting the cover on the washer back on that was hard for me since I am 68 yrs old and have a bad knee. Its why it took me two hours to do what most people could do in 20 minutes.

The leveling foot on my dryer broke.

  • Customer: Diana from Clifton NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
We only had to tilt the dryer enough to be able to screw the leveling leg in place.The only hard part was holding the dryer steady to screw in the leveling foot.
All Instructions for the REX6634RQ1
1,696-1,710 of 1,792