REX6634RQ0 Roper Dryer - Instructions

I purchased the maintenance kit and followed the video on part select.com. Replacing the drum wheels, pully and belt was not difficult. I probably found enough coins in the dryer to pay for the maintenance kit. The only tricky part was getting the cap on the end of the axle. It requires a bit of force applied evenly.

Door latch or kill switch. Rewarding experience to fix on own.

Unplug the dryer, remove hot air duct. Remove metal dryer back to access thermostat using a nut driver. Unscrew one screw holding on thermostat, detach 4 wires, and replace with new unit, attaching 4 wires to new unit. Then reverse process to button up the dryer. Great how-to video on your site helped a lot!

I took off all the back plates of dryer. (2 sets). Then I took off the heating element. It appeared to be in tact but had some blackening coloration on plate. Ordered new part, replaced the element (tested before I put the back plates back on) and it worked perfectly again. I was especially happy with Parts Select because I ordered the part on a Sunday night and it arrived on Tuesday at noon (regular shipping)!!

Unplugged dryer. Removed control panel end caps, removed anchor screw at each end of control panel that had been covered by end cap. Tilted control panel up to access components on back side. Using tech sheet found inside contol panel, swapped motor relay with heater relay (they're identical). Plugged dryer back in, pushed start switch; dryer continued to run (problem identified). Unplugged dryer; replaced relays to original positions. Ordered new power relay (p/n 3405281). Installed new relay when it arrived, plugged dryer in, tested it. Dryer worked normally (problem fixed). Unplugged dryer, reinstalled control panel anchor screws and end caps. Plugged dryer back in. Dryer continues to work normally.

after process of elimination ,figured had to be cut off switch followed simple instructions also watched your video..simple repair up and working again approx. 30 min. once i had kit. thanx 4 the help MIKE

I watched the video several times to make sure I got it right. The first thing that was very helpful was how to disassemble the top cover and front panel using a putty knife to disengage the detents. With the cover off I could acccess the belt and idler pulley. Replacing the belt was fairly easy as long as you note the way it threads through the idler pulley and drive pulley. I thought the video was excellent. It took me right to the problem and the fix. As a bonus the price for the belt was much lower from Parts Supply then from Sears. I've recommended this site to several others.

Just as your helpfull diagram of the dryer said, removed the rear panel,there it was, i recongnised it by the part you sent, pull it out of it's position, had a little truble figuring out the piece that fits on where the electric prongs are, after looking found out the piece was held on with a clip that goes inside the housing, Haaa. the rest was easy. Thanks,It works great. Dick

First I purchased the heating element, still no heat. Then I purchased the thermal fuse,still no heat. I have been pleased with the prompt shipment of the parts and the parts arrived safe. Thank you for service and time, not sure what to do now.I will recommend PartSelect to friends.

Unplug unit / removed back cover / went down , locating both parts to be replaced / simple one screw removal from each part / thermal fuse , one wire @ a time , reinstalled . / Cycling thermostat , 4 wires. Did one wire @ a time , reinstalled. / Putted back cover back on , plugged dryier back up, turned it on to run. To check for heat / yes, ran good as new. Later that day some more running , with damp clothes in it. Did it's job , dry.

I followed the repair method as described in the how to video it was as easy as that. Dryer is now working perfectly

Took the back off of the dryer, looked on "parts select" found what I thought might be the problem. Got the parts the next day. Put on new thermal fuse, then put on cycling thermostat. Wasn't sure which it needed, so put both on. Put the back of the dryer on hooked the gas up, hooked up to electric, & turned the dryer on. Back in business, everything works, dryer works as if nothing was wrong. Thanks to "parts select" saved me a repair bill.

I watched your video on how to replace the fuse.Wow it was a lot easier than I thought.I would highly reccomend anyone to watch the video before even trying to do any repairs.The dryer is working like a new one.By doing it myself saved me a lot of money.Thank you

Removed two screws at the top, removed two screws for the front panel, removed the broken belt, installed the new belt, followed the directions that were in the new belt package, and replaced all the panels and tested. It worked.

Just as in the video. Sounds like new. Had to feel it to make sure it was running.