Models > REX6634PQ0 > Instructions

REX6634PQ0 Roper Dryer - Instructions

All installation instructions for REX6634PQ0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the REX6634PQ0
1,696-1,710 of 1,819
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

the dryer belt broke (worn out)

  • Customer: ROBERT from BELMONT, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Opened up the dryer, to discover the broken belt at the bottom, read model, serial number. Went on line, found sites that gave parts lists and diagrams. Wrote down part no. Used Safari to find the part. PartsSelect was cheapest, had it in stock, and could ship fastest. Sears was more expensive and slower. The part arrived in 3 days as promised.Overall, it was excellent service.

belt broke

  • Customer: Terry from Holday, FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I have never done this before, so I watched the video and also watched a youtube video for this model to repair belt. Used a gallon paint can to hold up the drum, while I secured the belt. whoooo hooo I did it all by myself...59 yr old Female Do it yourself enthusiast! Thanks for all the information.

the clothes drum stopped turning

  • Customer: Joseph from E.Northport, NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
i first watched a video on U-Tube and did exactly as they did. removed screws from the lint tray, pried up the top panel of the dryer with my putty knife, unscrewed the 2 hex screws at the top, disconnected the plug for the dryer door,and installed the new belt it really was pretty easy. the only thing I would recomend would be when installing the belt put towel or anything that would protect your arm from the botttom piece of sheet metal. I got a pretty good cut on my forearm while I was putting the belt on the bottom pully.

Dryer belt broke

  • Customer: John from Lexington, NC
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Pulled up a You-Tube vid on how to install the belt. Went perfect.

The drum would not tumble.

  • Customer: Renae from Hegins, PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
We watched the video on the PARTS SELECT site and it was very helpful and I had no problem holding the flashlight for my husband!

Belt broke on dryer, drum therefore wouldn't tumble

  • Customer: Elaine from North Berwick, ME
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Had a hard time at first trying to figure out how to place the pulley wheel that you place the belt around, it holds it in place so to speak, was getting very frustrated came upstairs went on line to your web site and lo & behold there was a video on how to do it, I watched that video (thanks Steve) and went back down cellar and had the belt on in less than 5 mins and everything is working fine. Thanks for all your help Dan

drum not turning

  • Customer: Edward from Shrewsbury, MA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
push in on clips on front top at seams apx 2-3 inches from both sides. lift lid lean it back. remove door switch. remove front panel. remove old belt. replace with new belt lifting drum slightly to get around drum rib side down. reach in and push tensioner down to the left place belt around pully and over tensioner relase gently put all item back together.

Belt on dryer drum broke

  • Customer: Thomas from Buffalo, NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
The repair on replacing the clothes dryer belt went great. Not only did Part Select send me the correct belt at a great price .. the helpful hints that other people gave was most helpful. The only glitch was when I was pushing the tensioner wheel to get the belt around the pulley it slipped and the spring came off. The instructions/tip of taking the drum out and how to replace it came in handy when I had to get the spring back into place. The belt finally went on but there was a slight twist in it by the tensioner wheel. Again the tip I got with my e-mail helped as I manually turned the drum and was able to right the belt. Kudos to the tips I received and the confidence I could do the job myself!!!!

broken drum belt

  • Customer: Richard from Westmorland, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Shut off power. Opened the top, removed 2 screws one on each side of front door. Opened clip and removed switch and unplugged wire. Removed front door by lifting it up off bottom clips. Removed the drum and checked the drum support wheels, idler and motor pulley. Shop vacuumed everything to get all the lint, dirt and spider webs out. I was lucky, my idler has a spring, so I cut a small piece of wood and put it between the exhaust pipe and the idler to keep it out of the way. I replaced the drum, slipped the belt over the drum and centered it over the pulley (old belt mark on the drum). I reached under the right side and put the belt around the motor pulley and carefully removed the wood holding the idler, turned the drum by hand to check it. Set the front door back in place, plugged the wire back in, put the switch back in the clip, put the 2 screws back in, turned the drum by hand again. OK! Turned power back on and started the dryer. Total new belt installation time was under 10 minutes.

I had to spin drum for dryer to start, bad start winding on motor, not sure if the problem could have been fixed by replacing the motor contactor. I could not find a part # for just the contactor.

  • Customer: Dale from Joanna, SC
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
You have to disassemble the dryer. I looked up how to on youtube.com. I am grateful that people take the time to record the steps in which to do just about anything. Disassembled and ordered motor and fan, damaged fan taking it off, got it in in just a couple of days, installed motor, fan and drum, tested before complete assembly. Works great. Thanks

blower wheel cracked and broke

  • Customer: Kellie from Norton, MA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
i took the back apart to find the problem, then i went online to findout how tomremove the blower wheel, just googled it. Easy!Took itnall apart, just had a bit of trouble getting the wheel off, was on there very very tight. Ordered it through you, easy, and very very quick, received it in a day. I got an email explaining the reassembly process. Easy. Just follow it to a t and you will be fine. As a woman, this was an easy fix.

Dryer would not run

  • Customer: Joe from Harrisburg, PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
Motor was tight, very hard to turn by hand. take the back motor mount strap off and you will be able to put an adjustable wrench on the shaft of the blower. you should be able to put vice grips on the pulley end and turn motor counter clock wise (CCW) to let handle of vice grips rest against the bottom of the machine and turn adjustable wrench CCW to turn off blower wheel. However, the one I did, the wheel was so tight I ended up having to break the blower wheel down small enough so I could pull the motor out. remove the front motor mount strap and pull the motor out. Install the new motor wheel and motor in the revers order. Set motor in place, install front motor mount strap, put blower wheel in from the back of the machine and start treading on the motor shaft. Then,from the front, tighten the blower with wrenches turning clock wise and put machine back together. Always unplug machine whenever working on it. If you go to Whirlpool web site there is a step by step video that will walk you through this entire process.

timer not working

  • Customer: ralph from santa rosa bch, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
remove accese panel remove timer place wires one at a time remount timer

Timer would not advance

  • Customer: pamela from ocean springs, MS
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I unplugged dryer. Took the top back plate off. Removed the dial and the screw on the front. Removed the two screws from the back and pulled the timer out. Pulled wires off one at a time and put them on the new time in the exact place and screwed it in. Put the screw and front plate on and plugged dryer in and checked it. It worked. Unplugged dryer again and put back plate back on. Done

on-off switch

  • Customer: vincent from lesterville, MO
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
took off the back part with nut driver removed switch assembly by pressing down with a little pressure and it snapped out the new was a little different but worked on installing this was an easy assembly. just do things in reverse when finished just plug in electric and push switch to turn on. very easy to install.
All Instructions for the REX6634PQ0
1,696-1,710 of 1,819