Models > REX6634PQ0 > Instructions

REX6634PQ0 Roper Dryer - Instructions

All installation instructions for REX6634PQ0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the REX6634PQ0
1,666-1,680 of 1,792
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Squeaky Idler Pulley

  • Customer: Mitchell A. from Hampton NH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the video that showed how to do the repair. I did exactly what I was shown on the video, and everything worked the very first time ! It was GREAT ! No more squeaking idle pulley !

Belt & clip where both broken

  • Customer: Amy from Seagrove NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
My 11 year old son and I ordered the parts we needed. Saw the GREAT easy installation video, It even was attached to my confirmation. After the parts got here him and I easily took off the old belt and clip, installed the new ones (after watching the viedo again) and we where done. You would have thought we fixed the space shuttle or something because we both smiled all day. My son also told every one that he and his mom fixed the dryer all by ourselves. Costed me only $40 dollars for the parts. I couldn't have even called a repair man out there for that. Thanks soo much.

Lould nosie from Drum Whells

  • Customer: FRANCIS from PHILADELPHIA PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I watch and followed the three viedos that PartSelect emailed me and had a very easy repair job.

Broken belt and bent idler pulley

  • Customer: Mollie from Walterboro SC
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
First unplug the unit. Take the lint filter out and remove the two Phillips-head screws at the edge of the opening. Then using the putty knife to unlatch the top panel of the dryer, insert it into the seam on the front about 3" from each side. When you feel the knife up-against the latch, apply a little inward pressure with the knife and pull up on the top panel. When you release both sides the panel, it will lift up and back against the wall(secure it so it doesn't fall forward while you are doing this repair). Looking down on the right-front corner you will find a connection for the door switch, Dis-connect it. Just below that connection, on the inside, is a 5/16" screw that holds the front panel on, take that one and another one just like it on the left side, out and the front will fall forward about an inch and then you will lift up on the panel while holding drum in place. Inspect the clips that hold the bottom of the panel on and be aware how the panel attaches to them. Try to keep the drum in place and set the front panel off to the side so you can easily grab it to put it back on. Looking under the drum remove the belt and idler pulley. The pulley is usually not in the position it should be in, it likes to fall over when it has no belt pressure on it. Hopefully you had already unpackaged the new belt and straightened it out. Loop the belt over the drum, rib side to the drum, and move it to where the old belt had been riding on the drum. Back under the drum, you should hold it in place with your shoulder, with idler pulley in hand-- install the idler pulley. There's probable a clean spot where the old one was and the humpback should point to the right side of the dryer. With right hand steadying the idler pulley, the left hand should pinch the belt together and feed it under the wheel and pull it out and hook it on the motor pulley. It may seem to be a tight fit but once its on you should be able grab the outside edge of the drum and slowly turn it without hearing any scraping noises. Double check that the belt isn't twisted. Before putting the front panel back on or if you had to take the drum out, make sure the felt seal on the back edge of the drum is not folded inward. the wheels that the drum roll on must be in the groove. Carefully reach to the back to check that they are in the groove of the drum. If everything seems to be in place, hold the drum with one hand and grab the front panel with other. Place the bottom of the panel against the unit and lift up about an inch and place the square holes at the bottom of the panel on the clips on the unit, it may take a couple of tries, then lean the panel forward making sure the drum goes around the felt seal on the panel. Once the panel is against the unit , install the two 5/16 screws securing the front panel to the unit. Turn the drum by hand to make sure drum was installed properly. Reconnect door switch. Lower top panel and push down to secure it. Install the two Phillips head screws at the edge of where the lint screen goes, install lent screen and plug the unit back into the wall socket.

drum not turning

  • Customer: Tony from Greenville IL
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Watched a video on utube and realized how easy this looked, took my dryer apart to see the belt broken in half and the idler pulley in pieces. Found Partselect on the internet and ordered my parts. Partselect was awsome, website was easy to navigate, ordered my parts and they were at my house the very next day and were the correct parts. Cleaned all the lint and dust out of the inside of my machine, installed new parts and put it back together. Works great and is still running strong. A service call, plus parts (with thier mark up) could have easily been $150.00 - $200.00 dollars. this repair was complete in about an hour and only cost me $37.50

Loud humming noise then motor would stop

  • Customer: Clarke from Lynnwood WA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
The dryer would make a loud humming noise and the seize up. I would reset the breaker and the dryer would run briefly and then seize up. I opened the dryer and cleaned out all the lint on the motor but it did not help. I spun the motor shaft and felt like a bearing inside had failed. I watched Steve in the video-he was awesome and made it all simple- and ordered the correct parts. I decided to replace the rollers, belt, and pulley as well as the motor. The repair is very easy-and worth it- EXCEPT one piece of advice. BUY the blower fan that attaches to the motor. Mine did not come off easily like in the video. The plastic shaft deteriorated under pressure from the wrench. I was forced to use a heat gun to melt/then cut the blower fan from the motor. It was not easy but don't let it deter you from the repair. I used a table vice but never could remove the remanents of the blower fan shaft from the motor. The repair was a snap after that. Great site for parts and help.

dryer was loud when in operation

  • Customer: daniel from saint charles MO
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
actually your site was very helpful in describing each part that i chose to replace. one helpful hint to someone when installing the dryer pulley is to use the parts box to hold up the drum when installing.it seemed to be the perfect size. great site!

Dryer wouldn't start... Just a hum when you press the start button.

  • Customer: James from Festus MO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Well it took me longer to get the dryer apart and than it did to get it back together... Well I opened it up it was obvious I had burned up the motor you couldn't even see it for all the lint that was built up around it... And the hardest part was removing the fan from the motor shaft, I didn't realize it was plastic and sort of mangled it getting it off so I went ahead and replaced it as well. The hardest part of the whole repair was removing and replacing the clips that hold the motor in place and there didn't seem to be any trick to it, I used a pair of channel locks and a little muscle to get them off and back on everything else was a breeze! I recommend checking the exhaust pipe at least once a year to make sure air is flowing freely to prevent the lint build up inside and even more often if you have a long run. This should prevent having this problem again...

i had difficult time getting wheel off.

  • Customer: dwight from monticello AR
  • Difficulty: Very Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
found out that pushing in on wheel and turning counter clock wise, wheel screws off rather easy.

broken wheel

  • Customer: Ray from Coleman TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
I had purchased a motor for the dryer first. The blower wheel broke while I was trying to take the motor off from the blower wheel. Installing the new wheel was fairly easy once I took the blower cover of at the back of the dryer and literally brake the wheel of the motor shaft.

replace the lint filter

  • Customer: James from Bronx NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
took out the old filter and put in the new lint filter...it was a snug fit.

The lint screen was broken

  • Customer: Melanie from Staples MN
  • Difficulty: Very Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
I ordered a new lint screen to replace the old. I used the part #. They only had "similar" products, not one exactly like mine. When the new part arrived, I had to take IT apart and use part of the new with part of the old, to get a working lint screen. I was able to do it only because of my internal sense of mechanics...and I am proud to say I am a woman!

ice tray was broken

  • Customer: mike from fitchburg MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
This was by far so easy the instruction Partselect gave me where right on step by step. a repair man was going to charge 75$ just to come out 9$ from partselect. Thank you very much Mike chaplin

Washer overflowed

  • Customer: Beth from Valley Springs CA
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Once I watched a YouTube video showing me how to do the job I ordered the part from you. Am so impressed with your fast shipping and best prices via the Internet. Thank you SO much! The water level switch was easy to install, it ws getting the cover on the washer back on that was hard for me since I am 68 yrs old and have a bad knee. Its why it took me two hours to do what most people could do in 20 minutes.

The leveling foot on my dryer broke.

  • Customer: Diana from Clifton NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
We only had to tilt the dryer enough to be able to screw the leveling leg in place.The only hard part was holding the dryer steady to screw in the leveling foot.
All Instructions for the REX6634PQ0
1,666-1,680 of 1,792