Models > REX5634PQ0 > Instructions

REX5634PQ0 Roper Dryer - Instructions

All installation instructions for REX5634PQ0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the REX5634PQ0
1,621-1,635 of 1,792
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broken Belt

  • Customer: Jeffrey from Bensalem PA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Watch the video you sent me, and every thing fell into place

Broken Multi Rib Belt - 92 - 1/4"

  • Customer: Michael from San Juan Capistrano CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Exactly as described by the video.

Starter would not stay on after pushing on

  • Customer: Rosemary from Ellicott City MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Followed video, very easy installation. Unfortunately, the new starter switch does not stay on either so we still have not resolved the problem.

the drter would not start

  • Customer: linda from South Lebanon OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
since dryers are hard for me to determine. I used my OHMs meter to see that the Thermal Fuse was good. The door switch was good . The off on switch was bad.

push to start switch didnt work

  • Customer: LEE from BUTLER TN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
removed access panel installed new switch reinstalled access panel

clothes dryer wouldn't continue to run after push-to-start switch was released

  • Customer: Mo from Portland OR
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Unplugged dryer. Removed control panel end caps, removed anchor screw at each end of control panel that had been covered by end cap. Tilted control panel up to access components on back side. Using tech sheet found inside contol panel, swapped motor relay with heater relay (they're identical). Plugged dryer back in, pushed start switch; dryer continued to run (problem identified). Unplugged dryer; replaced relays to original positions. Ordered new power relay (p/n 3405281). Installed new relay when it arrived, plugged dryer in, tested it. Dryer worked normally (problem fixed). Unplugged dryer, reinstalled control panel anchor screws and end caps. Plugged dryer back in. Dryer continues to work normally.

Dryer would not start

  • Customer: Kevin from Fly Creek NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Your website described the probability of the problem as being one or both of the replacement parts I bought. You were right. I replaced the two parts and the dryer started and has been operating flawlessly ever since. I would also like to commend you on your very rapid shipping of the parts. I recieved them in less than 24 hours, via Fed-Ex Ground.

m

  • Customer: Jo Lynn from Cape Canaveral FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Installed both parts but still doesn't heat. Probably have to buy a dryer because a new element will be about $80. Your response and delivery time were great as were the instructions.

Clothes were coming out damp after the drying cycle.

  • Customer: Michael from Fountain Inn SC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
i replaced both the high limit and cycling thermostats because cost was not that much and these thermostats change settings as they age. After replacing the thermostats the problem was solved.

No heat

  • Customer: Charles from Monument Beach MA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Click on the problem and find the possible solutions. Click on the part and watch the installation instructions. Unfortunately, mine was a bad thermostat/fuse that can only be purchased with the High Limit Thermostat which I had already purchased. What you might find helpful is that all thermostats and fuses should show continuity at room temperature when using an Ohm meter. Both purchases arrived within 30 hrs. of shipping. I was impressed. I ended up changing all three thermostats but was still way ahead considering a service call is $140 plus parts. I almost scheduled this service until stumbling onto this site thinking the heater was bad but was much cheaper than the local appliance/repair store. Again, the continuity test showed that the heater was fine and everything already mentioned above could be inspected and changed in less than 10 minutes.

Not enough heat

  • Customer: Steve from Yadkinville NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Unplugged Dryer. Removed back panel of the dryer. Disconnected and removed the Thermal Cut Off switch and replaced. Disconnected and removed the High Limit Thermostat and replaced. Reinstalled rear panel of the dryer. Plugged in dryer. Operated dryer and checked for heat. Operation was proper and dryer works great.

Dryer would not heat up.

  • Customer: John from Quincy CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the repair expert on you tube. Went to my dryer and took out the heating element, inspected it, and found a broken element wire. Ordered a new element and since I was in there I also replaced the high limit thermostat. Parts select made it easy and my dryer works great again. Thank you.

No Heat. Timer Wasn't Moving.

  • Customer: tartty from Wilkes Barre PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
First I watched the videos to be sure these parts were easily accessible. After determining the heating element was the problem, I decided to change the other parts only because they were so simple to change. I paid just shy of $100 for parts and fixed the dryer myself, saving who knows how much from a service call. This was by far the easiest appliance repair I've ever done. Thank you PartSelect.

no heat during cycle

  • Customer: Patrick from Ulysses KS
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
My grandson and I wiggled the dryer out of it's tight hole, turned it around and squeezed it back in to make room for the repair job. I followed the easy repair video on your site and removed the housing etc, vacuumed the lint collected over the past 6 years, replaced the heater coil and sensor, and had it back within an hour, with most of the time spent on cleaning lint. Thanks for the video!! This kind of DIY can be fun with the right info. Great bonding-time for generation gap, too. Dryer works like new.

Dryer stopped heating

  • Customer: Larry from Junction City KS
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I thought I would do it myself and figured that because it wasn't heating I would replace all the thermostats and thermal fuse. Because I wanted to get it going right away, I also ordered a timer just incase. Turns out it was the timer and not the thermostats or fuze. I have a virtually new dryer again. Replacing the parts was really easy and didn't take long. Word of advise is to use an electrical (ohm) tester to determine which part is faulty; this will also save money by not buying not-needed parts.
All Instructions for the REX5634PQ0
1,621-1,635 of 1,792