Models > REX5634KQ1 > Instructions

REX5634KQ1 Roper Dryer - Instructions

All installation instructions for REX5634KQ1 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the REX5634KQ1
1,351-1,365 of 1,813
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

My dryer would not turn on at all

  • Customer: Jason from Richmond TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I watched your YouTube video about trouble shooting dryers, and found that the problem was my thermal fuse was out. My exact model of dryer was used in the video. I ordered the part and replaced it following the instructions on YouTube. Since the video was so helpful, I decided to order my part from your company

Dryer was running but not producing heat

  • Customer: Anthony from Elk Grove Village IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Wrench set
  • 0 of 0 people found this instruction helpful
Most of the time was spent just getting behind the dryer and removing the back panel. It was also a great time to vacuum the area. If you're not working in tight quarters, this repair is really easy. The fuse is not hidden and requires no tools to install (only a wrench to remove the back panel). It started working right away & the part cost significantly less than a service call (about nine bucks + shipping).

unit wouldn't light

  • Customer: mark from burbank CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
bought thermal fuse and thermostat as most likely. Took apart and checked with voltmeter and found the fuse open. Replaced it. Video instructions are helpful as is the part location in the drawings. Real problem was lint had built up in back vent area, blocking cooling/ burner intake air. Went through entire dryer and vacuumed it out

Belt Broke

  • Customer: Dann from Granville NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the video to know how to change the belt. I removed the front panel and slid the belt over the tub (you will have to pick the tub up a little). Then I reached around with one hand and slid the belt over the pulley. Then I used the same one hand to push the tensioner back and slip the belt behind it. You will be doing most of the work by feeling not by vision but that's where their video is helpful. I paused the screen on my laptop where it shows how the tensioner goes around the belt. Also when you slide the belt over the tub look for the grove the previous belt left for alignment. It took me 10 minutes.

Drum does not rotate, motor runs and it heats

  • Customer: Barry from Virginia Beach VA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
1. Opened the top. (UN-plugged it first) by prying between top and front of machine.
2. Disconnected the door switch
3. Removed two screws one each on top corners of front
4. Pulled top of front cover forward and lifted up to remove.
5. The drum will fallout if not careful, good time to remove drum to clean dust from inside machine.
6. With drum in place slide new belt, skinny side down around drum, to about halve way back.
7. While supporting drum reach back to the motor area, should be on right side facing front of machine. There you will find the belt idler/tension assembly.
8. Thread the belt through the assembly and around the motor drive pulley.
9. Ensure the tensioning assembly is firmly in the slots on floor of machine.
10. Reassemble housing in reverse order. took about 45 minutes

the dryer was heating but the drum wasn't turning

  • Customer: DOROTHY from DINGMANFERRY PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I watched the video on the computer and it was very easy to repair I had the dyer apart ,fixed and put together in about half hour

Drum not turning / belt broken

  • Customer: Jill from Bangor PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I won't tell you how we did it, but I'll tell you the right way. Unplug. Remove the exhaust tubing attached to back of dryer. Pry the top up from the front and lean it against the wall. Un plug the wires attached to the front panel (remember where they go) Remove screws at top sides of front panel. "lift up" and remove. Close top. Lay machine on its back. We used a couple of 2x4's to lay it on so as not to crush the vest collar. Clean it out, including lint filter. The new belt wraps around the drum, you will see the channel about midway on drum. Feel behind the motor on the lower right side. There is a shaft with a channel for the belt. Immediately next to that is another pulley type arm with another channel for the belt. This arm moves stiffly and puts tension on the belt when installed correctly. Look at the diagram included with the new belt which shows the path of the belt. Wrap the belt, ridges against the drum and then around the motor shaft. At this point you have to physically pull the last arm out to allow the belt to wrap around the channel provided. If the belt is not twisted , the job is done. Turn the drum with your hands to make sure it is turning properly. Replace the front panel, plug in the electricals, replace the screws making sure the drum is properly centered. Stand up the dryer. Plug in and turn on dryer to make sure everything is right. Replace the exhaust tubing and set into place. Sounds like a lot of steps but I have described the whole process for you beginners. The rest of you will know already. Good Luck . Oh by the way we are 69 and 71. If we can do it, so can you

Broken belt

  • Customer: Clayton from Girard KS
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed video instructions. Raised the top, slipped off the front, installed the belt, aligned, installed tension part, reinstalled front, lowered the top and inserted lint trap. Job done. Quick and easy. The video was the key to the whole project.

Installed a new belt

  • Customer: Timothy W from Lakeland FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
The video you had of my dryer was different then my dryer and the pulley was in the middle of the bottom and the motor and fan were in front of it. I had to replace the belt without being able to see what I was doing. I couldn't get it at first then realized there was tension on the pulley wheel and had to pull it towards the other wheel in order to get the belt on there. Once I pulled the wheel it went on really easy. My first time working on a dryer but I knew I could do it myself.

broken dryer belt

  • Customer: Thomas from Waterford NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
instructions were clear and repair was easy

Does not turn or tumble

  • Customer: Charles Weston from Pikesville MD
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Well, to Figure the issue I took the entire thing apart. Actually a lot more than needed. I found the torn belt and ordered it. I did not realize I may need a new belt tensioner which is sold with a wheel for the belt to wrap around and be tensioned by. Actually the original just utilized a rubber c or u shaped design(no wheel) for the belt to slide over. Anyways, instead of ordering and waiting for a new wheeled belt tensioner, I installed new belt with all original parts and working fine. I did oil up the drum rollers to reduce noise. And since I took the whole thing apart I cleaned the lint from every place it could hide. Ps a coke can is said to be helpful to hold the drum up while installing the belt but I found a jug of laundry detergent did better. Totally easy project for someone with no appliance repair history

broken belt that makes the dryer drum go around

  • Customer: kevin from madison WI
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
The broken belt was found when I opened the dryer. The part number was on the belt and a quick online search led me to PartSelect. The part was available, delivered in less than 2 days and there was an online video showing the entire repair in detail.

Broken Drive Belt

  • Customer: Cosmo from Somerville MA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed two screws at the top, removed two screws for the front panel, removed the broken belt, installed the new belt, followed the directions that were in the new belt package, and replaced all the panels and tested. It worked.

Dryer drum was not turning. Belt was torn.

  • Customer: Donald from Peekskill NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the video several times to make sure I got it right. The first thing that was very helpful was how to disassemble the top cover and front panel using a putty knife to disengage the detents. With the cover off I could acccess the belt and idler pulley. Replacing the belt was fairly easy as long as you note the way it threads through the idler pulley and drive pulley. I thought the video was excellent. It took me right to the problem and the fix. As a bonus the price for the belt was much lower from Parts Supply then from Sears. I've recommended this site to several others.

belt replacement

  • Customer: David from Paris TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
first I took a flat head screw driver to pop the top of the dryer open, and then removed the screws from the lint tray. Next I lifted the lip back making sure it was supported by the wall behind. Third I removed the front of the unit by removing the bolts attached on both ends of the top of the unit. I then opened the door and removed the screws on the right top side of the lining of the door to the switch. Then I carefully held onto the tub while lifting the front face of the unit to remove the face of the dryer. After carefully removing the face I released the tub and set it aside. Then I picked up the tension pulley set it back in its slot followed by placing the belt rib side down around the tub. Next step was to place the tub back in the unit making sure the felt was in place and then I ran the belt back through the tension pulley applying tension in order to get the belt back onto the motor making sure the ribs of the belt aligned up with the ribs on the motors belt drive wheel. After completing that I then grabbed the front panel of the dryer unit and gently replaced the panel making sure that the slots and hooks lined up while placing the tub back in alignment of front panel. Once that was complete I replaced the screws in the door switch followed by replacing the bolts in the inside of the top comer of the front panel till hand tight. Last but not least I slid the lint tray back in place in order to make sure screws did not fall in to the hole the lint tray occupies. After replacing the screws I then plugged in the dryer gave the tub a few spins with my hand to make sure it was in place correctly I gave it a test drive by leaving the door open and pressing the door switch shutting off the light in the unit so it since the door was shut and turn the unit on for a cycle for at least one minute to see if the tub rolled freely on its own. All was good and only took 12 minutes to change and replace part. Easley can be done by any DIY first timers. Me I work with all kinds of units but the older units are easy and no need for a tech I promise.
All Instructions for the REX5634KQ1
1,351-1,365 of 1,813