Models > REX5634KQ1 > Instructions

REX5634KQ1 Roper Dryer - Instructions

All installation instructions for REX5634KQ1 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the REX5634KQ1
1,711-1,724 of 1,724
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broken Dryer Belt

  • Customer: WILLIAM from DELRAY BEACH FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Ordered entire Maintenance kit - good call because it was the tensioner pulley that failed and cut the belt. To replace, had to raise the top (2 screws in lint screen slot)and pull the entire front off (2 screws - 1/ea on top inner edge of front door panel then lift it up and out) Replaced both rollers, then used the parts kit shipping box to prop up the front of the drum while installing the belt and tensioner pully. Re-assembled in reverse order, works fine.

dryer did not spin

  • Customer: Paul from Robbinsville NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
I purchased the maintenance kit and followed the video on part select.com. Replacing the drum wheels, pully and belt was not difficult. I probably found enough coins in the dryer to pay for the maintenance kit. The only tricky part was getting the cap on the end of the axle. It requires a bit of force applied evenly.

Loud squeaky that turned into a rattling noise

  • Customer: Andrew from Chimacum WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I watched your video that showed me how to remove the top then the face of the dryer. I then removed the drum and belt,after which I could then remove the support wheels and the belt tension wheel.I replaced the support wheels and tension wheel,the hardest part was removing the little plastic locking keepers that hold the support wheels in place. After that I was able to reinstall the drum with the new belt and reinstall the face and top of the dryer. My 15 year old dryer works great just like new. Thanks

Belt on dryer replaced

  • Customer: William from Lakeland FL
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The instructions were easy to follow and the pulley on the replacement part was evenbetter quality than the original. I also followed the recommendation to clean the lint trap. Now the dryer works quieter and better than it ever did. Thanks for your product!

Loud "squacking, squeeling noise" during operation

  • Customer: Jon from Hernandez NM
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Found right parts for problem on this website. Handyman took down machine and installed the drum support wheels. Taking apart was not too difficult; getting drum and dryer face aligned properly was a bit difficult and took longer than expected (and 3 of us). However, it was much better than having to buy a new dryer, since there was very little really wrong with this one. BTW, it was "out of warranty" so it would have cost around $150-$250 to repair using the repair service from the retailer we bought it from. Saved lots of money. Thanks.

belt broke

  • Customer: valerie from mishawaka IN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the video online in the order section. then just did it after we received the repair kit.

broken dryer belt

  • Customer: kimberly from petaluma CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Everyone said changing a dryer belt was a piece of cake.They did not tell the truth it is a difficult job. I am a 52 year old female and I had a problem. You have to take the whole drum out. I finally completed the job but i had to prop the drum up with blocks so I could screw in the front panel. I think for those who want to change the belt I would go smoother with two people so the can hold things in place while the other one screws the panels back. I also think taking the dryer door off make the front panel a lot more easier to put in palce.

noisy

  • Customer: Mark from Wood-Ridge NJ
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Following the step by step instructions it took longer to clean the old lint out of the bottom of the dryer than to perform the entire repair.The maintenance kit came complete with every moving part(except the motor and drum)and now it runs very quietly.I am all thumbs when it comes to tools but this was very simple.

Dryer became EXTREMELY noisy

  • Customer: Lawrence from Cape Coral FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Kit arrived with all the parts required and with detailed instructions. LOL... the very specialized tool you will need to dis-assemble the dryer? A PUTTY KNIFE. All in all, aside from the top of the dryer slamming shut without warning and scaring the pants off me, this was a relatively easy repair from a technical level. Only real difficult thing was removing and then restoring the drum and that was more due to clearance than actually being difficult. Make sure once you're finished to LEVEL THE DRYER. That makes a HUGE difference!!!!!

Broken drive belt

  • Customer: Antrhony from Warwick RI
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Removed back cover,top,lower and upper front,and drum. Cleaned dust and dirt drom all of the removed parts and then removed the "lint tube". Took the tube apart to clean out dirt and lint, cleaned the lint off of the motor and blower wheel, and then removed the support wheels. Installed the "lint tube" and then the new support wheels with the new locks and then installed the new belt onto the drum. I had to support the drum in order to correctly line up the belt, and then installed the upper front panel. plugged in the power cord and started the motor to be sure everything was OK before closing up the rest of the cabinet. All was OK and the belt tracted perfectly. Installed the lower front panel, top, and the rear panel. Installed the gas connection, checked for gas leaks and installed the dryer back in place. checked operation with a batch of wet clothes and the dryer worked "better than new"!!! The instruction sheet was "spot on" for clarity and accuracy.

Loud grinding noise while drying

  • Customer: Michael from Blue Springs AL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I ordered the maintenance kit because it was recomended for my application and the symptoms my dryer was exhibiting. However this kit did not apply to my model. My model contained 4 drum rollers, only 2 came with the kit, and the idler pulley setup was completely different. I should have pulled the dryer apart first to compare pictures to the actual parts. No big deal, prompt refund after a quick phone call to Parts select. I was able to fix my idler pulley with a couple of new nylon washers and a new snap ring to hold it in place. Whirlpool cabrio wed6200sw1.

Dryer was clunking very loudly

  • Customer: Jim from Huntington Beach CA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Followed instructions that came with the dryer with the exception of the idler pulley which I didn't install because this maintenance kits idler pulley does not match my dryers. Not even close. I would have had to cut or drill holes to make it work. Since I knew it was the rollers that were the problem. Dryer worked great once I was done, but it probably would have been cheaper for me to order the parts individually without the Idler Pulley if I wasn't going to replace one.

Loud noise when dryer was in use

  • Customer: Anthony from reseda CA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
I unplugged the dryer and removed the front panel. i then looked underneath and removed the belt. at this point this point I was able to remove the drum. once the drum was removed I was able to replace the pulley and wheels. the maintenance kit was just the ticket. I follow the enclosed instructions and I was done in no time. I would suggest taking it apart first so you can make sure you order everything you need the first time.

The dryer sounded like a herd of buffalos running by.

  • Customer: Patrick from Bettendorf IA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I needed to replace our drum support rollers - one was completely worn out and wobbling (the buffalo herd noise) the other wasn't too bad, but for an older dryer(15+ years) I figured it was time to replace both wheels. I ordered the maintenance kit that also included the Idler Pulley and drum belt. I spent most of my time with the vacuum since there was a lot of dust accumulated inside the dryer. (I recoverd $1.83 in coins!) The instructions that came with the kit were very helpful for this repair. Plus, there were some online videos that heled as well. Once I had everything apart I noticed the plastic bearing ring on the drum's front was nearly worn out so I quickly ordered this from PartSelect and it arrived quicly in two days - this took only 10 minutes to replace.
All Instructions for the REX5634KQ1
1,711-1,724 of 1,724