REX5634KQ1 Roper Dryer - Instructions

Had a hard time at first trying to figure out how to place the pulley wheel that you place the belt around, it holds it in place so to speak, was getting very frustrated came upstairs went on line to your web site and lo & behold there was a video on how to do it, I watched that video (thanks Steve) and went back down cellar and had the belt on in less than 5 mins and everything is working fine. Thanks for all your help Dan

This is my second repair using your parts. There was a problem with the electrical of the house that was also causing the dryer to fail. Other than that, I learned a great deal the first time around about my dryer the first time I order parts from you. It was easy to fix the dryer back then. Now that I have the electrical and the dryer fix so easy I have a wife that is drying clothes like a maniac. Thank you; Juan from Ocala, Florida.

watched partselct.com how to video and nothing to it unplugged dryer, pull out from wall an disconected vent hose, take out the nine screws and two in element then it will slide down and out pull off wires and replaced.It`s EASY ,,

Replaced Themostat

Take out all the parts and see the video to put the new parts and is set thanks

The repair on replacing the clothes dryer belt went great. Not only did Part Select send me the correct belt at a great price .. the helpful hints that other people gave was most helpful. The only glitch was when I was pushing the tensioner wheel to get the belt around the pulley it slipped and the spring came off. The instructions/tip of taking the drum out and how to replace it came in handy when I had to get the spring back into place. The belt finally went on but there was a slight twist in it by the tensioner wheel. Again the tip I got with my e-mail helped as I manually turned the drum and was able to right the belt. Kudos to the tips I received and the confidence I could do the job myself!!!!

It was very easy. I figured out that I needed a new heating panel, entered my model number and voila, 1 1/2 days later it was on my porch. I used the video on the Parts Select website and was able to install it myself, very easy. Saved myself time & money, a lot of money.

push in on clips on front top at seams apx 2-3 inches from both sides. lift lid lean it back. remove door switch. remove front panel. remove old belt. replace with new belt lifting drum slightly to get around drum rib side down. reach in and push tensioner down to the left place belt around pully and over tensioner relase gently put all item back together.

Removed the eight 1/4" screws securing the back panel of the dryer, removed the electrical connections, and the two screws holding the heating element. Swapped the plastic switch to the new element, and reassembled. The repair took less than ten minutes and the dryer works perfectly.

Tested the old thermal cut off with multimeter, and it was defective. Replaced it using the schematic provided.

Queried the Internet for my model number of dryer. Found Part Select web site. Went to the site and entered my model number again. Found a list of common problems and my particular dryer problem was listed. Only two possibilities - thermal fuse or timer. Studied the diagnostic criteria for thermal fuse and that seemed to fit my situation. Watched the video of how to replace the thermal fuse. After watching the video, I was convinced I could fix the dryer. Ordered the thermal fuse and it arrived in about 2 days. Followed the instructions previously viewed on the video and replaced the thermal fuse. Success!! Mission accomplished!! I felt great that I had done this by myself with help from Part Select. A service call from a repair establishment would have cost about $130.00. I fixed my dryer for about $9.00 plus shipping cost of about $7.00. And I didn't have to wait for two weeks for a repairman to show up and occupy my whole day. I forwarded the Part Select link to all of my friends and relatives and told them to use Part Select for their repair needs. Awesome web page and service! Use them!

I first pulled the drum and turned on the dryer. The igniter never turned on. So I unplugged the dryer from the outlet and measured the resistance of the igniter, which was ok. I pulled the back panel and checked the thermal fuse, which was open. I also pulled the lint system plenum off of the unit, which was clogged with lint. This probably caused the thermal fuse to overheat. I cleaned out the lint collection system, replaced the thermal fuse and re-installed the drum. dryer is now working fine.

You send me a link to a video It was excellent 15 minute job. now my dryer works like the first day I got it. all I can say is thank you excellent part excellent communication extremely fast shipping. what more can I say I am 100 percent satisfied.

As per video instruction that came with the email order conf

Watched Youtube video first then followed directions included with belt. Very simple and easy to follow.