REX5634KQ0 Roper Dryer - Instructions

took the back off looked at the element found a coil broken.found model number and ordered part. part came in fast, I was surpized when it came in within 48 hours had a little trouble disconnecting the wires, I didn't know how gentle to be.put the element back in place. Put the back on and yea it worked. the reason I decided to do it myself is because I spent 98 dollars with an appliance person about a month earlier putting the belt back on. I thougkt I was going to have to buy a new dryer. so it was worth the effort to look into fixing it myself. Rose in Texas

Used repair video as guideline, I did not have their lab conditions to work in and by no means a clean machine. Also I had a two part front panel vs. single as in video, so disassembly and reassembly were OJT."on job training". Video was however very usefull in locating problem, getting correct part and accomplishing the repair. Saved $$ and machine is now working properly again. Am saving this web-site to my favorites list.

Shut off power. Opened the top, removed 2 screws one on each side of front door. Opened clip and removed switch and unplugged wire. Removed front door by lifting it up off bottom clips. Removed the drum and checked the drum support wheels, idler and motor pulley. Shop vacuumed everything to get all the lint, dirt and spider webs out. I was lucky, my idler has a spring, so I cut a small piece of wood and put it between the exhaust pipe and the idler to keep it out of the way. I replaced the drum, slipped the belt over the drum and centered it over the pulley (old belt mark on the drum). I reached under the right side and put the belt around the motor pulley and carefully removed the wood holding the idler, turned the drum by hand to check it. Set the front door back in place, plugged the wire back in, put the switch back in the clip, put the 2 screws back in, turned the drum by hand again. OK! Turned power back on and started the dryer. Total new belt installation time was under 10 minutes.

Pulled back off the dryer replaced heating element following the directions on PartSelect.com Thank you for being a great website. You also helped me with my 10yr old Washer two months ago. i especially love the how to videos.

I opened up the instrument panel box using philips screw driver and found the repair instructions. Followed the symtom diagnostic page and found that if the machine can be turned on but motor not working then check thermal fuse or motor. Next, I unplugged the appliance and remove the back panel to locate where the thermal fuse and other parts per the diagram in the repair instructions. Using a volt meter, I removed the electrical plugs to the thermal fuse and check resistance (a 1 on the volt meter indicated that the fuse is open (or burned)). Removed the thermal and checked for part number and looked up the model and parts number on the internet. Took a chance and ordered the part. When the order arrived 3 days later, I just simply replaced it and put everything back to where they were. Hooked up the power supply and turned on the dryer. It works again!! One thing I found was that I needed to clean the air pipe since it was totally clogged and probably caused the machine to overheat and burn out the fuse.

Took the old part off and replaced it with the new one.

pretty simple fix not much to it. If you are familiar with electrical work a dryer is just about as basic as it gets. Thermal fuse was bad, swapped it out and up and running again. It took me longer to get the dryer pulled out and cleaned up, than it did to replace the fuse. Wow was it diry back there!

repair was simple

Very easy to installation,first belt has to go on drum and then through pulley,pulley go on it`s place ,need some pressure on pulley to instal it.Very easy.Thank`s for fast belt delivery. Richard

I followed the instructions on the repair video provided by Parts Select. Super easy!

Watched the video but realized my dryer was a little different removed bottom front panel to expose area to remove thermal fuse. Checked for continuity, found that there wasn't any. Ordered part and replaced it, fired right up!!

Ordered heating element and follow instructions provided by PartSelect.com - The video was very useful. I previously called an appliance repair service for diagnostic and paid $60. The technician gave me an estimated cost for repair including the part would cost $340. which I did not want to spend so I went to the internet and found PartSelect web page and ordered the part. My husband was able to fix it with no problem. Your selling point is the video instructions. I will recommend your business to friends and family. Sincerely, Maria Ferrari

Ordered new rollers from PartSelect. I followed the video to replace the rollers. Everything went well. The video did not show how to put the belt back on. I then went to replace broken belt and there was the way to go through the pulley. Works great with no noise. Just like new. Thank you

My husband who is in a wheelchair and his freind who had never worked on a dryer,watched the video online and boom! just like that it was fixed!Some nut told me it would cost too much to fix,To just get a new one!Boy am I grateful for you!Thank You.virginia.

First and foremost, PartSelect is awesome! I placed the order on a Monday afternoon with regular shipping, and I had the belt Tuesday evening. Total repair involved removing several screws to open the top and front of the dryer, then installing the new belt. Pay close attention to the the dryer seal - make sure this is completely set. This was a very, very easy repair, and it cost me less than $20 for part and shipping! Also, the video on the PartSelect site shows exactly how to make this repair, and was very helpful.