Models > REX5634KQ0 > Instructions

REX5634KQ0 Roper Dryer - Instructions

All installation instructions for REX5634KQ0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the REX5634KQ0
1,531-1,545 of 1,705
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The dryer just stopped working one day

  • Customer: Tobias from Glenside PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
To make sure the dryer didn't die catastrophically, I checked to make sure the timer, the light, and the push to start start switch and the door switch were still working. After they were diagnosed to be working properly, I unplugged the dryer and pulled it back from the wall so I would have enough room to work behind it. The first item you will need is the wiring diagram. If you do not have one, one can be obtained online by using your dryer brand and model number. The next thing you will need is a quality digital multimeter that measures resistance or continuity. The last thing you will need is a 1/4" nutdriver. The first thing you will need to do is remove the exhaust tube from the back of the dryer. The second step is to remove a small black plate located near a green ground screw. The 3rd step is to remove the large black cover on the back of the dryer. Once this is removed, you will need to locate the thermal fuse. The thermal fuse is a small component that has 2 blue wires connected to it. It is located on the housing where the steam from your clothes leads to the exhaust port. The first thing you need to do is disconnect the 2 blue wires. Once the wires are disconnected, set the multimeter to resistance. The unit of resistance is ohms and the greek letter omega is used. The red lead of your multimeter goes one metal tabe of the fuse and the black lead goes on the other one. If the multimeter measures 0. L ohms, then the fuse is bad and needs to be replaced. If the multimeter reads 00.00 ohms then the fuse is good and you have another problem. I hope these instructions were useful.

Would not turn on..even though timer and power on button were working

  • Customer: John from Poughkeepsie NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
The video help to give confidence to change out the components since they were so inexpensive and the alternative was to go out and buy a new dryer.. It was easy to remove the back panel off dryer (after unplugging from the wall of course). The two components were unscrewed, cables unattached using pliers and replaced. The faulty element was definitely an open thermal fuse. For some reason there was a 5 Ohm resistance when the cables were connected.. Which confused me at first as I thought the fuse was not blown. I guess there was some conductance across the cabinet body. Anyway after replacing the fuse and thermostat the dryer was back to fully operational. I think it now actually drys better than before but that may just be wishful thinking.

No heat

  • Customer: jennifer from deerfield IL
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Very easily replaced both parts. Works perfect!!

No Heat

  • Customer: Ave from Winchester CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
I took one piece off at a Time. Made sure that each wire went to the correct place. I felt so good as a woman to be able to fix a necessity in our House without having to call a repairman to fix it for us. We are 3 women in our New Home. Im 46 My life partner is 48 and Our Daughter 17. I can't tell you how thankful i am for watching your video on how to do it. Thanks Part select. Dena , Ave & Fe .

dryer not heating

  • Customer: eugene from cheshire CT
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I checked the thermal fuse for continuity and had none.ordered part arrived next day. I took a picture with phone to idenify wires. installed in a short time.dryer works like new

Dryer would not heat up, but ran.

  • Customer: Bart from Hillsdale NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Could not be any easier. For less than $20 and 15 minutes time, I couldnt be happier.
All that was needed is a nutdriver to remove a 1/2 dozen screws to take the back panel off. Then a phillips screw driver to remove the thermal fuse. Unplug 2 wires and then attach them to the new fuse. Put it all back together and done!. Working dryer.
PS: I had enough gas line and ducting connected to the dryer ,so thatt I was able to get behind it with out removing them. This may have taken another 15 min. if I needed to do this and two adjustable wrenches.

dryer would not start

  • Customer: Nancy from Camden ME
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I watched the videos associated with the parts. They were easy to understand and I could follow the steps without difficulty. I replaced both the cycling thermostat and thermal fuse. Separately, I also replaced the "push-to-start" switch. Dryer would still not start. I called the repairman. Problem turned out to be a loose wire that had shorted out in the electrical bar near the "push-to-start" switch. All parts I replaced are determined to be good and will be tried next time I experience the dryer "not starting".

Dryer would not start ( hit start button nothing)

  • Customer: Laura from Lindenhurst NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Unpluged dryer first! Diconnected the vent hose.Took out 9 screws out of back panel.1 screw for the thermal fuse disconnected the two wires. Put new one in connected the wires. Then took out 1 screw that held the thermostat in place took 4 wires off. Put new one in reconnected the wires. Vacuumed out the back. Put back panel on. Connected the vent hose, plugged the dryer in. Pushed the start button & started drying clothes. Very easy!

My dryer just suddenly wouldn't come on.

  • Customer: Walter from LaVergne TN
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I ordered the Thermal Fuse, as it appeared to be the problem. A friend suggested that as long as the price was fairly reasonable, I should go ahead and get two of them and keep one for later. I ordered/paid for two of them. I put the Thermal Fuse in, and when I attempted to turn the dryer on, it ran for about 5 minutes, at a very hot heat, dried the towels, and then would not come on again. I thought it had kicked the circuit breaker, but after checking, found it hadn't. I watched the youtubes.com again and found that there were three other parts that it could possibly be. I ordered them, and replaced all of them. One of them had 4 prongs but two on the new one. I left two wires off, and sure enough, it would not run. I borrowed an ohm meter, and found out my old part was still good, but that in the process it had blown the Thermal Fuse, of which I just happened to have an extra, and after installing it, it is now in perfect running order. The total repair was about $80-100, rather than a $75.00 bill for service and heaven only knows for the parts at the repairman's price! Thanks youtube, Parts Select and my friend for his advice! Walter

Dryer turned on and drum rolled. but no heat or igniter glow.

  • Customer: Victor from Bellport NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
My wife hates me because I keep repairing our appliances. The dryer and washing machine are now 21 years old and look like new. To replace these two parts, first check if the igniter is glowing at all when you turn the dryer on. To do this remove the access panel in front on the bottom. To remove it, slide a flat screw driver across the slot onto of the panel to locate the release clips. Depress the release clamps by sliding the screw driver on top and pull the panel forward. Now start the machine and see if the igniter glows. If not proceed to replace the Thermal Fuse and both thermostats. To do so, open the back panel of the unit. First disconnect power and vent. Unscrew and replace components which will be easily seen on the bulk head. Use a pliers to remove the contacts. Your machine will now last another twenty years and your wife will hate you as does mine:)

Did not heat

  • Customer: Richard from Hesperia CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Took the back cover off. Replaced fuse and put the cover back on. Worked great.

no heat

  • Customer: Tanimu from Mansfield TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I replaced both the Thermal fuse and Cycling Thermostat, both of which cost less than fourty dollars. just removed the back panel, and replaced the parts in less tham a minute. Replaced the back panel. Job done.

Dryer would start and run but no heat was produced.

  • Customer: andres from yucaipa CA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Watched several videos online and was suggested that the thermal fuse was bad, so i replaced it but no fix. So i checked the previews Q&A from other costumers and watched the videos on how to replace different parts. I first looked thru the peep hole on the bottom left part of the dryer and saw the igniter glow for about 10 sec every minute but no flame would start. So i replaced the igniter, the flame sensor, and the coils all at once. I know thats not the proper way to troubleshoot something but i was gonna take the drum out and everything so mind as well replace them all. Dryer works like new and dont have to listen to the wife complaint anymore!!!

Dryer stopped running

  • Customer: James from Malcom IA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I repaired this dryer after I did a little research online to learn about the thermal fuse. I took the back off the dryer and used the Fluke meter to test the thermal fuse for continuity. There wasn't any. I left the dryer disassembled and ordered the part. It arrived two days later. I installed it and reassembled the dryer in just a few minutes. It was a pretty simple repair.

Motor and Thermal Fuse Replacement

  • Customer: Bruce from Ellington CT
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
I actually found the repair to be quite easy. This dryer along with the washer are basic models and over 15 years old. I have replaced just about every part on these machines. The more "basic" the model; without all the bells and whistles and electronics, the easier they are to repair yourself. I used a YouTube video for this particular model for the repair. All the items you sent arrived in superb condition and delivered in just a couple of days! Absolutely fantastic and professional service bar-none! I would highly recommend your site to anyone looking for 1st rate products and unbelievable speedy service. I will be using you again for any and all repairs for my appliances. Thank you very much for the outstanding customer service. Kindest Regards, Bruce
All Instructions for the REX5634KQ0
1,531-1,545 of 1,705