Quick Question!

Have you ever purchased from PartSelect.com before?

Models > REX4634KQ1 > Instructions

REX4634KQ1 Roper Dryer - Instructions

All installation instructions for REX4634KQ1 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the REX4634KQ1
1,711-1,725 of 1,840
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The dryer just stopped working one day

  • Customer: Tobias from Glenside, PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
To make sure the dryer didn't die catastrophically, I checked to make sure the timer, the light, and the push to start start switch and the door switch were still working. After they were diagnosed to be working properly, I unplugged the dryer and pulled it back from the wall so I would have enough room to work behind it. The first item you will need is the wiring diagram. If you do not have one, one can be obtained online by using your dryer brand and model number. The next thing you will need is a quality digital multimeter that measures resistance or continuity. The last thing you will need is a 1/4" nutdriver. The first thing you will need to do is remove the exhaust tube from the back of the dryer. The second step is to remove a small black plate located near a green ground screw. The 3rd step is to remove the large black cover on the back of the dryer. Once this is removed, you will need to locate the thermal fuse. The thermal fuse is a small component that has 2 blue wires connected to it. It is located on the housing where the steam from your clothes leads to the exhaust port. The first thing you need to do is disconnect the 2 blue wires. Once the wires are disconnected, set the multimeter to resistance. The unit of resistance is ohms and the greek letter omega is used. The red lead of your multimeter goes one metal tabe of the fuse and the black lead goes on the other one. If the multimeter measures 0. L ohms, then the fuse is bad and needs to be replaced. If the multimeter reads 00.00 ohms then the fuse is good and you have another problem. I hope these instructions were useful.

Would not turn on..even though timer and power on button were working

  • Customer: John from Poughkeepsie, NY
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
The video help to give confidence to change out the components since they were so inexpensive and the alternative was to go out and buy a new dryer.. It was easy to remove the back panel off dryer (after unplugging from the wall of course). The two components were unscrewed, cables unattached using pliers and replaced. The faulty element was definitely an open thermal fuse. For some reason there was a 5 Ohm resistance when the cables were connected.. Which confused me at first as I thought the fuse was not blown. I guess there was some conductance across the cabinet body. Anyway after replacing the fuse and thermostat the dryer was back to fully operational. I think it now actually drys better than before but that may just be wishful thinking.

timer not working

  • Customer: ralph from santa rosa bch, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
remove accese panel remove timer place wires one at a time remount timer

Timer would not advance

  • Customer: pamela from ocean springs, MS
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I unplugged dryer. Took the top back plate off. Removed the dial and the screw on the front. Removed the two screws from the back and pulled the timer out. Pulled wires off one at a time and put them on the new time in the exact place and screwed it in. Put the screw and front plate on and plugged dryer in and checked it. It worked. Unplugged dryer again and put back plate back on. Done

Noise due to rollers and shafts worn

  • Customer: Frank from Leechburg, PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Removed front and back covers on dryer, screws on top and down one side to spread cabinet to remove drum,removed blower cover to get access to shaft nut on that side. The other is accessible. I found that both shafts can bethe longer of the two that were sent. The shorter shaft is too short and needed to be modified to let the roller come outward to lay in the grove in the drum. I will get a longer shaft and replace it.

Dryer made kind of a grinding noise when it started. A repair technician looked at it and said it needed new drum support rollers and shafts.

  • Customer: Janis from Lakewood, CO
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I followed the instructions on the Part Select website for drum support rollers and shaft. The videos were great! (There wasn't one for the right side shaft but I could extrapolate from the other instructions.) The hardest part for me was releasing the dryer top - the video made it look so easy but it took me a long time to get the little clips to release with the putty knife. Also, tightening the new right side shaft required the help of another person as my arms are not long enough to hold the shaft with pliers while I tightened the nut in the back of the dryer (and I did have to remove the back cover for this shaft). I would recommend to anyone even a little bit handy to attempt a repair following part select's videos.

The dryer sounded like a thrashing machine.

  • Customer: Robert from Indiana, PA
  • Difficulty: Really Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
I consulted the internet and found Part Select and use online repairman to diagnose the problem and found the roller solution with the parts, video and parts illustration. Sure enough, the left roller hole was worn and egg shaped. I ordered the parts on a Wednesday afternoon. While I waited, I got all the lint from the bottom pan, motor, and around the burner cleaned out and ready for the new parts. The parts arrived Friday morning and I installed them and put the dryer back together before noon. The dryer works and sounds like a new machine. Now I am ready to attack the squeaky fan motor in the freezer compartment of our refrig.

Dryer was making loud noises.

  • Customer: Ed from Omaha, NE
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I had to opcn up dryer, remove drum and replace worn parts.

loud squealing when running

  • Customer: Michael from Easton, MD
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the video provided by PartSelect. It pretty much went exactly like the video said it would. I was pretty sure the belt or idler pully must be the culprit, but I didn't even know how to open the thing up until I saw your video. I would likely still be putting up with the squealing without that video. Now the dryer is nice and quiet. -Mike

Dryer made a loud noise while drying clothes

  • Customer: Hermelinda from Merced, CA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
My husband first had to determine the problem he opened up the back of the dryer (Maytag) model. He determine one of the drum support rollers and bracket needed to be replaced it was really worn out. Once he installed the new parts the dryer no longer made any noise. :)

My daughter threw a heavy wet comforter into the dryer and the tri-ring sheared off.

  • Customer: Joe from St. Louis, MO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.

drum rollers worn out, making kocking noise

  • Customer: Nita from Clarkston, WA
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
just replaced the rollers with the new ones. The trouble was getting the belt around the drum again, but it all worked out and the dryer is running good

Belt & clip where both broken

  • Customer: Amy from Seagrove, NC
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
My 11 year old son and I ordered the parts we needed. Saw the GREAT easy installation video, It even was attached to my confirmation. After the parts got here him and I easily took off the old belt and clip, installed the new ones (after watching the viedo again) and we where done. You would have thought we fixed the space shuttle or something because we both smiled all day. My son also told every one that he and his mom fixed the dryer all by ourselves. Costed me only $40 dollars for the parts. I couldn't have even called a repair man out there for that. Thanks soo much.

Squeaky Idler Pulley

  • Customer: Mitchell A. from Hampton, NH
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the video that showed how to do the repair. I did exactly what I was shown on the video, and everything worked the very first time ! It was GREAT ! No more squeaking idle pulley !

dryer was loud when in operation

  • Customer: daniel from saint charles, MO
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
actually your site was very helpful in describing each part that i chose to replace. one helpful hint to someone when installing the dryer pulley is to use the parts box to hold up the drum when installing.it seemed to be the perfect size. great site!
All Instructions for the REX4634KQ1
1,711-1,725 of 1,840