Models > REX3514RQ0 > Instructions

REX3514RQ0 Roper Dryer - Instructions

All installation instructions for REX3514RQ0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the REX3514RQ0
1,516-1,530 of 1,606
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

was not drying

  • Customer: Barbara from Woodland Park CO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Socket set
  • 0 of 0 people found this instruction helpful
took of the back , took out the drying coil ,put the other in , but back on . now it works saved alot of money. love it. Thank you parts select.

Dryer not heating up

  • Customer: anne from grand rapids MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
This has happened several times to my KitchenAid dryer. It cost more than $100 to bring someone in to repair. Fortunately, I saved my bills and saw the part "thermal fuse" listed. I researched that and found your website. I couldn't believe how easy it was to fix. The part cost less than $15 and the diagrams you provided were a big help. I was about to purchase a new dryer, easily $500. Your site saved me a bunch of money. How I fixed? Unscrewed the back panel of the dryer. Found a part that resembled the part you sent me. Slipped it out. Put the new one in...that is it. I also figured that one reason the part keeps burning out is because my duct has to bend to get to the outside vent. The obstruction probably causes the dryer to overheat more often than not. I pulled the dryer 6 inches more away from the wall to see if that helps. My fuse was going out about every 2 years.

Dryer would not turn on.

  • Customer: Cassondra from Weaverville CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Was working fine one load and not the next. I remembered we had used this site for our dishwasher so gave it a try. Went with most common problem first. Ordered Sun rec'd Tues. Took longer to vacuum the back of dryer then it did to replace the fuse. Cost less than 30 bucks including shipping. Video was cool too.

dryer wont start

  • Customer: roosevelt from lilburn GA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
i still cant get it to start i keep having that 06 code revision after i ran the diagnostic i replace the thermistor right after that the dryer start but only dry one load and wont start again then i replace the thermal fuse still not working i order the door switch hopefully that might do it

Dryer wouldn't start.

  • Customer: Barry from Cincinnati OH
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Previous consumer help advised to check the Thermal Fuse. A quick check using an ohm meter or simply connecting the leads together, confirmed that the Fuse was open and bad. The other essential item is to clean & vacuum all lint from all other dryer parts on the top, drum & back of the dryer. Be sure to also perform a check of the Cycling Thermostat, located near the Thermo Fuse. This is not a difficult repair. Just be sure to disconnect the 220 V and the circuit breaker. A $9 fuse was better than the cost of a repairman or new dryer. Barry Burke, Cincinnati, Ohio.

Worn/Broken Thermal Fuse

  • Customer: Donald from Lake Elsinore CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Removed the old fuse and replaced with the new fuse. Of course, I had to remove the back of the dryer but very easy and the cost was less than $20.00. Definitely worth it because we did not have the money for a new dryer. PartSelect.com is awesome!

no heat

  • Customer: jacqueline from lackawanna NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
downloaded video

Dryer not getting hot

  • Customer: Donald from Ellington MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Followed the instructions provided by Parts Select and it was very easy and quick to fix !! Thanks Part Select for everything!!

Dryer tumbler runs, but no heat

  • Customer: Tim from Palmdale CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
At first I thought it was the ignitor, so I replaced it. No luck there. Next I went to the Part Select web site...that showed that the Thermal Fuse was the cause of this symptom 45% of the time. I installed the fuse and now my dryer is working!

Dryer overheated and thermal fuse blew.

  • Customer: Calvin from Klamath Falls OR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
removed back cover and with unit unplugged, removed one wire from each device (thermal fuses and switches) and measured with multimeter. Found thermal fuse open. Removed and looked up and ordered part. Installed fuse and buttoned er up and all good. Hardest part was putting the exhaust hose back on the floor outlet!

My dryer would run, but with no heat.

  • Customer: Daniel from Gastonia NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
After researching and reading other reviews on Partselect.com, I watched the videos on doing the repairs. I purchased the parts from partselect. I happy to receive them before the expected delivery date. Before the part arrived, I followed the recommendation on the videos and vacuumed out all the accumulation of lint. When the parts arrived, I followed the instructions on the videos. I replaced the parts. I put the cover back on and plugged in my dryer. It works great! I estimate a savings of approximately $3-400.00. I also felt good that I was able to do it on my own. I am definitely impressed with Partselect! Thank you so much!

Dryer wouldn't start

  • Customer: James from Bernardsville NJ
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Used video of PartSelect guy on YouTube to diagnose bad thermal fuse with multimeter. Removed back panel of dryer with nutdriver, removed thermal fuse, found no conductance across terminals. Ordered new part. (It arrived very quickly!) Put in new thermal fuse, replaced back panel. Shortened flexible vent tube so there would be fewer bends. Dryer works now.

Dryer would run, but there was no heat going to the unit

  • Customer: Rachel from Davenport IA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
It could not have been easier, thanks to the video displayed when I ordered the part. It was as easy as removing the back of the dryer, taking out the old fuse and putting in a new old. I have NO repair experience, so little I had to borrow the nutdriver from the maintance man at work. I was more then a little leary to try this repair on my own, but decided it was worth all the money I would save not having to call a repair man for my dryer. Sure glad I did I will continue to attempt more repairs on my own.

Element was intact but no heat was present.

  • Customer: Jean from Greenacres FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Did all according to the online demonstration and everything was as easy as 1-2-3. The dryer works like new again.

stopped making heat

  • Customer: daniel from Centereach NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
i replaced the two sensors in the heating element which were very clear in your diagram and it worked perfectly
All Instructions for the REX3514RQ0
1,516-1,530 of 1,606