Models > REX3514PQ0 > Instructions

REX3514PQ0 Roper Dryer - Instructions

All installation instructions for REX3514PQ0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the REX3514PQ0
1,201-1,215 of 1,626
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

I had to spin drum for dryer to start, bad start winding on motor, not sure if the problem could have been fixed by replacing the motor contactor. I could not find a part # for just the contactor.

  • Customer: Dale from Joanna SC
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
You have to disassemble the dryer. I looked up how to on youtube.com. I am grateful that people take the time to record the steps in which to do just about anything. Disassembled and ordered motor and fan, damaged fan taking it off, got it in in just a couple of days, installed motor, fan and drum, tested before complete assembly. Works great. Thanks

Broken Blower Wheel

  • Customer: James from Mosca CO
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Remove the back panel, then remove the housing around the blower, just slide the housing of to the side, you don't have to take it completly of the machine. Remove the top, and remove the front until you can get to the blower motor. Cut the blower wheel plastic down to the metal nut with a fine blade in a recipricating saw, used a bi-directional broken stud remover socket on the nut that was at the center of the blower wheel and large slip joint plyer on the other end of the shaft. Replace the wheel and put back together. It took about as much time to gather up the tools as it did to fix it.,

Washer/Dryer would not start

  • Customer: James from Salt Lake City UT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Socket set
  • 0 of 0 people found this instruction helpful
Neither the washer or the dryer of the stacked unit would start. The website suggested that one of the causes could be the thermostat. I ordered a replacement that arrived quickly. Swapping the part only took minutes, and it started just fine.

way too hot

  • Customer: Thomas from Holly Hill FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
removed back replaced thermal fuse and adjustable thermostat limit dryer working fine now cost of parts 54.00 new dryer would have cost 450.00

Dryer Not Drying Clothes on first cycle

  • Customer: Thomas from Glenpool OK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Took the back off the dryer. Disconnected the old thermostat and installed the new thermostat. Connected the back of dryer. Put in a load of clothes to dry and the clothes were dry on the first try. Works like a new dryer. Saved a lot of money not having to buy a new dryer when all I had to do was replace some old parts.

no heat

  • Customer: Dan from Thomasboro IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Socket set
  • 0 of 0 people found this instruction helpful
ordered wrong limit switch had to reorder right switch and decided to replace the heater element as well. works fine now

A lot of noise coming from the front of the dryer.

  • Customer: David from Kingston MA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
After removing the front of the dryer it was evident that the blower boss had broken where the motor shaft comes through and is attached. I removed a few more parts to make the blower more accessible and removed it. I then machined a new boss and attached it to the blower and reinstalled it.I then did a quick continuity check on the three thermostats since the dryer was already apart.I discovered one was faulty and ordered a new one from you.That repair took all of five minutes.The irony of the whole thing is that while I was ordering the thermostat from you,I asked out of curiosity,if the blower was still available. As it turns out it still is but the new machined part worked out great and the dryer was back up and running in no time.

Thanks again,
Dave

low or no heat

  • Customer: charles from bryan TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed back cover of entire dryer.The thermostat was accessible from that point(Just as diagram showed), removed two wires from thermostat, removed thermostat & replaced with new thermostat & plugged 2 wires back in just as instructions indicated. Very simple,15 minute job. I will certainly use again for any appliance repairs.

No Heat

  • Customer: Melissa from Tampa FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
After replacing the heating element and the thermal fuse, with no success, these parts completed the full electronic components for the heat system. I'm not sure which part was the culprit, these three additional parts fixed the dryer. The repair was fairly simple and the videos for the repair were extremely helpful. The only suggestion that I have is to be sure which connection blade you cut off on the provided wire to replace as shown in the Thermal Cut-off Video. On my model, one connection blade is slightly larger than the other. If you cut-off the wrong end, you will create a little more work for yourself.

Stopped drying....little heat in drum but clothes not dried after 45 min.

  • Customer: Jim from Simi Valley CA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Not knowing exactly what needed to be replaced I used the in-site questionnaire and followed through to problem and then ordered the first two items suggestions. Turned out the Heating Element Connection Wire Kit was redundant and not needed as the Cycling Thermostat included two such wire kits. I watched the video on the site and that gave me a fairly good idea how to proceed. I removed the back panel, lot of small screws, and then the Thermostat was easy to see. There are two similar looking parts but after closer look only one matched the new thermostat. Super easy, just remove wires and old thermostat and replace with new item and then before actually reinstalling back panel I put a load of damp clothes to dry. Half hour later...Wallaaa...problem resolved. Good luck with your fix. Oh, there is a sheet referencing to set the new thermostat if needed to a certain limit, however using old thermostat with its embedded model # found that factory setting for new one was fine. So, no need to reset.

not enough heat to dry clothes

  • Customer: James C. from Cobbs Creek VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
always unplug from outlet first, unscrewed the back off and pull off the wire from cycling thermostat ,take the two screw out that holding it in place and replace the new one .Very simple and easy. Thank you for the easy step by step video to complete this repair. James

on-off switch

  • Customer: vincent from lesterville MO
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
took off the back part with nut driver removed switch assembly by pressing down with a little pressure and it snapped out the new was a little different but worked on installing this was an easy assembly. just do things in reverse when finished just plug in electric and push switch to turn on. very easy to install.

Loud humming noise then motor would stop

  • Customer: Clarke from Lynnwood WA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
The dryer would make a loud humming noise and the seize up. I would reset the breaker and the dryer would run briefly and then seize up. I opened the dryer and cleaned out all the lint on the motor but it did not help. I spun the motor shaft and felt like a bearing inside had failed. I watched Steve in the video-he was awesome and made it all simple- and ordered the correct parts. I decided to replace the rollers, belt, and pulley as well as the motor. The repair is very easy-and worth it- EXCEPT one piece of advice. BUY the blower fan that attaches to the motor. Mine did not come off easily like in the video. The plastic shaft deteriorated under pressure from the wrench. I was forced to use a heat gun to melt/then cut the blower fan from the motor. It was not easy but don't let it deter you from the repair. I used a table vice but never could remove the remanents of the blower fan shaft from the motor. The repair was a snap after that. Great site for parts and help.

dryer was loud when in operation

  • Customer: daniel from saint charles MO
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
actually your site was very helpful in describing each part that i chose to replace. one helpful hint to someone when installing the dryer pulley is to use the parts box to hold up the drum when installing.it seemed to be the perfect size. great site!

loud squealing when running

  • Customer: Michael from Easton MD
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the video provided by PartSelect. It pretty much went exactly like the video said it would. I was pretty sure the belt or idler pully must be the culprit, but I didn't even know how to open the thing up until I saw your video. I would likely still be putting up with the squealing without that video. Now the dryer is nice and quiet. -Mike
All Instructions for the REX3514PQ0
1,201-1,215 of 1,626