Quick Question!

Have you ever purchased from PartSelect.com before?

Models > REX3514PQ0 > Instructions

REX3514PQ0 Roper Dryer - Instructions

All installation instructions for REX3514PQ0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the REX3514PQ0
1,186-1,200 of 1,626
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

timer runs but dryer wont start (fuse was not closed)

  • Customer: Glen from Covington, LA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Took off the backplate of dryer, replaced fuse, done.

Replace Drive Belt

  • Customer: William from Marlborough, CT
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
What a pain in the butt to route the belt thru the tensioner! There's room for only one hand in there. The guys who do this for a living must have some secret. My solution was to drill a 3/16 hole thru the side, make a j-hook from 8-32 threaded rod, use that and a wing nut to pre-load the tensioner, route the belt, then slowly back off the wing nut until the belt was tight. It works. . . .

Dryer would start and run but no heat was produced.

  • Customer: andres from yucaipa, CA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Watched several videos online and was suggested that the thermal fuse was bad, so i replaced it but no fix. So i checked the previews Q&A from other costumers and watched the videos on how to replace different parts. I first looked thru the peep hole on the bottom left part of the dryer and saw the igniter glow for about 10 sec every minute but no flame would start. So i replaced the igniter, the flame sensor, and the coils all at once. I know thats not the proper way to troubleshoot something but i was gonna take the drum out and everything so mind as well replace them all. Dryer works like new and dont have to listen to the wife complaint anymore!!!

Broken Belt

  • Customer: gary w from Saint Louis, MO
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Pop off the top , Then one screw holds each side . slide belt around drum and then preload tensioner as per instructions . Simple!

Clothes were not drying, no heat in dryer.

  • Customer: Maxwell from Belen, NM
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
The video is right on. You can't go wrong, and I don't consider myself a handyman at all.

Dryer not drying clothes completely

  • Customer: Greg from Gilbert, AZ
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Super easy repair. Just removed the back panel, took out the old heating element, plugged in the new one and put it back together. I had also replaced the element in a similar Whirlpool dryer in one of my rental properties a few months ago and it was just as easy. Between the two repairs I saved between $200 and $300 in repair labor. PartsSelect always has the parts I need in stock, ships quickly and their installation videos rock. I have also used them for repair parts on microwaves & refrigerators in the past. Excellent vendor. Highly recommended.

heating element

  • Customer: vincent from lesterville, MO
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
viewed the video that was posted on your web site it was very use full in helping me to repair the machine. it was not difficult to take out and reinstall.i like your quick response on shipping parts. I am very satisfied.

Did not heat

  • Customer: Richard from Hesperia, CA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Took the back cover off. Replaced fuse and put the cover back on. Worked great.

Dryer not heating

  • Customer: Fred from Silver Springs, FL
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed the back pannel of the unit and then removed the heating element. Installed the new one and replaced one burnt wire. Have done several of this type of repair over the years.

My dryer just suddenly wouldn't come on.

  • Customer: Walter from LaVergne, TN
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I ordered the Thermal Fuse, as it appeared to be the problem. A friend suggested that as long as the price was fairly reasonable, I should go ahead and get two of them and keep one for later. I ordered/paid for two of them. I put the Thermal Fuse in, and when I attempted to turn the dryer on, it ran for about 5 minutes, at a very hot heat, dried the towels, and then would not come on again. I thought it had kicked the circuit breaker, but after checking, found it hadn't. I watched the youtubes.com again and found that there were three other parts that it could possibly be. I ordered them, and replaced all of them. One of them had 4 prongs but two on the new one. I left two wires off, and sure enough, it would not run. I borrowed an ohm meter, and found out my old part was still good, but that in the process it had blown the Thermal Fuse, of which I just happened to have an extra, and after installing it, it is now in perfect running order. The total repair was about $80-100, rather than a $75.00 bill for service and heaven only knows for the parts at the repairman's price! Thanks youtube, Parts Select and my friend for his advice! Walter

No heat for electri8c dryer

  • Customer: Katherine from Michigan City, IN
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Wrench set
  • 0 of 0 people found this instruction helpful
Got on line for video repair.Ordered the part through Whirlpool parts. They told me the part that was needed.Took dryer apart, kept parts together & labeled so I knew where to put back. Replaced the heating part & put everything back in place. Turned dryer on. Worked very well And I had lots of heat. Was so happy. I am a 70 year old widow. It took me a while because I didn't have proper tools but had a few that would work. It was really quite easy and the video on the repair was amazing well done. Thank You Whirlpool for all your excellent advice..Part came in very Quickly..

Drum stopped turning

  • Customer: james from blue point, NY
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
After removing the back, I realized I absolutely did not know what I was doing. I went to google put in my model number, and went to your web page. The rest is history. Went to the video watched it and went back to the dryer and after cleaning up the back, put it back and removed the top and front as per video. The parts came in a few days and replaced the belt and idler arm n about 2 min. I am not kidding. The wife held the drum while I put the front back on. One thing I could not separate the door switch so I just unscrewed it from the fron panel. The dryeris 20 years old, and your web page will put the Maytag repairman on the unemployment line.

Dryer would not heat

  • Customer: Garth from Summerfield, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
At first I thought that the dryer had seen its better days so I thought that it would buying time, at least $350.00 to get a replacement , but after that shock I was tempted to see what I could find on GOOGLE. There it was PARTSELECT giving me what was wrong and what to do and when I found out how easy it was to fix I immediately ordered the replacement element and it was delivered to my home two days earlier than expected. I had old element removed and new installed very quickly. You all were great with the remove and replacement info along with the fast shipping. Thanks again.

Dryer would run but very little heat

  • Customer: Fernando from Fort Worth, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Watched the repair video once, it was real informative and easy to follow. The repair took about 30 minutes to complete. The video went step by step. Had no problems what so ever. Made the reapir and turned the dryer on and let it run for a few minutes and once again had all the heat I needed to make it operate correctley. I recomend that once you see your dryer is not dring your clothes like it once did, replace these parts. I let this go on for a year thinking my wife was putting way to many clothes in the dryer. It was not that at all. No telling how much money we could have saved on our electric bill by replacing these parts sooner. $30 dollars for the parts, I bet we spent that much a week on extra drying cycles. What used to take 2-3 cycles to dry now only takes one cycle. Runs just like it did when we purchased it.I will buy from this site again, easy to use all the information you need to make the repair and prompt shipping. Awesome site.

Dryer made kind of a grinding noise when it started. A repair technician looked at it and said it needed new drum support rollers and shafts.

  • Customer: Janis from Lakewood, CO
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I followed the instructions on the Part Select website for drum support rollers and shaft. The videos were great! (There wasn't one for the right side shaft but I could extrapolate from the other instructions.) The hardest part for me was releasing the dryer top - the video made it look so easy but it took me a long time to get the little clips to release with the putty knife. Also, tightening the new right side shaft required the help of another person as my arms are not long enough to hold the shaft with pliers while I tightened the nut in the back of the dryer (and I did have to remove the back cover for this shaft). I would recommend to anyone even a little bit handy to attempt a repair following part select's videos.
All Instructions for the REX3514PQ0
1,186-1,200 of 1,626