Quick Question!

Have you ever purchased from PartSelect.com before?

Models > REX3514PQ0 > Instructions

REX3514PQ0 Roper Dryer - Instructions

All installation instructions for REX3514PQ0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the REX3514PQ0
1,171-1,185 of 1,626
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

A lot of noise coming from the front of the dryer.

  • Customer: David from Kingston, MA
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
After removing the front of the dryer it was evident that the blower boss had broken where the motor shaft comes through and is attached. I removed a few more parts to make the blower more accessible and removed it. I then machined a new boss and attached it to the blower and reinstalled it.I then did a quick continuity check on the three thermostats since the dryer was already apart.I discovered one was faulty and ordered a new one from you.That repair took all of five minutes.The irony of the whole thing is that while I was ordering the thermostat from you,I asked out of curiosity,if the blower was still available. As it turns out it still is but the new machined part worked out great and the dryer was back up and running in no time.

Thanks again,
Dave

low or no heat

  • Customer: charles from bryan, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed back cover of entire dryer.The thermostat was accessible from that point(Just as diagram showed), removed two wires from thermostat, removed thermostat & replaced with new thermostat & plugged 2 wires back in just as instructions indicated. Very simple,15 minute job. I will certainly use again for any appliance repairs.

loud squealing when running

  • Customer: Michael from Easton, MD
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the video provided by PartSelect. It pretty much went exactly like the video said it would. I was pretty sure the belt or idler pully must be the culprit, but I didn't even know how to open the thing up until I saw your video. I would likely still be putting up with the squealing without that video. Now the dryer is nice and quiet. -Mike

dryer was loud when in operation

  • Customer: daniel from saint charles, MO
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
actually your site was very helpful in describing each part that i chose to replace. one helpful hint to someone when installing the dryer pulley is to use the parts box to hold up the drum when installing.it seemed to be the perfect size. great site!

Loud humming noise then motor would stop

  • Customer: Clarke from Lynnwood, WA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
The dryer would make a loud humming noise and the seize up. I would reset the breaker and the dryer would run briefly and then seize up. I opened the dryer and cleaned out all the lint on the motor but it did not help. I spun the motor shaft and felt like a bearing inside had failed. I watched Steve in the video-he was awesome and made it all simple- and ordered the correct parts. I decided to replace the rollers, belt, and pulley as well as the motor. The repair is very easy-and worth it- EXCEPT one piece of advice. BUY the blower fan that attaches to the motor. Mine did not come off easily like in the video. The plastic shaft deteriorated under pressure from the wrench. I was forced to use a heat gun to melt/then cut the blower fan from the motor. It was not easy but don't let it deter you from the repair. I used a table vice but never could remove the remanents of the blower fan shaft from the motor. The repair was a snap after that. Great site for parts and help.

Lould nosie from Drum Whells

  • Customer: FRANCIS from PHILADELPHIA, PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I watch and followed the three viedos that PartSelect emailed me and had a very easy repair job.

drum not turning

  • Customer: Tony from Greenville, IL
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Watched a video on utube and realized how easy this looked, took my dryer apart to see the belt broken in half and the idler pulley in pieces. Found Partselect on the internet and ordered my parts. Partselect was awsome, website was easy to navigate, ordered my parts and they were at my house the very next day and were the correct parts. Cleaned all the lint and dust out of the inside of my machine, installed new parts and put it back together. Works great and is still running strong. A service call, plus parts (with thier mark up) could have easily been $150.00 - $200.00 dollars. this repair was complete in about an hour and only cost me $37.50

Sqealing noise and extended drying time

  • Customer: Gregory from Casa Grande, AZ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Followed online youtube directiond to dissassemble dryer cabinet. Everything is readily accessible and belt and idler are easily installed. Comments from others express frustration at the instability of the idler pulley bracket. The key is to keep seating pressure on bracket until the belt is installed at which time the belt supplies continuous pressure to seat the bracket. The bracket is very stable so long as moderate force is applied to hold the brackett in the seat. The belt install is counter intuitive in that the ribbed side of the belt is installed in contact with the drum instead of the flat side. The readon for this is so the belt ribs seat in the grooves of the motor pully and provide greater friction. Flat side of the belt on the drum places the flat belt on the grooved pulley with much reduced contact area.

tumbler would not turn

  • Customer: LORRIE from ARNOLD, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I followed the video directions exactly as instructed and I had no problem doing the repair myself. And if I can do it being a woman with no help you can do it. Easy peasy~

Dryer had become REALLY noisy.

  • Customer: William from Dallas, TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
The PartsSelect video was great. I'm not sure I would have figured out the trick for opening up this dryer without it. After that the main problem was getting goop off of the drum support roller spindles. This took lots of solvent and elbow grease. I think this was the main source of noise. The oil had turned to something like partly dried glue. They were very hard to turn. The belt was intact but badly cracked. The idler probably could have been oiled and reused but I already had the part so I replaced it. Everything went just like the video. The dryer now hums along like a new one!

Dryer would run for approximately 8 mins, then shut off by itself. After about 20 mins, dryer would restart but stop on it's own within 8-10 mins. Motor was also noisy when it ran.

  • Customer: Terrence from Hotsprings, AR
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
Unplugged dryer, removed 2 screws under filter lid, removed filter, removed access panel on back of machine, removed blower motor housing, vacuumed all dust and debris from rear of dryer, turned dryer around and opened top of dryer using a small screwdriver to release the clips approximately 2" from either end, then securing top from falling by using bailing wire to hold it in place, disconnected door switch wiring harness, removed 2- 5/16 screws retaining front panel and removed front panel from dryer, removed drum from dryer, removed idler pulley from bottom of cabinet noting position of drum belt, vacuumed dust and debris from bottom of cabinet and around old motor, removed motor retaining clips rotated motor and removed wiring harness from motor. I then attempted to remove the blower wheel from the old motor and here is where the problem began. If your dryer has the original motor in it, or the motor has never been changed in it to the best of your knowledge, go ahead and order a new blower wheel with your other parts, because you will not get the old one off without destroying it. (this cost me several days to complete the repair). Do not use channel locks or vice grips to attach to the front pulley to remove or install the blower wheel... use 2 medium sized crescent (adjustable) wrenches otherwise the pulley will be damaged and you will have a lot of filing to do to repair it. (If you need to reuse the pulley. I did not as my motor and pulley was an exact replacement). I got the blower wheel off of the old motor by using a chisel and a hammer and cutting a hole around the attachment point on the motor shaft from the rear of the dryer. After this, the job was pretty easy. I put the new motor in the motor housing, put a crescent wrench on the pulley on the front of the new motor, then screwed the new blower wheel onto the motor from the back of the dryer. (remember, the blower wheel has left handed threads, so to install it you have to turn the pulley on the motor to the LEFT to thread it into the wheel.) After the blower wheel is installed and hand tight, use 2 crescent wrenches to tighten down on motor, (1 on the blower wheel hub where it is square, and 1 on the front pulley) rotate the motor down to the correct position for the wiring loom, (you want the wires to rest on the bottom of the cabinet when the job is complete)., then reinstall the motor retaining clips and attach wiring harness. At this point I installed new drum rollers, reinstalled the drum with a new drum belt, and replaced the idler pulley with a new one. (push the drum counter clockwise by hand a few times to center the drum belt and to make sure that the drum is on the drum rollers correctly). The front panel is now reinstalled being careful to make sure the clips on the cabinet engage the holes in the panel. Push back on the drum slightly and reinstall the 2- 5/16 screws to hold the front panel to the cabinet, then reattach the wiring harness for the door switch. Remove the bailing wire and close the lid. The blower wheel housing is then reinstalled, then reinstall the rear access panel. Reinstall the filter and the 2 screws under the filter lid. Plug in the dryer and your repair is complete. When a motor replacement is required, you are better off replacing the motor, blower wheel, drum rollers, drum belt, and idler pulley. I did and my dryer sounds and performs like a new one. My wife is absolutely delighted. I spent approximately $180.00 on the total repair while a new dryer would have cost me $600.00 + tax.

Drum stopped turning

  • Customer: james from blue point, NY
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
After removing the back, I realized I absolutely did not know what I was doing. I went to google put in my model number, and went to your web page. The rest is history. Went to the video watched it and went back to the dryer and after cleaning up the back, put it back and removed the top and front as per video. The parts came in a few days and replaced the belt and idler arm n about 2 min. I am not kidding. The wife held the drum while I put the front back on. One thing I could not separate the door switch so I just unscrewed it from the fron panel. The dryeris 20 years old, and your web page will put the Maytag repairman on the unemployment line.

The dryer was very noisy when running.

  • Customer: Jared from Napoleon, OH
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Disassembled front & top of dryer, removed drum & replaced belt, idler pulley & one support wheel (which was the problem). Reassembled drum, top, & front of dryer. Tested good, much quieter.

Drum belt broken.

  • Customer: john from buffalo, NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Just like the video. Disconnect the lint shute. Pop the top lose. Disconnect the door switch. I actually took the hooks off an removed the entire lid. Took the two screws out and removed the front panel. (The OEM idler was a teflon half-moon so I think the abrasion was what caused the belt to fail.) Put the belt around the drum. Rolled the drum to check the seal overlap was proper. Installed the idler and wrapped the belt around the motor shaft. Put it back together. Would have been a little easier with a helper.

Dryer making squiling noise when on.

  • Customer: Jerry from Magnolia, TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
First I watched a instruction video online.. It made the job easy. I have done it before but I did not remember exactly how to proceed, After watching the video i knew exactly what screws needed to be removed and what tool I needed for each step. Anybody sees the video before tackling this job, they can't go wrong.
All Instructions for the REX3514PQ0
1,171-1,185 of 1,626