Models > REX3514PQ0 > Instructions

REX3514PQ0 Roper Dryer - Instructions

All installation instructions for REX3514PQ0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the REX3514PQ0
1156-1170 of 1530
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

dryer not heating

  • Customer: eugene from cheshire CT
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I checked the thermal fuse for continuity and had none.ordered part arrived next day. I took a picture with phone to idenify wires. installed in a short time.dryer works like new

Dryer would not heat up, but ran.

  • Customer: Bart from Hillsdale NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Could not be any easier. For less than $20 and 15 minutes time, I couldnt be happier.
All that was needed is a nutdriver to remove a 1/2 dozen screws to take the back panel off. Then a phillips screw driver to remove the thermal fuse. Unplug 2 wires and then attach them to the new fuse. Put it all back together and done!. Working dryer.
PS: I had enough gas line and ducting connected to the dryer ,so thatt I was able to get behind it with out removing them. This may have taken another 15 min. if I needed to do this and two adjustable wrenches.

low heat

  • Customer: charles from camden NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
removed back cover 9 screws , 2 screws on heating element and it pulled out ,3wiers and the new one went in. thermal fuse, was one screw and two wiers and I was done.

The dryer just stopped working one day

  • Customer: Tobias from Glenside PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
To make sure the dryer didn't die catastrophically, I checked to make sure the timer, the light, and the push to start start switch and the door switch were still working. After they were diagnosed to be working properly, I unplugged the dryer and pulled it back from the wall so I would have enough room to work behind it. The first item you will need is the wiring diagram. If you do not have one, one can be obtained online by using your dryer brand and model number. The next thing you will need is a quality digital multimeter that measures resistance or continuity. The last thing you will need is a 1/4" nutdriver. The first thing you will need to do is remove the exhaust tube from the back of the dryer. The second step is to remove a small black plate located near a green ground screw. The 3rd step is to remove the large black cover on the back of the dryer. Once this is removed, you will need to locate the thermal fuse. The thermal fuse is a small component that has 2 blue wires connected to it. It is located on the housing where the steam from your clothes leads to the exhaust port. The first thing you need to do is disconnect the 2 blue wires. Once the wires are disconnected, set the multimeter to resistance. The unit of resistance is ohms and the greek letter omega is used. The red lead of your multimeter goes one metal tabe of the fuse and the black lead goes on the other one. If the multimeter measures 0. L ohms, then the fuse is bad and needs to be replaced. If the multimeter reads 00.00 ohms then the fuse is good and you have another problem. I hope these instructions were useful.

Dryer wouldn't start

  • Customer: Michael from Glenburn ME
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Once again part select has come through for me. googled dryer won't start and a video on utube came up. typed my model number in on part select website and followed directions. was easy got part in three business days regular shipping. very pleased with this site.

Dryer not heating

  • Customer: Heather from Endwell NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
I watched your video that was on the page with the part and followed exactly what he did. Removed the back; removed the element after unplugging the cap. Determined that there was a break in the coil by inspecting it. Bought the new part and replaced it exaclty as shown in the video. SUPER EASY!Thanks for the video instructions! It saved me tons of time. I cleaned the vents while I was at it. They needed it. Just pushed the lint out with a swiffer duster.

Heating element stopped heating

  • Customer: joseph from lincoln NE
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I decided to repair it myself, and after ordering the part from partselect.com, and getting it very quickly I installed the heating element and, viola, the dryer works great again. All the info necessary for simple repairs is available online for most major applainces, and if you a little basic mechanical know-how, it isn't that hard. I just wish I would have just ordered the part from partselect.com right away!

no heat in dryer.

  • Customer: leo from Needville TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
watched the video. Removed old part, installed new one - as per video.pluged it back in and started drying clothes again!

Dryer wouldn't heat up

  • Customer: Richard from SPRINGVILLE AL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Watched the video on how to remove the heater element. Ordered new element and replaced the old one. Fairly simple after watching the video.

the dryer blows but dont get hot.

  • Customer: Billy from Bryan TX
  • Difficulty: Very Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
i repaced heating element and fues still dont get hot. so i took it to a repair place.

No heat when dryer ran.

  • Customer: Michael from Oak Ridge TN
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Heating element had 2 wire connections and 2 screws that held it in place and was easy to replace. Thermal fuse had 2 wire connections and 1 screw holding it in place. Over all, this repair took about 5 minutes to complete and the dryer works great again! Mike N.

Dryer timer was counting down but dryer itself would not start!

  • Customer: Armando from Hilmar CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Watched the video but realized my dryer was a little different removed bottom front panel to expose area to remove thermal fuse. Checked for continuity, found that there wasn't any. Ordered part and replaced it, fired right up!!

The appliance can be turned on but motor won't start.

  • Customer: LUAN from MILPITAS CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I opened up the instrument panel box using philips screw driver and found the repair instructions. Followed the symtom diagnostic page and found that if the machine can be turned on but motor not working then check thermal fuse or motor. Next, I unplugged the appliance and remove the back panel to locate where the thermal fuse and other parts per the diagram in the repair instructions. Using a volt meter, I removed the electrical plugs to the thermal fuse and check resistance (a 1 on the volt meter indicated that the fuse is open (or burned)). Removed the thermal and checked for part number and looked up the model and parts number on the internet. Took a chance and ordered the part. When the order arrived 3 days later, I just simply replaced it and put everything back to where they were. Hooked up the power supply and turned on the dryer. It works again!! One thing I found was that I needed to clean the air pipe since it was totally clogged and probably caused the machine to overheat and burn out the fuse.

no heat

  • Customer: Brian from Cinnaminson NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
pretty simple fix not much to it. If you are familiar with electrical work a dryer is just about as basic as it gets. Thermal fuse was bad, swapped it out and up and running again. It took me longer to get the dryer pulled out and cleaned up, than it did to replace the fuse. Wow was it diry back there!

Would not run

  • Customer: Janice from Yankton SD
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Ordered a thermal fuse . Very fast service (24 hrs)put the fuse in and is now working again
All Instructions for the REX3514PQ0
1156-1170 of 1530