Models > REX3514PQ0 > Instructions

REX3514PQ0 Roper Dryer - Instructions

All installation instructions for REX3514PQ0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the REX3514PQ0
1,141-1,155 of 1,606
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dryer would not start.

  • Customer: Carl from OFallon IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
I tried all standard tricks: checking circuitry, switches, etc. Then I read other submissions on your site, which suggested this thermal fuse was the culprit on almost 50% of cases. I got yours in 2 days, installed in no time, easy as pie. One caution: it will take an entire day if you forget to close the dryer door completely.

Clothes not drying

  • Customer: Sallie from Apollo beach FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I cleaned out the vent inside and out. I removed the hose and checked the heat output, there was none. I ordered the Heating element, and the fuse as it was cheap enough not to have to go in a second time. I used a nut driver to remove screws, installed new part. The hardest was removing a small part from the old element that is needed to be added to the new Element. I switched on dryer to check for heat then replace back panel. I don think it has ever worked this well. I was bought 5 years ago from an unused model home.

Ddryer was runing however not putting out any heat

  • Customer: Jerry from Inez KY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I first came to the internet to resolve what was wrong. After finding the video I thought was correct I started. I used my volt/ohm meter to check the thermal fuse as instructed on the video and that was the problem. I ordered the new thermal fuse from PartSelect late in the day and it was in my hands the next evening. With in 20 minutes the dryer was doing what it was suppose to do. The hardest part was getting the back cover of the crier off and that wasn't to bad.

My dryer just suddenly wouldn't come on.

  • Customer: Walter from LaVergne TN
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I ordered the Thermal Fuse, as it appeared to be the problem. A friend suggested that as long as the price was fairly reasonable, I should go ahead and get two of them and keep one for later. I ordered/paid for two of them. I put the Thermal Fuse in, and when I attempted to turn the dryer on, it ran for about 5 minutes, at a very hot heat, dried the towels, and then would not come on again. I thought it had kicked the circuit breaker, but after checking, found it hadn't. I watched the youtubes.com again and found that there were three other parts that it could possibly be. I ordered them, and replaced all of them. One of them had 4 prongs but two on the new one. I left two wires off, and sure enough, it would not run. I borrowed an ohm meter, and found out my old part was still good, but that in the process it had blown the Thermal Fuse, of which I just happened to have an extra, and after installing it, it is now in perfect running order. The total repair was about $80-100, rather than a $75.00 bill for service and heaven only knows for the parts at the repairman's price! Thanks youtube, Parts Select and my friend for his advice! Walter

Dryer would start and run but no heat was produced.

  • Customer: andres from yucaipa CA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Watched several videos online and was suggested that the thermal fuse was bad, so i replaced it but no fix. So i checked the previews Q&A from other costumers and watched the videos on how to replace different parts. I first looked thru the peep hole on the bottom left part of the dryer and saw the igniter glow for about 10 sec every minute but no flame would start. So i replaced the igniter, the flame sensor, and the coils all at once. I know thats not the proper way to troubleshoot something but i was gonna take the drum out and everything so mind as well replace them all. Dryer works like new and dont have to listen to the wife complaint anymore!!!

Did not heat

  • Customer: Richard from Hesperia CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Took the back cover off. Replaced fuse and put the cover back on. Worked great.

low heat

  • Customer: charles from camden NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
removed back cover 9 screws , 2 screws on heating element and it pulled out ,3wiers and the new one went in. thermal fuse, was one screw and two wiers and I was done.

Dryer wouldn't start

  • Customer: Michael from Glenburn ME
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Once again part select has come through for me. googled dryer won't start and a video on utube came up. typed my model number in on part select website and followed directions. was easy got part in three business days regular shipping. very pleased with this site.

The timer was working but the dryer would not turn on.

  • Customer: Henry from Rosebud TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
I replaced the Thermal fuse and this fixed the problem.

Motor and Thermal Fuse Replacement

  • Customer: Bruce from Ellington CT
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
I actually found the repair to be quite easy. This dryer along with the washer are basic models and over 15 years old. I have replaced just about every part on these machines. The more "basic" the model; without all the bells and whistles and electronics, the easier they are to repair yourself. I used a YouTube video for this particular model for the repair. All the items you sent arrived in superb condition and delivered in just a couple of days! Absolutely fantastic and professional service bar-none! I would highly recommend your site to anyone looking for 1st rate products and unbelievable speedy service. I will be using you again for any and all repairs for my appliances. Thank you very much for the outstanding customer service. Kindest Regards, Bruce

DRYER WILL NOT START

  • Customer: James from Swannanoa NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
1.Shut off power to dryer 2. remove back panel covers with 1/4" nut driver 3. use OHM meter to determine continuity at various thermal couples (3) and the one thermal fuse on the blower panel.. (this was the "bad "one in my case) 4. remove two wires and remove the one screw that holds fuse. did not have the model# for dryer, so I took the part# from the blown fuse and found it at PARTSELECT.COM.. they even showed an exact picture of the part I needed..ordered on Tuesday/arrived by FED X on Saturday...Reverse procedure to install..

Dryer would not run.

  • Customer: clifton from WESTMINSTER MD
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Follow instructions from online video supplied by Parts Select. Repair went very smooth!! Dryer started up and I am back in business. Thank You Parts Select!

Dryer stopped running

  • Customer: James from Malcom IA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I repaired this dryer after I did a little research online to learn about the thermal fuse. I took the back off the dryer and used the Fluke meter to test the thermal fuse for continuity. There wasn't any. I left the dryer disassembled and ordered the part. It arrived two days later. I installed it and reassembled the dryer in just a few minutes. It was a pretty simple repair.

Dryer would not heat up, but ran.

  • Customer: Bart from Hillsdale NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Could not be any easier. For less than $20 and 15 minutes time, I couldnt be happier.
All that was needed is a nutdriver to remove a 1/2 dozen screws to take the back panel off. Then a phillips screw driver to remove the thermal fuse. Unplug 2 wires and then attach them to the new fuse. Put it all back together and done!. Working dryer.
PS: I had enough gas line and ducting connected to the dryer ,so thatt I was able to get behind it with out removing them. This may have taken another 15 min. if I needed to do this and two adjustable wrenches.

The dryer just stopped working one day

  • Customer: Tobias from Glenside PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
To make sure the dryer didn't die catastrophically, I checked to make sure the timer, the light, and the push to start start switch and the door switch were still working. After they were diagnosed to be working properly, I unplugged the dryer and pulled it back from the wall so I would have enough room to work behind it. The first item you will need is the wiring diagram. If you do not have one, one can be obtained online by using your dryer brand and model number. The next thing you will need is a quality digital multimeter that measures resistance or continuity. The last thing you will need is a 1/4" nutdriver. The first thing you will need to do is remove the exhaust tube from the back of the dryer. The second step is to remove a small black plate located near a green ground screw. The 3rd step is to remove the large black cover on the back of the dryer. Once this is removed, you will need to locate the thermal fuse. The thermal fuse is a small component that has 2 blue wires connected to it. It is located on the housing where the steam from your clothes leads to the exhaust port. The first thing you need to do is disconnect the 2 blue wires. Once the wires are disconnected, set the multimeter to resistance. The unit of resistance is ohms and the greek letter omega is used. The red lead of your multimeter goes one metal tabe of the fuse and the black lead goes on the other one. If the multimeter measures 0. L ohms, then the fuse is bad and needs to be replaced. If the multimeter reads 00.00 ohms then the fuse is good and you have another problem. I hope these instructions were useful.
All Instructions for the REX3514PQ0
1,141-1,155 of 1,606