Quick Question!

Have you ever purchased from PartSelect.com before?

Models > REX3514PQ0 > Instructions

REX3514PQ0 Roper Dryer - Instructions

All installation instructions for REX3514PQ0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the REX3514PQ0
1,126-1,140 of 1,626
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

heating element burned out.

  • Customer: thylden from tampa, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
super easy. pull back cover, unplug and remove element. install new part. wire in power and overtemp sensor. replace back cover. done.

dryer belt broke

  • Customer: mary from wimberley, TX
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
ordered the part late sun. afternoon. arrives ups on tues.am. took dryer apart and replaced belt and up and running in about hour and half. works great. dyrer is about 25 yrs. old.

Drum rotated, but clothes were cold

  • Customer: Marc from Charlotte, NC
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I looked at the PartSelect youtube videos on washer repair and the exploded view drawing on the PartSelect web site. I removed the dryer heating element and confirmed the the coils were "open". Ordering was fast and easy. When the part arrived the next day, I installed the new heating element in a few minutes and it worked perfectly.

No heat

  • Customer: Shilane from Conway, AR
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Easy, took all screws out, took picture with camera phone of connected wires, removed part,and replaced part.

no heat, timer would not advance

  • Customer: christopher from rockhill, SC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Got parts in 2 days, fast and easy repair.

The drum quit turning

  • Customer: Paul from Bryan, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Sunday, the drum on the dryer quit turning. I could hear the motor running, so I guessed that the belt had broken. I jumped on the internet and searched for Roper Dryer parts and Part Select jumped up. Within 30 minutes, I had a new belt ordered. I received the e-mail with the how-to included and boy did it save me some hassel. I was prepared to do it all wrong until I saw the video. When the belt arrived, it took me longer to gather the tools I needed than it did to change the belt. Thanks

Dryer would not heat up

  • Customer: Tammy from Corona, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the video on You Tube posted by PartSelect for part #279838. The thermostat was configured a bit differently on mine, but I eventually figured out how to remove it. The video was very helpful, the price for the part was good, and shipment was faster than expected. I will look to PartSelect in the future.

Dryer would Start

  • Customer: Mary from Lewisburg, TN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Took the back off pulled the thermal fuse off placed the new one in and put the back of hte dryer back on

no visual access to the area we trying to work in.

  • Customer: Preston from Ventura, CA
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
To start off I am disabled so I had my 14 year old daughter to help me.I opened the top of the dryer,disconnected the door button and had my daughter help wire the top open and take off the front panel.We took this time to clean out the dryer for it was quite built up with lint.I then gave my daughter my cell phone and told her to stick it in the dryer to take pictures of the area we needed to work on.I then showed her the pictures and explained in detail how everything worked and what she needed to do.I then put the belt around the drum and she proceeded to put the belt on the pulley and tension rod.At this point we are both filty and both have gotten miner injuries.I spun the drum and it and the belt both spun,we thought GREAT we have fixed it,so we put it all back together,plugged it in and nothing.So we take it back apart,but this time I stick my hand in there and find out she didn't have the belt on the pulley,it was wrapped around the tension rod so I fixed that problem.Then I figured out that she hadn't pulled the tension rod over to its proper place so I do that as well.This time I spin the motor fan in front to make sure we have it right.We put it all back together, plug it in and it WORKS,so we throw the jeans in because we have to be at a B DAY party in a couple hours.The dryer buzzer goes off and we both go to check and the clothes are soaking wet.I open the top of the dryer and the brand new belt is broken.So many mixed emotions at this time I cant tell you how disappointed and upset we where.So she took her jeans out and used a hair blow dryer to dry them and I hung the rest all over the house.So I decide not mess with the dryer for a couple days because of my frustrations with it.We have to do laundry everyday,I have three teenagers,so I have clothes drying all over my house every day.Even went to the laundry mat once $40.00 it cost me.A couple days go by and I decide to see what happend. This time I have my 15 year old daughter help me.I completely disconnect the dryer from everything.We put it on top of A table and take it apart.What do I find?the motor pulley is broken and has jagged edges the shredded a piece of the new belt.As I mentioned earlier I am disabled and am on SS so I only get paid once a month and have no extra money so now I have to wait until the end of November to order another belt and the motor pulley.In the mean time there is wet laundry hanging all over my house with fans blowing on it to help dry it faster.So what was supposed to cost approximately $20.00 to fix is now going to total over $100.00.I do thank you for the speedy delivery of the dryer belt and we had A great time at the B DAY party.thanks

Dryer made a loud noise while drying clothes

  • Customer: Hermelinda from Merced, CA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
My husband first had to determine the problem he opened up the back of the dryer (Maytag) model. He determine one of the drum support rollers and bracket needed to be replaced it was really worn out. Once he installed the new parts the dryer no longer made any noise. :)

Dryer would not heat.

  • Customer: Alan from Perysburg, OH
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I thought first it was the heating element. Because I am 50 yrs. old and have fixed dryers before. And that was always the culprit. But, now there are safety features that will prevent heating. With PS videos I was able to diagnose my problem with a continuity test. After checking all. I found it was one part to the thermal cut-off kit (which contains 2 parts/switches). Very easy repair. I ordered my parts on a Thursday just before midnight. My parts were at my door By Saturday afternoon. Awesome website. Awesome service. The help videos PS offers will walk you through any problem. I will use them for every repair in the future. Thank You

drum wheel had flat spot

  • Customer: Michael from Jupiter, FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
Replaced both drum wheels and belt and cleaned lint out of entire unit. Works perfect again. Great fast parts with super on line instruction if you need it.

Thumping noise

  • Customer: Susan from San Mateo, CA
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Followed general instructions from your you-tube video. It was much easier than expected. We didn't know if it was belt or rollers, turned out to be roller, but since we bought both we replaced both.

Belt on dryer replaced

  • Customer: William from Lakeland, FL
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The instructions were easy to follow and the pulley on the replacement part was evenbetter quality than the original. I also followed the recommendation to clean the lint trap. Now the dryer works quieter and better than it ever did. Thanks for your product!

Dryer overheated and thermal fuse blew.

  • Customer: Calvin from Klamath Falls, OR
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
removed back cover and with unit unplugged, removed one wire from each device (thermal fuses and switches) and measured with multimeter. Found thermal fuse open. Removed and looked up and ordered part. Installed fuse and buttoned er up and all good. Hardest part was putting the exhaust hose back on the floor outlet!
All Instructions for the REX3514PQ0
1,126-1,140 of 1,626