Models > RES7745RQ0 > Instructions

RES7745RQ0 Roper Dryer - Instructions

All installation instructions for RES7745RQ0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RES7745RQ0
1,861-1,875 of 1,975
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

No heat in dryer

  • Customer: Maureen from Manalapan NJ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
We started with replacing a thermal fuse, went onto heating element & then to replacing the high limit thermostat. The replacements went very easily with your videos, but unfortunately it did not do the job & there is still no heat.

dryer just quit working during cycle and wouldn't restart

  • Customer: Greg from Winter WI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
just looked up my make and model on parts.select. looked at other peoples problems and went thru the parts list and ordered. videos on installation are helpful.

wasn't producing heart

  • Customer: Kayley from puyallup WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Wrench set
  • 0 of 0 people found this instruction helpful
The thermostate and one of the wires were burnt. Ordered a thermostate and re wired the connector to the wire. All I had to do was replace the thermostate and connect the wires to it. Took me probably 15 to do it all :)

to long drying

  • Customer: wallace from portcharlotte FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
removed back panel. removed wire from old therastat one at a time put on new part re-installed thermastat. Replaced back panel & vent line plugged in better now.

No Heat and Timer Failure

  • Customer: Beth from Columbus GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 0 of 0 people found this instruction helpful
Since I was going to take the back off, I went ahead and replaced the thermal fuse, both thermostats, and the heater coil. I followed Steve's instructions and had all 4 parts installed in 30 minutes! It was so simple, I really have nothing helpful to add except to watch the VIDEOS. I would like to thank PartSelect for making this repair so easy for me. The Instant Repairman feature helped me find parts quickly! The videos, well, a big THANK YOU to Steve for the terrific repair demonstrations!!! Also, reading others reviews was very helpful. I am already telling others about this site, and I will be back (hopefully not too soon).

Dryer would not dry - no heat

  • Customer: DL from Los Alamos NM
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Using the video that is on your website on what and how to replace broken parts, we followed the same procedure. 1. Found the heating element in the back of the dryer after removing the cover panels. 2. Used a volt-ammeter to determine which part(s) was/were not functioning. 3. Used screwdrivers to disconnect/reconnect wires. 4. Closed panels.

No heat

  • Customer: Paul from Westbrook AL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Parts Go Ppppcame in two days, they took fifteen minutes to install.I followed the pdf.instructions from the web site.Cost of parts was less than a service call.

would no longer heat

  • Customer: Terry from Kaufman TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I went online looked up whirlpool and got the phone number and called them told the person on the phone the model number and Ineeded a heating element Igave credit card information had my part in 2days .put that in and discovered Ialso needed athermostat so Icalled whirlpool back and ordered my thermostat and received it in 2 days put the thermostat in put the back on the dryer and I was back in business didn't get behind waiting on my washing ,,not tomention we were in the process of moving thank you you'll worked with me .Iwould buy another whirlpool product easy to work on a and awesome customer service .

dryer ran but no heat

  • Customer: Nels from South Haven MI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
turn off elec./disconnect at recep.- remove vent pipe- remove back of dryer- remove each part and re-install new part- relaced thermal cut-off, thermostat, fuse, and heat element...time about 30 min. also vacuumed dryer and vent pipe-time less than 15 min.- parts arrived day after they were ordered.

Not enough heat

  • Customer: Steve from Yadkinville NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Unplugged Dryer. Removed back panel of the dryer. Disconnected and removed the Thermal Cut Off switch and replaced. Disconnected and removed the High Limit Thermostat and replaced. Reinstalled rear panel of the dryer. Plugged in dryer. Operated dryer and checked for heat. Operation was proper and dryer works great.

No heat

  • Customer: Charles from Monument Beach MA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Click on the problem and find the possible solutions. Click on the part and watch the installation instructions. Unfortunately, mine was a bad thermostat/fuse that can only be purchased with the High Limit Thermostat which I had already purchased. What you might find helpful is that all thermostats and fuses should show continuity at room temperature when using an Ohm meter. Both purchases arrived within 30 hrs. of shipping. I was impressed. I ended up changing all three thermostats but was still way ahead considering a service call is $140 plus parts. I almost scheduled this service until stumbling onto this site thinking the heater was bad but was much cheaper than the local appliance/repair store. Again, the continuity test showed that the heater was fine and everything already mentioned above could be inspected and changed in less than 10 minutes.

No Heat. Timer Wasn't Moving.

  • Customer: tartty from Wilkes Barre PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
First I watched the videos to be sure these parts were easily accessible. After determining the heating element was the problem, I decided to change the other parts only because they were so simple to change. I paid just shy of $100 for parts and fixed the dryer myself, saving who knows how much from a service call. This was by far the easiest appliance repair I've ever done. Thank you PartSelect.

Dryer was taking too long to dry

  • Customer: Robert from Louisville KY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
I removed the 9 screws from the back plate of the dryer. I cleaned all the lint off the wires and the entire back of the unit with a paint brush and vacuum cleaner. Then I removed each part with a nut driver, also removing the wires and replaced each part in less that 1/2 hour! The videos were a huge help. Now my 16 year old dryer works like new. Saved lot of $$$. Thanks Partselct you're the Greatest!

Dryer seemed to overheat and would shut off

  • Customer: Kenneth L from Clearmont WY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Changing the parts was very easy and took little time to replace all of the parts. I did watch the vidoes that where helpful. Troubleshooting the problem took more time than the repairs

no heat during cycle

  • Customer: Patrick from Ulysses KS
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
My grandson and I wiggled the dryer out of it's tight hole, turned it around and squeezed it back in to make room for the repair job. I followed the easy repair video on your site and removed the housing etc, vacuumed the lint collected over the past 6 years, replaced the heater coil and sensor, and had it back within an hour, with most of the time spent on cleaning lint. Thanks for the video!! This kind of DIY can be fun with the right info. Great bonding-time for generation gap, too. Dryer works like new.
All Instructions for the RES7745RQ0
1,861-1,875 of 1,975