Models > RES7745RQ0 > Instructions

RES7745RQ0 Roper Dryer - Instructions

All installation instructions for RES7745RQ0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RES7745RQ0
1,741-1,755 of 1,975
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

blower wheel cracked and broke

  • Customer: Kellie from Norton MA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
i took the back apart to find the problem, then i went online to findout how tomremove the blower wheel, just googled it. Easy!Took itnall apart, just had a bit of trouble getting the wheel off, was on there very very tight. Ordered it through you, easy, and very very quick, received it in a day. I got an email explaining the reassembly process. Easy. Just follow it to a t and you will be fine. As a woman, this was an easy fix.

Tall Drum Baffle came loose

  • Customer: Helena from Oregon OH
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I am a female, not a handy man. But by following the repair man on the video, it was easy. I also went ahead and installed the maintance kit. The maintance kit was recommended when I ordered the parts. I followed by maintaining the washer.

Washer overflowed

  • Customer: Beth from Valley Springs CA
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Once I watched a YouTube video showing me how to do the job I ordered the part from you. Am so impressed with your fast shipping and best prices via the Internet. Thank you SO much! The water level switch was easy to install, it ws getting the cover on the washer back on that was hard for me since I am 68 yrs old and have a bad knee. Its why it took me two hours to do what most people could do in 20 minutes.

ice tray was broken

  • Customer: mike from fitchburg MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
This was by far so easy the instruction Partselect gave me where right on step by step. a repair man was going to charge 75$ just to come out 9$ from partselect. Thank you very much Mike chaplin

The leveling foot on my dryer broke.

  • Customer: Diana from Clifton NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
We only had to tilt the dryer enough to be able to screw the leveling leg in place.The only hard part was holding the dryer steady to screw in the leveling foot.

Took to long to dry clothes.

  • Customer: Larry from Sierra Vista AZ
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Replace the heating element and themostats. Saved me $$$ from me buying a new dryer. Thank U for the videos also. Great help.

Dryer would not start

  • Customer: Marianne from Solon OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
My dryer is a KitchenAid KEYE660W (electric). I tried to start the dryer but it would not run. I did notice that if I held the start button down, I could feel light vibrations through the button. Searched through Yahoo and this site and determined that this is often a bad Thermal Fuse. Used the diagrams on this site to locate where it should be, removed the back of the dryer with a screwdriver, removed the two wires clipped to the Thermal Fuse and unscrewed the Thermal Fuse. I had a friend test the fuse with a Multimeter. It was bad so I ordered another one on this site and it arrived in two days. Screwed the Thermal Fuse back in and clipped the two wires back on. Started the dryer and it worked!!! Replaced the back of the dryer. This repair took 15 minutes MAX and taught me a little bit about Mulitmeters.

the lint chute assembly had corroded & would not accept the lint screen.

  • Customer: Richard from Paramount CA
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
I pulled thee dryer out from the wall, shut off the gas & disconnected the gas line & the air vent, I then removed the fasteners from the upper end of the lint chute assembly (accessible from the top of the machine). I then tipped the machine over on to its front side making the back fully accessible. After removing the back cover, I removed the remaining fasteners holding the lint chute assembly in place & removed the part. I then removed the assembly only to find that the seals were not included in the package even though I had specifically asked about the seal when I called in & place my order. The response to my question was " seals are included that is why it is called an assembly." The end result was that I had to use alternate material & fabricate my own seals in order to complete the installation. As a result a repair which should have taken no more that 30 minutes, took over two hours.

Dryer wouldn't start... Just a hum when you press the start button.

  • Customer: James from Festus MO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Well it took me longer to get the dryer apart and than it did to get it back together... Well I opened it up it was obvious I had burned up the motor you couldn't even see it for all the lint that was built up around it... And the hardest part was removing the fan from the motor shaft, I didn't realize it was plastic and sort of mangled it getting it off so I went ahead and replaced it as well. The hardest part of the whole repair was removing and replacing the clips that hold the motor in place and there didn't seem to be any trick to it, I used a pair of channel locks and a little muscle to get them off and back on everything else was a breeze! I recommend checking the exhaust pipe at least once a year to make sure air is flowing freely to prevent the lint build up inside and even more often if you have a long run. This should prevent having this problem again...

i had difficult time getting wheel off.

  • Customer: dwight from monticello AR
  • Difficulty: Very Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
found out that pushing in on wheel and turning counter clock wise, wheel screws off rather easy.

Broken belt and bent idler pulley

  • Customer: Mollie from Walterboro SC
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
First unplug the unit. Take the lint filter out and remove the two Phillips-head screws at the edge of the opening. Then using the putty knife to unlatch the top panel of the dryer, insert it into the seam on the front about 3" from each side. When you feel the knife up-against the latch, apply a little inward pressure with the knife and pull up on the top panel. When you release both sides the panel, it will lift up and back against the wall(secure it so it doesn't fall forward while you are doing this repair). Looking down on the right-front corner you will find a connection for the door switch, Dis-connect it. Just below that connection, on the inside, is a 5/16" screw that holds the front panel on, take that one and another one just like it on the left side, out and the front will fall forward about an inch and then you will lift up on the panel while holding drum in place. Inspect the clips that hold the bottom of the panel on and be aware how the panel attaches to them. Try to keep the drum in place and set the front panel off to the side so you can easily grab it to put it back on. Looking under the drum remove the belt and idler pulley. The pulley is usually not in the position it should be in, it likes to fall over when it has no belt pressure on it. Hopefully you had already unpackaged the new belt and straightened it out. Loop the belt over the drum, rib side to the drum, and move it to where the old belt had been riding on the drum. Back under the drum, you should hold it in place with your shoulder, with idler pulley in hand-- install the idler pulley. There's probable a clean spot where the old one was and the humpback should point to the right side of the dryer. With right hand steadying the idler pulley, the left hand should pinch the belt together and feed it under the wheel and pull it out and hook it on the motor pulley. It may seem to be a tight fit but once its on you should be able grab the outside edge of the drum and slowly turn it without hearing any scraping noises. Double check that the belt isn't twisted. Before putting the front panel back on or if you had to take the drum out, make sure the felt seal on the back edge of the drum is not folded inward. the wheels that the drum roll on must be in the groove. Carefully reach to the back to check that they are in the groove of the drum. If everything seems to be in place, hold the drum with one hand and grab the front panel with other. Place the bottom of the panel against the unit and lift up about an inch and place the square holes at the bottom of the panel on the clips on the unit, it may take a couple of tries, then lean the panel forward making sure the drum goes around the felt seal on the panel. Once the panel is against the unit , install the two 5/16 screws securing the front panel to the unit. Turn the drum by hand to make sure drum was installed properly. Reconnect door switch. Lower top panel and push down to secure it. Install the two Phillips head screws at the edge of where the lint screen goes, install lent screen and plug the unit back into the wall socket.

Door switch hadn't been working for a while and when the belt broke decided to make it right.

  • Customer: Martin from Saylorsburg PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed front and replaced belt,idler pulley and door switch. Was an easy repair.

Belt & clip where both broken

  • Customer: Amy from Seagrove NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
My 11 year old son and I ordered the parts we needed. Saw the GREAT easy installation video, It even was attached to my confirmation. After the parts got here him and I easily took off the old belt and clip, installed the new ones (after watching the viedo again) and we where done. You would have thought we fixed the space shuttle or something because we both smiled all day. My son also told every one that he and his mom fixed the dryer all by ourselves. Costed me only $40 dollars for the parts. I couldn't have even called a repair man out there for that. Thanks soo much.

Lould nosie from Drum Whells

  • Customer: FRANCIS from PHILADELPHIA PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I watch and followed the three viedos that PartSelect emailed me and had a very easy repair job.

drum not turning

  • Customer: Tony from Greenville IL
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Watched a video on utube and realized how easy this looked, took my dryer apart to see the belt broken in half and the idler pulley in pieces. Found Partselect on the internet and ordered my parts. Partselect was awsome, website was easy to navigate, ordered my parts and they were at my house the very next day and were the correct parts. Cleaned all the lint and dust out of the inside of my machine, installed new parts and put it back together. Works great and is still running strong. A service call, plus parts (with thier mark up) could have easily been $150.00 - $200.00 dollars. this repair was complete in about an hour and only cost me $37.50
All Instructions for the RES7745RQ0
1,741-1,755 of 1,975