RES7745PQ0 Roper Dryer - Instructions

First I purchased the heating element, still no heat. Then I purchased the thermal fuse,still no heat. I have been pleased with the prompt shipment of the parts and the parts arrived safe. Thank you for service and time, not sure what to do now.I will recommend PartSelect to friends.

Unplug unit / removed back cover / went down , locating both parts to be replaced / simple one screw removal from each part / thermal fuse , one wire @ a time , reinstalled . / Cycling thermostat , 4 wires. Did one wire @ a time , reinstalled. / Putted back cover back on , plugged dryier back up, turned it on to run. To check for heat / yes, ran good as new. Later that day some more running , with damp clothes in it. Did it's job , dry.

I followed the repair method as described in the how to video it was as easy as that. Dryer is now working perfectly

Took the back off of the dryer, looked on "parts select" found what I thought might be the problem. Got the parts the next day. Put on new thermal fuse, then put on cycling thermostat. Wasn't sure which it needed, so put both on. Put the back of the dryer on hooked the gas up, hooked up to electric, & turned the dryer on. Back in business, everything works, dryer works as if nothing was wrong. Thanks to "parts select" saved me a repair bill.

I watched your video on how to replace the fuse.Wow it was a lot easier than I thought.I would highly reccomend anyone to watch the video before even trying to do any repairs.The dryer is working like a new one.By doing it myself saved me a lot of money.Thank you

Removed two screws at the top, removed two screws for the front panel, removed the broken belt, installed the new belt, followed the directions that were in the new belt package, and replaced all the panels and tested. It worked.

What a pain in the butt to route the belt thru the tensioner! There's room for only one hand in there. The guys who do this for a living must have some secret. My solution was to drill a 3/16 hole thru the side, make a j-hook from 8-32 threaded rod, use that and a wing nut to pre-load the tensioner, route the belt, then slowly back off the wing nut until the belt was tight. It works. . . .

Replaced the part. It just slid right in to the appropriate space on the dryer.

first I unplugged the dryer. Then I removed the back of the dryer with a 1/4" nut driver. with the back off using the same 1/4" nut driver I removed the one screw that holds the cycling t-stat slowly remove the t-stat and take one wire off at a time and plug it onto the new t-stat once all wires are replaced. place the t-stat back in and secure with the screw. Then put the back of the dryer back on. put the dryer vent hose back on. plug in and away you go. repair done. If that doesn't fix it. Then the next step is probably to check the gas valve coils. That is a little more difficult repair but not to hard.

Remove back pannel heating element easy to replace. Partselect has the best service ever...

Watched several videos online and was suggested that the thermal fuse was bad, so i replaced it but no fix. So i checked the previews Q&A from other costumers and watched the videos on how to replace different parts. I first looked thru the peep hole on the bottom left part of the dryer and saw the igniter glow for about 10 sec every minute but no flame would start. So i replaced the igniter, the flame sensor, and the coils all at once. I know thats not the proper way to troubleshoot something but i was gonna take the drum out and everything so mind as well replace them all. Dryer works like new and dont have to listen to the wife complaint anymore!!!

in error i replaced push to start swirch. then went back on line and determined it was thermal fuse. easy to confirm, and easy ro repair. dryer now like new. push to start switch easy, 2 screws removes control panel. reach in, twist switch one quater turn, then move wires to new switch and reinstall. no need to pull dryer from location. thermal fuse requires removing dryer back. easy repair.

Pop off the top , Then one screw holds each side . slide belt around drum and then preload tensioner as per instructions . Simple!

The video is right on. You can't go wrong, and I don't consider myself a handyman at all.

I replaced both the Thermal fuse and Cycling Thermostat, both of which cost less than fourty dollars. just removed the back panel, and replaced the parts in less tham a minute. Replaced the back panel. Job done.