Quick Question!

Have you ever purchased from PartSelect.com before?

Models > RES7646KQ0

RES7646KQ0 Roper Dryer - Overview

Get Parts and Repair Help for RES7646KQ0

If you know the dryer repair part you need, you can browse the list of all parts on the RES7646KQ0, or you can search by name or part description. You can also find your part by where it is located on the RES7646KQ0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for RES7646KQ0 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the RES7646KQ0

[Viewing 3 of 3]
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$8.98

Thermal Fuse

This thermal fuse is designed for use in dryers. It is a safety mechanism that stops the flow of electricity to the heating element when a dryer overheats. When this fuse is faulty...

$14.56

Multi Rib Belt - 92-1/4"

This multi rib belt is an important part in your dryer, it is what helps rotate the drum. The belt attaches to the drum, idler pulley, and motor pulley. As the armature of the motor rotates, the belt begins to move and turns the drum. If you notice the drum of your dryer is not spinning during the dry cycle, but you hear the motor running, your belt may have snapped and it will need to be replaced. This belt features four ribs and three grooves, however it replaces a wide variety of belts including wider styles that had five ribs and four grooves. When installing this part make sure the grooves are facing down, against the drum. This replacement part is 92 1/4 inches in length, and 1/4 inch wide. Before you begin any repair work, make sure your dryer has been unplugged.

$103.48

Heating Element - 240V 5400W

The heating element is strung with a coiled wire that is made out of a nickel and chrome alloy. The function of the coiled wire on the heating element is to receive and resist a co...

$14.81

Door Switch - 3 Wire

A door switch is a simple on/off switch mechanism that prohibits the dryer from operating when the door is open. This part may need to be replaced if you find that the dryer is not starting, will not shut off or the door will not close properly. All you will need is a putty knife and a Phillips screwdriver. Pry open the top of the dryer, remove the two screws underneath the lint collector without removing the entire thing, unplug the switch, remove the screws that hold the switch place, take out the old switch and install the new one by screwing it back into place.

$14.96

Thermostat, Internal-Bias

A cycling thermostat is in tune with the temperature of your dryer and regulates it in order to maintain a certain temperature. This thermostat reaches a temperature of 155 degrees...

$3.56

Door Catch Kit

This is a door catch kit, and it is designed for use with your dryer. On your appliance you will find both a strike and a catch, these two parts work together to keep your dryer door closed. This kit includes two strikes, three catches, and a set of instructions. Each of the door catches included have a different tension. Make sure you use the one that matches the existing catch on your appliance. All three of these are color-coded, and have a number on the back. The instruction sheet will tell you which catch you need to use for your specific model type.

$36.87

Thermal Cut-Off Kit

The thermal cut off turns off the heating component when the dryer overheats, ensuring there is a consistent level of heat at all times. This dryer thermal cut-off kit includes one...

$12.47

Rear Drum Support Roller Kit

The drum support roller kit allows the dryer to tumble properly by supporting the drum cylinder. The kit includes two drum rollers, four tri-rings and one palnut (or retaining washer). The kit does not include a belt or idler pulley and rollers are not sold individually. The drum support roller kit may need to be replaced if the dryer is noisy or will not tumble. The tools needed to complete this repair are a putty knife, Phillips screw driver, and a 5/16 nut driver. It is recommended to look at the rear felt before reassembling the dryer to ensure there are no gaps or damage. This is an OEM part sourced directly from the manufacturer.

$10.69

Thermostat, High Limit 221 F (

This hi-limit thermostat with Terminal Extension Arm acts as as safety mechanism that keeps the dryer from overheating. Once the dryer temperature reaches 221 degrees Farenheit, th...

$10.04

Idler Pulley Assembly

This part provides the tension required for a multi-ribbed belt. It also serves to help the belt to rotate the drum and attaches to the idler pulley wheel. If your dryer will not start or tumble, takes too long to dry, or is noisy during operation, you may need to replace the idler pulley assembly. Make sure to disconnect power before installing this part, and work gloves are recommended to protect your hands. While the dryer is disassembled for this repair, consider replacing the drive belt as well. You will need a putty knife, a Phillips screwdriver and a 5/16 nut driver for this repair.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dryer was working, but no heat.

  • Customer: ANTHONY from CHESHIRE, CT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 2114 of 2379 people found this instruction helpful
First I unplugged the dryer, then removed the back panel, this exposed most all of the wiring and I could see the heater coils.
Not knowing what the problem was I started looking at the coils and could not see any broken parts.
So then checked the thermal fuse for continuity I removed the two wires from it with a small pair of needle nose pliers, ... read more

Dryer motor runs, but no heat

  • Customer: Gadi from Irvine, CA
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 1982 of 2134 people found this instruction helpful
To reach the heating element you only need to open the back cover of the dryer (about 8 nut-head screws). Remember to disconnect the power.

To remove the heating element there are two small nut-head screws. Remove the two electric wires. Then you can pull the heating element away.

You can check the heating element with an ohm-meter or v... read more

door switch was bad

  • Customer: pat from lisbon,, OH
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set
  • 916 of 939 people found this instruction helpful
i was able to go on line with your company , find my dryer, order the part and had it the next day. fast , great , service read more