REP3622BL0 Roper Dryer - Instructions

layed the dryer door side down, took 6 nuts off back metal panel, then took the bolt off at bottom and reached in and pulled drum support rod loose, removed old roller, installed new roller, reached in set drum support rod back into hole where the threads were showing on the outside where the nut was then put back on and tightened back up, put a pair of vicegrips underneath on rod to hold in place while tightening up nut,placed cover panel back on with screws and now it works like a new one, runs very quiet. Cost was 25 dollars for part nothing to do it ourselves. We priced new dryers that size they're well over 400 dollars. Easy REpair!!

For 2 years, I propped a broom stick against my dryer door to keep it shut while it was running. Last Sunday night, I decided that it was about time to fix it. I found the PartSelect site, which was extremely easy to navigate, and ordered a replacement kit. It arrived in 2 days via Fed Ex and actually contained extras of each of the 2 components, in slightly different sizes. It took me about 10 minutes of eyeballing the parts to figure out how to place them and about 30 seconds to install the new latch parts. They fit perfectly. Great site, great service, I would highly recommend this site.

ordered wrong limit switch had to reorder right switch and decided to replace the heater element as well. works fine now

Read the Use & Care Guide! I spent several hours trying to repair a dryer that was not broken because I was unaware of the "lint signal". While replacing a burnt out heater element I apparently disturbed the flapper on the lint signal box and it stuck in the open position. My wife who does the laundry has always kept the lint filter clean so we had never heard the lint signal and I assumed that the high pitched sound I was hearing must have been from a faulty gasket, belt, roller, pully, or motor. Boy is my face red!

Watched the how to video on the parts select site. The job to replace the motor was easy although I had some issues with the blower fan wheel as it is made of plastic and was frozen to the motor, yes I turned it the correct way for the left hand threads. I ended up distroying the blower fan wheel and had to buy a new one. I had to remove the rear plate to get at the fan component, but thta was easy to do also. This site should add a "Sometimes bought together" comment for the motor replacement. After all was done I read some of the other comments and found some others had the same problem with the fan wheel. Once I had all the parts the dryer went back together fairly quickly. The job was easy to do and I would believe almost anyone could do it.

replace the water valve

just the way the video showd me

It is a washer/dryer combo. First I unplugged the unit. I had to remove the top and front of the dryer, remove the belt and remove the drum. I then removed the side panel that the motor was on. That was a little tricky getting at a couple of the screws. I then took the flywheel off which was somewhat difficult. It screws off in the opposite direction and was hard to get loose. I unplugged the motor, no wires to connect. There is a clip on the front and back of the motor holding it in place. Take them off and the motor comes right out. Replace the new motor and screw the flywheel back on. Install the clips, plug the motor in and put everything back as you took it apart.

I am one Happy Gal.....Looked to fix,thought about just buying a new dryer..In the end talked to the local repair guy...said I could do it myself. (why pay him)..I live in small town.Ordered your part,watched the video and did it...Saved myself over $500, plus the $125 for delivery.for that new dryer..(Small town in the forest!)Very easy to install....Hope to use this dryer for many months perhaps years..It is 30 years old! Works like a champ! Thank You!

Stuck it in, done. The really good thing was your website - the BEST I've ever used to order anything on the web, bar none. SO clear, SO organized, SO logical, SO easy to use. I just wish other companies using the internet to sell things would learn from you guys. Kudos to you and your webmaster, really outstanding.

Took the back off the dryer. Disconnected the old thermostat and installed the new thermostat. Connected the back of dryer. Put in a load of clothes to dry and the clothes were dry on the first try. Works like a new dryer. Saved a lot of money not having to buy a new dryer when all I had to do was replace some old parts.

removed front panel and drum and replaced drum support rollers

Reviewed video on how to disassemble appliance by removing drum. Removed both rollers, replaced both rollers, installed drum with new belt, test ran it w/o gas attached, so quiet a baby can sleep beside it.

Drum support roller bearrings went out. Had to replace drum support rollers! It's like a new dryer now!!

Used repair video as guideline, I did not have their lab conditions to work in and by no means a clean machine. Also I had a two part front panel vs. single as in video, so disassembly and reassembly were OJT."on job training". Video was however very usefull in locating problem, getting correct part and accomplishing the repair. Saved $$ and machine is now working properly again. Am saving this web-site to my favorites list.