REL4634BL0 Roper Dryer - Instructions

Looked up on-line for tips, found computer animated video. It was easy as it looked, took longer to take dryer apart (not long). Other note on problem; neighbor who works on washer/dryers said that the motor was probably going. replaced belt anyway because I already purchased it before we spoken. Throwing caution to the wind!!

I watched the informative video you sent via e-mail with order conformation. Installation was flawless. Thanks and will be using your site again for any other small appliance repairs that may need my attention.

This repair took me longer because I was just giving it a try - I have no experience, although I tend to be "handy." I'm sure anyone with experience would rate this as "easy" and have taken only a short time. I had to watch the video several times to understand what to do - and the comments were helpful too. My washer is an OLD maytag, so I removed the front of the dash and pulled it forward to access the electronics. My switch had only 2 prongs, so I hooked up to the "lid closed" option on the new switch. It works perfectly now. Very pleased I gave it a try.

I watched the online video three times. This was extremely useful. I just did what it showed. I doubt I could have fixed it without the video. This has got to be the best feature of the internet. I didn't have the exact model number, but the belt fit. I was surprised at how close the tensioning wheel was to the motor. Perhaps the belt will stretch with age and use.

We noticed the drum wasn't spinning, but the heat was turning on. About 3 years ago the heat was broken and it turned out that there was a little thermal fuse in there that needed swapped out, that was easy too fix too. Anyway, I looked up on youtube how to change out dryer belts on maytag units and it looked pretty straight forward. The model they showed was easier to access than my model, but I was able to still figure it out. Just pop off the top panel (they used a putty knife at the two clip points on the front, but I just yanked it up with a little force and it popped right up). Then unscrew the two little screws holding the front panel on, then pull off the front panel completely. This exposes the drum. The example on youtube showed easy front access to the belt assembly, but in my model, there was a stand for the drum as well as the drum motor in the way. So I just pulled the whole drum out the front most of the way, then I went behind the drum where I had exposed the pully/motor shaft assembly and then fed in the new belt into belt tension assembly that connects to the motor. While keeping it taught so the ribs of the belt would stay on the motor head (I had my wife hold it taught) I pushed the drum back toward the hanging belt and then worked the edges of the belt around the drum until it once again was completely around the drum. Then I slowly pushed the drum all the way back into place while continually working the belt back into place as I went. I then manually rolled the drum around a few times to ensure it was rolling correctly and that the belt was indeed in the right place. After a few good spins without it changing position, I reassembled the unit. It was very painless and took about 15-20 minutes in all. Works just fine again.

I replaced belt by myself. Took dryer apart,laid dryer on its back, put belt and pulley on. Rotated drum to make sure seal was in place. Cleaned out machine while I had it apart.

Followed the instructions and really quite easy to fix. I didn't know why dryer wouldn't turn on but went with the odds that the thermal fuse was the problem-- and it was. Once I got the part it was back together and running in less than 30 minutes!

I am a licensed electrician I found the bad part and I ordered it and when it came in I replaced it.

Removed two small screws on door edge, pop out broken part, insert new part, replace screws. Took 2 minutes 18 seconds. Nice to have various door catches in the Kit. This was a repair on a 1979 Whirlpool Dryer. Great price & service!!

Removed plug. Removed lint pipe. Unscrewed lint trap under top opening. Popped the top up. Used nutdriver to remove top 2 screws of front panel. Lifted front panel and set aside. Lifted drum out. Replaced wheels and idler assembly. Parts were well engineered and fit perfectly. Vacuumed entire interior. Placed belt around basket. Replaced basket. Slipped belt thru idler pully and onto motor pulley. Tested basket one full turn to make sure the seal was in place all the way around the back. Slipped front onto two bottom brackets. Replaced screws in front with nutdriver. Dropped top back in place. Pushed down into holders. Screwed lint trap back in place. Replaced plug and tested. Replaced lint pipe. Done!

My husband and I followed the video step by step and it worked like a charm.

My Whirlpool washer/dryer combo is 15 years old and has given trouble-free service until this belt snapped. I went to the PartSelect website for the replacement part and found the instructional video. As a DIY neophyte I know my limits but this looked like something I could tackle and save a few bucks on. The part arrived pronto and installation went smooth as butta! I couldn't be happier and even the wife is impressed. Knowing what a service call would have cost makes the whole shebang even sweeter. Thank you PartSelect!

I removed 2 screws to the lint trap, popped top of dryer with a flat screwdriver but did not remove it I just raised it and leaned it against the wall. I removed 2 screws from the top of the inside front panel,then I hooked the new cables to the springs that are on either side of the front panels at the top. I then pulled the panel forward just enough to fit my hand and thread the cables through the holes that are on the front panel that lead to the door, I had already popped out 2 plastic caps that go inside the door on both sides.I then treaded the cables inside each hole and snapped the caps back on. Iris

Pulled out old filter. Recycled. Slid in new filter. Closed plastic cover. Voila! Done! No real "repair" involved. More of a replacement.

after the removal of the front i removed the drum and inspect all idler wheels for ware replace if needed. if not clean and lube. idlers must be in good condition...bad idler wheels can cause the belt to brake