REL4622BL1 Roper Dryer - Instructions

It was not hard at all. I got the parts the next day.

I ordered kit to your recomendation, took machine appart as per your video (Very helpful), put machine back together only to find that that was not the problem.No other recomendation as to what else I should.

Verified that the heater element was working; drum and contents were getting hot. Could hear the thermostat clicking on/off as the element started to glow. Drum stayed very steamy the entire time; consistent with no airflow. Fan motor was running, dryer vent/line were clear. Verified cold (not hot) air from the external vent. Seals had degraded to the point that the fan was not drawing air from the drum, but from inside the dryer cabinet at the lower seal (by the fan blades); hot air was escaping from the upper seal and was causing the dryer cabinet to get unusually hot. Installed these 2 seals, and the dryer is working perfectly now.

TURN OFF POWER TO DRYER............................. Pay attention to where everything is as you take it apart, so it can be put back the same way. Take out the two screws by the lint screen. Use flat tip screwdriver between space in front of top to help lift top. Use rag on tip of screwdriver so as not to scratch it. Take out two screws inside the front panel at the top. One on each side. Unhook the switch wiring. Lift up the front panel to take off. The tub will be loose, so it can be taken out to inspect other components. Some call the tub a drum. Be sure to see how the belt tensioner is attached, so it can be put back on the same way, if it comes loose. It is under the tub. Take out old belt. Put new belt around tub. Make sure the tub sets on the two rollers in the back of dryer. While holding tub, put the belt around the grooved pulley on the motor. Grooves are face down against the tub. Feed belt through the tensioner. Put the bottom of front in on the tabs. Be sure belt is still in place around pulley and tensioner etc. Hold tub through front door and close front. Put the two screws back in on each side. Close top and put the two screws in at the lint screen. Done. Turn power back on. Turn on dryer to see if it operates properly. If not, check out your repair to see if everything is connected properly.

unplug take off vent hose and back panel unscrew one bolt holding the fuse disconnect 2 wires. Connect the 2 wires to the new fuse hold in place with the bolt put back on the back panel and vent hose plug in and your done

Used PartSelect instructions for routing belt & a customer's valuable guidance.

I changed the thermal fuse following instructions from the video on the site . Very easy repair, anyone can do it.

I removed screws for the lint screen - TOP. Pry up top with screw driver. Disconnected inside top front 2 screws, removed door control wires, white and blue. Lift off front of dryer. Tip dryer back about 40 degrees against wall. Remove warn belt (not broken). Relocate idler bracket on the cabinet base, follow diagram which comes with the belt package. Be very careful that the belt is NOT on the side of the idler roller. I had to do this install a second time, because I had it wrong the first time. Even though I've done this repair 5 or 6 times, there's always a first time GOOF. Not really a hard job.

Threw away the printed instructions and followed the Part Select video ,featuring Steve...

Well my husband did the install and he said it was very easy??

Removed the current (broken) block by unscrewing the screws at each end. I decided to re-use the wires / connectors in the dryer, though. The connector on the dryer is held in the block by a bent tab, about half way along the connectors length. I pushed this with a screwdriver and pulled the connectors off the current block. Sometimes I had to re-bend the tab prior to putting on the new block. Then I slid the connectors into the new block. To do this, first you put the captive nut into the slot, and then you put the metal end of the connector below the block, so the wire is around half-way down the block. Then slide the metal in, trying not to pull on the wire. Lastly I reattached the block to the machine using the two screws. Didn't need the terminal block screw kit, as these parts were in the block-term kit.

always unplug from outlet first, unscrewed the back off and pull off the wire from cycling thermostat ,take the two screw out that holding it in place and replace the new one .Very simple and easy. Thank you for the easy step by step video to complete this repair. James

Instructions are available from other web sites. A few tips from me. Tape the dryer doors shut. When you remove the springs it falls open. Remember to just loosen the hex screws at the bottom of the front panel, it has slots and just lifts off of them. To easily remove the clips holding the motor bearings use a dull chisel or small pry bar on the outside half loop and tap the end with a hammer while lightly forcing it out.

Watched a you tube video on replacing a dryer belt for a whirlpool dryer. Perfect instructions. Dryer is working great.Thank you

I'm a 66 year old lady with no repair experience at all!! I found the part I needed on Parts Select, which I ordered and received in less than 4 days. I watched the video that you've posted on your website which shows in great detail how to do this repair. It looked like a simple fix and it was!! I highly reccomend Parts Select!! Took my granddaughter(held flashlight) and myself less than 30 minutes to do the repair!!!