Models > RED4640YQ1

RED4640YQ1 Roper Dryer - Overview

Get Parts and Repair Help for RED4640YQ1

If you know the dryer repair part you need, you can browse the list of all parts on the RED4640YQ1, or you can search by name or part description. You can also find your part by where it is located on the RED4640YQ1 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for RED4640YQ1 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$11.11

Thermal Fuse

This part is a one-time use thermal fuse which attaches to the blower wheel housing of your clothes dryer. It cannot be re-set and must be replaced when continuity between the pins...

Order within the next 6 hrs and your part ships today!
$11.97

Multi Rib Belt - 92-1/4"

This dryer drum belt has four ridges, three grooves and is 1/4" wide.

Order within the next 6 hrs and your part ships today!
$51.06

Heating Element - 240V 5400W

This element is strung with a coiled wire made of a nickel and a chrome alloy. This wire receives, but resists, a controlled electric current and as a result, the wire heats up. Th...

Order within the next 6 hrs and your part ships today!
$14.09

Cycling Thermostat

Cycling thermostats continually cycle the heating element off and on to maintain a constant inner temperature. This particular cycling thermostat has a limit of 155 degrees Fahrenheit and a differential of 25 degrees. Meaning that with this thermostat, the heating element will cut out at 155 degrees and cycle back on once the internal temperature drops by 25 degrees.

Order within the next 6 hrs and your part ships today!
$28.84

Thermal Cut-Off Kit

This clothes dryer thermal cut-off kit includes one high limit thermostat with a limit of 250 degrees Fahrenheit, and one thermal cut-off fuse (309 degrees). This kit also includes...

Order within the next 6 hrs and your part ships today!
$14.80

Door Switch - 3 Wire

A door switch is a simple on/off mechanism that prohibits the dryer from operating when the door is open.

Order within the next 6 hrs and your part ships today!
$33.43

Maintenance Kit

NOTE: This kit is for 29" wide dryers built 1965 or later. Please verify model # before ordering as may not work for all models. This kit comes with one multi-rib belt, two drum ...

Order within the next 6 hrs and your part ships today!
$10.45

High Limit Thermostat

This hi-limit thermostat with Terminal Extension Arm acts as as safety mechanism that keeps the dryer from overheating. Once the dryer temperature reaches 221 degrees Farenheit, this piece will shut down power to the heating element until it drops by 80 degrees Farenheit.

Order within the next 6 hrs and your part ships today!
$15.35

Drum Support Rollers

These two drum support rollers are no longer available for individual sale. Available in a package of two and it is recommended that you replace both rollers at once. These two rol...

Order within the next 6 hrs and your part ships today!
$4.54

Heating Element Connection Wire Kit

This kit is used for electric clothes dryers, and it comes with a yellow wire nut.

Order within the next 6 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dryer motor runs, but no heat

  • Customer: Gadi from Irvine CA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 1443 of 1574 people found this instruction helpful
To reach the heating element you only need to open the back cover of the dryer (about 8 nut-head screws). Remember to disconnect the power.

To remove the heating element there are two small nut-head screws. Remove the two electric wires. Then you can pull the heating element away.

You can check the heating element with an ohm-meter or v... read more

Dryer was working, but no heat.

  • Customer: ANTHONY from CHESHIRE CT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 1375 of 1572 people found this instruction helpful
First I unplugged the dryer, then removed the back panel, this exposed most all of the wiring and I could see the heater coils.
Not knowing what the problem was I started looking at the coils and could not see any broken parts.
So then checked the thermal fuse for continuity I removed the two wires from it with a small pair of needle nose pliers, ... read more

door switch was bad

  • Customer: pat from lisbon, OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set
  • 603 of 608 people found this instruction helpful
i was able to go on line with your company , find my dryer, order the part and had it the next day. fast , great , service read more