Models > RED4440SQ0 > Instructions

RED4440SQ0 Roper Dryer - Instructions

All installation instructions for RED4440SQ0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RED4440SQ0
1,366-1,380 of 1,927
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

belt broke

  • Customer: Terry from Holday, FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I have never done this before, so I watched the video and also watched a youtube video for this model to repair belt. Used a gallon paint can to hold up the drum, while I secured the belt. whoooo hooo I did it all by myself...59 yr old Female Do it yourself enthusiast! Thanks for all the information.

broken drum belt

  • Customer: Richard from Westmorland, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Shut off power. Opened the top, removed 2 screws one on each side of front door. Opened clip and removed switch and unplugged wire. Removed front door by lifting it up off bottom clips. Removed the drum and checked the drum support wheels, idler and motor pulley. Shop vacuumed everything to get all the lint, dirt and spider webs out. I was lucky, my idler has a spring, so I cut a small piece of wood and put it between the exhaust pipe and the idler to keep it out of the way. I replaced the drum, slipped the belt over the drum and centered it over the pulley (old belt mark on the drum). I reached under the right side and put the belt around the motor pulley and carefully removed the wood holding the idler, turned the drum by hand to check it. Set the front door back in place, plugged the wire back in, put the switch back in the clip, put the 2 screws back in, turned the drum by hand again. OK! Turned power back on and started the dryer. Total new belt installation time was under 10 minutes.

dryer would not stop when door was open

  • Customer: charles from tyler, TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
found that the lever on the switch was broken,i found one on the part select website and ordered it. the picture was very helpful in confirming the right switch was being ordered.thank you

Dryer Would Not Start

  • Customer: SALVATORE from COMMACK, NY
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Disconnected power to the dryer, opened the top of the dryer by sliding a thin scraper underneath the top on the front of the dryer and the pushed the top of the dryer up. I then disconnected the wire on the switch to isolate the switch from the wire in the dryer. I then removed the switch by unscrewing the two screws on the switch and then replaced it with the new switch. I then reconnected the wire to the wire in the dryer.

Dryer would not shut off

  • Customer: Les from Slinger, WI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I removed the top of the dryer and removed the faulty switch form it's mating connector. The simply removed two Phillips Head round headed screws with a screw driver and replaced the part all within 15 minutes. However, I also heard that it wasn't drying properly so after making sure my dryer vent was free of any lint build up, I removed the back of the dryer. Once removed, I completely cleand any dust from inside the dryer, then checked all of the visable wire connections and then went to PartSelect's fantastic web-site. Her they catagorize the top 7 reasons that could cause the problem (in my case) not drying and thenproceed to give you an idea of the most likely cause by publishing the failure rat in per centage values in decending order, they also provide schematics and the on top of all of that...they provide mini-videos not only showing you wher the parts are located but the step by step instructions on how to remove them and replace them. After all of this, I took my ohm meter and actually removed all of the 7 parts suggested, cleaned them up, ran a continuity check on each part and found them all in working order. Replaced the parts and checked the heat and it was back to normal!! There must have be a lose connection causing the problem. But, I can guarantee that the next time I have an appliance problem...I'll again be calling on PartSelect.com. They are awesom and they will be highly recommended to anyone I know that is experiencing problems. I have not ever seen a web-site that was so complete in excellent service. And there prices and shipping time speaks for itself. They are great!!

Off switch on door was broken.

  • Customer: David from Reisterstown, MD
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the video and did exactly what I was shown. Piece of cake. Thanks!

Would Not Stop When Door Was Open Then Would Not Start

  • Customer: ruth from crosby, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Unscrewed bolts off back (2). Took dryer vent out unscrewed the bolts (2) pushed top back and lifted up. Open door unscrewed the bolts (2) to the safety switch pulled the connection (wires) apart and replaced with new safety switch.

Dryer would not run.

  • Customer: James from Logansport, IN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I unplugged the dryer from the wall outlet and remove the two screws from the lint filter area, followed the instructions that were in the repair video and put the appliance back together and re=attached the power supply. It worked perfectly. Thanks so much for your service and instruction help.

Dryer wouldn't start.

  • Customer: Linda from Panama City, FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the video multiple times until I was comfortable. He made it look so easy. I'm convinced the dryer was using had been "prepped" to come apart and go back together easily. The reality for me: Great difficulty popping the cabinet top. It took every ounce of power to push in the hinges. Disconnecting the existing switch was difficult. I depressed in the catches on each side, but of course one at a time since I only have two hands. I tried various rigs to get both pushed in at once - nothing. Finally I watched a different vendor's video and the technique he used worked for me. Lastly, screwing in the new part is darn near impossible upside down to screw it in straight. The screws also wouldn't go in flush with the surface. I got them in well enough to hold, but that's it. The good news, the choice of part was correct and it fixed the problem. Had it now, I would have gone to Plan B and ordered a different part and paid another $9 shipping on top of the part. In my next life, I'm going to marry a appliance repairman.

door switch broken, wouldn't allow tub to stop turning when door opened.

  • Customer: Janet C from Manzanita, OR
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Exactly as described in the video provided online. Couldn't have been easier to do. All businesses should supply their customers with this kind of repair option!

Dryer wouldn't turn on.

  • Customer: Barbara from Lake Mary, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
According to your site, we purchased the Door Switch and the Thermal Fuse as these two parts had the highest percent of "what could be wrong". Figured we would send one back if we didn't use it. The Door Switch was replaced first and the dryer worked! Two days later, the dryer stopped working again. Still had the Thermal Fuse so we changed that out. The dryer worked again! Both parts arrived sooner than excepted! Both parts were simple to replace! The diagrams were very handy. The picture of the parts assisted greatly and the video's were the icing on the cake! VERY glad that we ordered both! Will recommend to everyone! PartSelect is bookmarked should we ever need your assistance in the future!

Broken Dyrer Door Cut-off Switch

  • Customer: Russell from Pflugerville, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
We bought a slightly used dryer, which kept running when the door was open. Trying to get the lid off, I broke one of the clips that held the top on. I gave up, and went to the internet. PartSelect made it easy to find my model and a list of all of the parts. They also had an on-line video that showed me the location of the secret screws that I couldn't find that led me to breaking the clip. After watching the video, the job was insanely easy! I was also surprised that their web site estimated the delivery of the parts at 1.8 days. I figured that this was an average, but the parts actually showed up at my door 1.8 days after I ordered them!

Remove old and install new door switch.

  • Customer: Newton from Lauder Hills, FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I watched your video online. And followed those instructions. It made it very intuitive and practical to follow. Believe me I am a novice but you made me feel like I am a professional.Thanks.

door switch

  • Customer: John from Austin, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Easy, screw driver (flathead) popped up two clamps on each side of top. maybe 3" from each side. Propped lid up with I think I used a full roll of paper towels, part was inside top left, unscrewed old,used small hook tool to unplug old, put new checked to see if it worked and bang lower top pop in place.NOTE : I am pretty good with fixing little things like this.. PLease UNPLUG for safety first then take time and be happy when you save $ on doing it yourself.

Door Switch broke

  • Customer: MONICA from DUBLIN, GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I pulled up the "How To" on the internet and it gave me step by step instructions. I only had to deal with 4 screws. Yaaayy! It was a good experience and the piece was perfect.
All Instructions for the RED4440SQ0
1,366-1,380 of 1,927