RED4100SQ0 Roper Dryer - Instructions

Watched Video a couple of times,,, then took off the back Panel, located the sensors, removed the Heater Coil to examine, for any breaks, looked OK, then replaces the 2 Sensors in the Thermal Cut-Off Kit, Finally Cut off and replace 2 Terminals needed to adapt wiring. Re-installed back Panel. Overall, took about an Hour Oh, it "worked" Dryer repair was successful

Popped the left and right side clips that hold the top, took out left and right side screws that held front face on, disconnected the wire that went to the door, tilted the door to me and lifted up from tabs on bottom. The old belt was broke, so it was easy to get off. Put the new belt on the drum making sure that the rubber ribs were touching the drum then I put the belt on the tensioner pully and motor pully. I rotated the drum by hand at least 1 full revolution to make sure that the belt was on right and it wasn't twisted, then I put everything back together. Easy 10 minute job... Art

Went on YouTube ,saw a video on how to diagnose and disassemble the dryer. Surprised how easy it was. I figured an appliance repairman would charge 100-150 so I would be wasting anything if I tried it myself.

I watched the installation video. It was exactly as shown.

Extremely easy! you can do this too. Just watch the video and have the few basic tools the video suggests. I am not skilled in repair at all. This part was shipped very fast and everything I needed was on the site. The hardest part was cleaning up the lint, seriously. Don't spend $100+ for a repair person to come to your home. This task is simple for anyone, any skill level.

unplug unit ,remove back cover six screws, slide off two wires on thermal fuse, remove one screw remove and replace fuse, reattach wires replace back cover

Our make/model was not on the online instruction, but it was similar. Ours had a glass (plastic)front window in the door. To remove the top catch you had to take out the top four screws that hold the door together (philips head screws) allowing you to pull back the gray plastic strip to access the top latch, then replace it like in the online directions using a needle nose pliers. The bottom catch, once the two remaining the screws were out gives you access to the bottom catch. Remove it with the pliers and snap the new ones into place. You can completely take out the window when you replace the bottom latch if you want.

My dryer all of a sudden stopped tumbling. When I opened up the machine, it turns out that the drive belt was broken. I simply put in the model number in PartSelect.com and found this kit that came with the belt, and drum rollers. The belt fixed the tumbling issue, and after replacing the rollers, the machine is as quite as a mouse! The instructional video helped show me exactly what to do and expect. This was my first time fixing an appliance, and it only took me 45 minutes!

Just pulled the old parts out on door latch and put the new ones in. Thanks Parts Select for your prompt response and easy process for order and shipment.

I had my laptop next to me and paused the tutorial video
as I did each step to chnage the drum rollers, idler pully and belt. Dryer runs great with no more screeching!

I followed video instructions. Raised the top, slipped off the front, installed the belt, aligned, installed tension part, reinstalled front, lowered the top and inserted lint trap. Job done. Quick and easy. The video was the key to the whole project.

Was shipped a new heating element and I installed it. The ordered new heating element was delivered in two days! I followed the instructions that came with the element and installed it in about 8 minutes. Piece of cake!

This was my first dryer repair. The only difficulty I had was figuring out how the belt tensioner was set up with the belt. The old belt broke so I didn't know how it was suppose to work. Anyway, it took a few minute to figure out that one end of the bracket was a "spring" that allowed it to flex a long ways! Pretty easy job.

Easy to follow videos on your site made this repair a breeze. I ended up having to replace the high temp cutoff as well but for 60 bux my dryer works like new. The repair man wanted $100 just to come look at it. Could not have done of without the easy to follow video.

ordered the part recived the parts and installed the part that easy. saved us lots of money did not have to buy a new dryer.