Models > REC3622BL0

REC3622BL0 Roper Dryer - Overview

Get Parts and Repair Help for REC3622BL0

If you know the dryer repair part you need, you can browse the list of all parts on the REC3622BL0, or you can search by name or part description. You can also find your part by where it is located on the REC3622BL0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for REC3622BL0 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the REC3622BL0 [Viewing 3 of 3]

$12.52

Thermal Fuse

This part is a one-time use thermal fuse which attaches to the blower wheel housing of your clothes dryer. It cannot be re-set and must be replaced when continuity between the pins...

$4.06

Door Catch Kit

This dryer door latch kit comes with one plastic door latch and one metal door strike.

$11.73

Idler Pulley Assembly

This part provides the tension required for a multi-ribbed belt. It also serves to help the belt to rotate the drum. This arm is what attaches to the idler pulley wheel.

$17.15

Drum Support Rollers

These two drum support rollers are no longer available for individual sale. Available in a package of two and it is recommended that you replace both rollers at once. These two rollers come with four tri-rings.

$85.42

Drive Motor with Pulley

This motor fits most Whirlpool incorporated dryer brands before 1996. NOTE: Pulley is NOT available separately.

$4.70

Heating Element Connection Wire Kit

This kit is used for electric clothes dryers, and it comes with a yellow wire nut.

$29.50

Lint Filter

This kidney shaped lint filter screen has a solid bottom with no cover.

$3.82

Tri Ring

Sold individually.

$3.71

Dryer Door Switch Actuator Spring/Lever

This black actuator spring with white rubber tip is used for both dryer doors and washer lids.

$30.18

Lint Filter Cover

This cover is used on kidney-shaped lint filters with no hole located inside the drum.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dryer was working, but no heat.

  • Customer: ANTHONY from CHESHIRE CT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 1071 of 1229 people found this instruction helpful
First I unplugged the dryer, then removed the back panel, this exposed most all of the wiring and I could see the heater coils.
Not knowing what the problem was I started looking at the coils and could not see any broken parts.
So then checked the thermal fuse for continuity I removed the two wires from it with a small pair of needle nose pliers, ... read more

No heat but would run otherwise

  • Customer: Dana from Grassvally CA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 503 of 514 people found this instruction helpful
Cleaning the lint out of the whole machine took quite a bit of time--it was everywhere. Underneath the lint trap was a collection that ultimately ruined the thermal fuse where it restricted the air flow considerably.

Ascertaining the problem was the most time consuming part.

The actual repair was quite simple and didn't take but 15-20 m... read more

Door Catch part had fallen out,/ was missing

  • Customer: Terri from Saint Augustine FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 493 of 496 people found this instruction helpful
Received your parts, Popped them both right into place, Even though only one side needed to be replaced, I wanted them to match up. It was amazing how easy this was. My husband was quite impressed I had ordered these rather then look for either a new or used dryer from some other source. read more