RC8700EDB0 Whirlpool Cooktop - Instructions

The element plugged in to the cook- top.The cook -top was working moments after i unpacked the element. thank you.

Jim B.

Changing the socket with a new one simply required removing one screw and splicing the two existing wires to the pigtails on the new socket. It took longer to unpack the replacement part than actually doing the job.

First, I removed the two screws holding the element in place. I removed the element from the connector. I then removed the trim ring and drip pan. I unscrewed the retaining screw holding the connector and pulled out the connector about three inches and disconnected the two wires leading to from the old connector. I removed the old connector. I then connected the two wires leading from the new connector and fasten the connector to its retainer with a screw . I reinserted the drip pan and trim ring and plugged the new element into the connector. I turned on control knob to high and tested the element., which glowed red hot. Job completed and customer very well satisfied..

removed 4 screws holding burner controls. removed wires off old and placed on new burner control. very pleased with quick shippig of part. two days and range was as good as new. excellent company to buy from

The repair was easy but the replacement coil had 4 connections while the old one had only two. After calling the distributor with no explanation of how to solve the problem I was given a telephone number of Jenn Air. They explained that my unit was too old and they no longer provided the part I needed.
I then decided to do the following. Of the 4 connections on the replacement coil, two are larger and two are smaller. I then decided to connect the wires to the two larger connections leaving the small ones free. I replaced the cooktop and WOW it worked. Not sure what the smaller connectors are used for but with old cooktops it seems they are not needed.
I can submit a photo but have no means to do it here

Problem was the neutral connector spike was burned and didn’t make good connection. Service man said he couldn’t get parts and charged $100 and left.
The neutral conductor cost about $12. And was an easy fix!

Thank you PartSelect!

Took the (6) screws holding the top of the stove out, then removed the switch screws(2). Then lifted the top, so as I could reach and get at the switch. And then I repeated the above. It was alot easier the second time. Duh I erred the first time and replaced the wrong one and before I relized it, I opened the switch to check out. All in all. I still got satisfaction from doing it myself. Thanks Parts Select

It would have been nice if basic instructions were supplied ( eg. how to remove switch panel ) but it went rather smoothly.
First killed power the electric stove.
I then removed the screws from the bottom of the panel and then pried the top of the control panel down and then out. I copied the positioning and wire colors.Removed wires from prongs, removed the two screws, replaced old switch with new one .

First I turned off the circuit breaker at the control panel to my Jenn-Air stove-top. At 220-volts, don't take any chances with electricity!

Then I removed two screws that hold the burner switch panel in place and lifted up the panel to expose the wires that are connected to all 4 of the burner switches, the exhaust fan and pilot lights that indicate if a burner is turned on.

I used a circuit tester to determine that the power was indeed off to the switches. Again, it is extremely important to respect 220-volts of electricity.

I ensured that all of the wires were already labeled the same as the terminal connections on the switch (i.e. H-1, H-2, P, etc.). If they are not, label them yourself with masking tape around each wire. Then I removed each of the wires connected to the burned out switch with a pair of needle-nose pliers.

Next I removed the two screws attaching the burner switch to the panel.

To install the new switch, repeat all of these directions in reverse, making sure to attach each labeled wire to the correct terminal on the burner switch.

Turn the circuit back on at the circuit breaker. Then test the burner switch and see if the burner heats up. Hopefully, you'll be cooking in no time...............

blower wheel was caked with dried grease clumps; replaced blower wheel, urethan foam and 3 motor isolators; blower/fan no longer vibrating cooktop.

I removed the 4 screws that held on the front panel as well as the knob of the defective switch. With the panel free, I pulled the wire connections from the rear of the switch with needle-nose pliers. I then removed the 2 screws which secured the switch and removed it. I then reversed the process with the new switch. It could not have been easier.

First I removed a screw that held the element in place then disconnected the two wires . Then I just reattached the two wires put the screw back in place and was done in about 10 minutes. Fairly easy fix, I had this go out a few years ago and had a repairman fix it, and saw how easy it was, so this time I did it myself. Easy job!!

Important to unplug the appliance first. There were two screws which were at the top opening of the oven. They were a bit obscure, but with a bit a searching, I was able to find them. After removing those two screws, the entire top lifted up. There were four screws from the bottom of that assembly which were easy to find, and once removed, the top lifted of easily. I found it easier to remove the two power lines with two easy disconnects, this made it easier to work on the assembly. The element itself was held down by two simple clamps which required no tools. There were four easy to remove wires, and the element came right off. Simply reversing the process put it right back together, plug it in, and back to cooking again.

Pulled out the burners, Freed the outside rim and removed the burnerbox with the burnned out pieces removed tham and reassembled

My grandson, age 15 did the replacement. Now, how easy is that!