Models > RC8400XBB2

RC8400XBB2 Whirlpool Cooktop - Overview

Get Parts and Repair Help for RC8400XBB2

If you know the cooktop repair part you need, you can browse the list of all parts on the RC8400XBB2, or you can search by name or part description. You can also find your part by where it is located on the RC8400XBB2 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your cooktop. We’ve also included any installation videos we have for RC8400XBB2 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the RC8400XBB2 [Viewing 1 of 1]

$8.22

Surface Burner Plug-In Block Kit

This newer-style terminal block kit includes two metal brackets, two pre-crimped wires with terminals, two ceramic wire nuts, a heat shrinking tube, and a mounting screw.

$26.93

Surface Burner - 8" - 2600W

NOTE: The manufacturer recommends that you replace the burner receptacle at the same time.

$24.60

Standard Y-Frame Surface Burner - 6" - 1500W

The manufacturer suggests replacing the receptacle at the same time.

$7.65

Drip Bowl - 6" - Black

Sold individually.

$8.61

8" Drip Bowl - Black

This black porcelain drip bowl with a hole in the bottom is intended for use with some electric ranges and cooktops.

$2.03

Screw with Washer

This metallic screw is less than an inch long and comes with a plastic washer.

$2.82

Surface Burner Stabilizer Clip Kit

This kit contains one clip, a screw, and a nut.

$3.82

Mounting Clip

This mounting clip is for the surface burner receptacle of your electric range. Sold individually.

$27.18

Surface Burner Knob

Sold individually. This knob accepts a double-flat shaft.

$23.34

Thermostat

Common Symptoms of the RC8400XBB2 [Viewing 1 of 1263]

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

8 inch burner wouldn't come on. Wires shorted out

  • Customer: Jonathan from Lilburn GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 36 of 43 people found this instruction helpful
One screw holds the block onto the stove top. Had to clean out fitting for phillips screwdriver or screw would have stripped because it was old with lots of buildup. Even cleaned out, this screw required great force with phillips screwdriver to keep from stripping. Caution! If you strip it, you'll have to drill it out! The rest was a snap. Cut the old wires ... read more

One burner didn't work all the time the other would go red hot

  • Customer: Phillip from Pekin IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 8 of 8 people found this instruction helpful
I unplugged the stove from the outlet, then removed the two burners I was going to be working on and the drip pans. Then I raised the top part of the stove and removed the screws holding the plug-in blocks to the stove. Then I cut the two wires going to the old plug-in block and stripped the wires back to match the new wire parts. Then I placed the sleeves o... read more

1 had 2 large burners not working at all, and was cooking everything on the 2 smaller burners

  • Customer: Mary from Lebanon CT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 6 of 8 people found this instruction helpful
It was so simple to repair - all I had to do was slide the older burners out and slide the new ones in - it took less than 10 min to complete the whole job! No tools used at all. read more