Models > RBS305PRS00 > Instructions

RBS305PRS00 Whirlpool Wall Oven - Instructions

All installation instructions for RBS305PRS00 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the wall oven repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RBS305PRS00
16-30 of 117
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broken Inner Door Glass

  • Customer: Ken from San Rafael, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 11 of 11 people found this instruction helpful
I removed the oven door by opening it to the horizontal position and inserting a small allen wrench in the open holes in each hinge. I then closed the door and lifted it free of the oven. I place the door face up on a packing blanket and removed the screws at the top of the door and the screws and clamps at the bottom of the door. I then lifted the outside glass door off the inner metal frame and set it in a safe place. I next removed the bracket holding the two inner pieces of glass and pulled the glass sheets out of the sheet metal holders. I then removed the screws which attached them to the metal door frame. Once the holders were off I removed the broken glass. I cleaned all the glass pieces and reversed the process to finish the repair.

Inside glass of the oven cooled too fast and cracked

  • Customer: Grant from Anaheim, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 12 of 15 people found this instruction helpful
The repair is straight forward. The only complication anyone seems to be having is removing the door ( which is a definate must to do this repair properly). So I would like to add some details about removing the door. The manuel shows the allen wrenches going into what looks like the hinge itself to release it from the oven. This is not the case. The holes that the 5/32 allen wrenches go into are actually behind the hinge itself. I wrapped the allen wrenches with some painter tape to protect the surface of the door and oven from scratching. Then, simply insert the short end of the allen wrenches, one on each side, into the holes behind the hinge. Then as it shows in the manuel, gently close the door. But not all the way. As you get about 80% closed you'll feel resistence. That is the time to grasp the bottom of the door and start to lift it from the bottom, while stablizing it with the other hand holding the handle on the door. The hinge will start to release from the oven as you continue to press it closer to being all the way closed. The hinges will release if you are doing this correctly before the door can be all the way closed.

Hope that helps. Otherwise, once the door is off. Unscrew all the screws...pay special attention to what you are unscrewing and how it all fits together, because you're going to have to put it all back together again. Some of the glass is held in place with clips and some of it is not. Just lay it down flat and be careful to not force anything in or out and you'll find it quite easy.

Upper oven bake and broil elements fail to heat when keypad entries made and indicating correctly

  • Customer: Kenneth V. from Kent, WA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 11 of 13 people found this instruction helpful
Replacement of the thermal overload safety thermostat very straight forward after sliding unit out, killing power and removing two covers. Tested both old and new and both show continuity (= good). Installed new, restored power and tested for proper operation. Didn't happen. Replaced original and now have new as spare. Now suspect the double line break relay on electronic control board is failed and source of problem. It is common to both elements and immediate before the suspected thermostat in circuit.

Bake element was broken. Oven would not shut down.

  • Customer: Lawrence from Atlanta, GA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 11 of 14 people found this instruction helpful
I used a cordless screwdriver to remove the retaing screws. One of the connections was pucshed back too far and was almost hidden in the hole. I used the tweezers to pull it out, replace the bake lelement and the retaining screws. I'm good to go!

Tempered Glass on oven door cracked; replaced the glass and insulation.

  • Customer: Leon from Atascadero, CA
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 11 of 15 people found this instruction helpful
I removed eight screws to disassemble the oven door. I removed the old insulation and the brackets that held class panel in place. I installed the new insulation, tempered glass and reassembled the oven door.

Oven would not heat

  • Customer: Elvin from Richmond, VA
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 10 of 13 people found this instruction helpful
This is a drop in range so I had to remove the range and set on a dolly. Turn the dolly around and acess the THRMST-FIX that needed replaceing, it was open. put the range back in its place and could still use the rest of stove until I received the parts 2 days later .
Pulled the range out put the new THRMST-FIX in put the range back together and put the range back in place and it has worked ever since.
GOOD JOB

lighting strike

  • Customer: Frank from Silverhill, AL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 11 of 16 people found this instruction helpful
replaced the suppressor and terminal block oven works

Double ovens and ONLY 3 oven racks.....

  • Customer: Paula from Fairview, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 9 of 11 people found this instruction helpful
No repair - just open the box and put the rack in my oven - voila - repaired!!! BUT let me tell you PartSelect sent the right part at the best price and I received it even ealier than I expected!!! I can DEFINITELY recommend these people and I do that very sparingly!!!! THANX!

Couldn't find correct light bulb anywhere!

  • Customer: Andrea from Redding, CT
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 11 of 18 people found this instruction helpful
I found the correct sized light bulb to fit the top portion of my double oven. It fit perfectly and just in time for Thanksgiving.
Thank you Part Select. It was easy to find the right size on your site and my order came in just a few days.

oven element

  • Customer: Eugene from Middleburg Heights, OH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 9 of 12 people found this instruction helpful
2 screws &2 push pull wires.

Bake oven element was not heating up

  • Customer: Sunil from Princeton Junction, NJ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 8 of 11 people found this instruction helpful
With little reluctance..I decided to change the part myself..but was very satisfied...with two screws to detach the bake oven and install the new one.I was very happy to receive the replacement part within 24 hours of placing the order with Part select.

oven door gasket seal worn

  • Customer: Kevin from Sterling Heigths, MI
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 7 of 9 people found this instruction helpful
Open oven dooor. With a philip screw driver remove the gasket plate at the bottom of the oven holding the seal gasket. pull seal gasket away from oven seal channel and clean surface before installing new seal. align seal pins to to seal channel holes be sure not to twist the seal insert pins in one at a time.Install lower bracket however you may want to wet the fray ends of the seal gasket prior to screwing in plate to keep the ends from moving away from the bracket when scrwing it in place.

Inner glass to oven door shattered

  • Customer: Robert from Forsyth, MO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 5 of 5 people found this instruction helpful
Removed the 6 screws securing the door and inner frame unit. Lifted off the frame and inner glass unit. Then, after cleaning all the broken glass, put the new glass in; first reattaching the inner frame and then the outer door cover.

Broken inner door glass on wall oven

  • Customer: Ronald from Scottsdale, AZ
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 5 of 5 people found this instruction helpful
The inner glass on the wall oven shattered (apparently a common problem). Rather than look at a new $2-3,000 oven, I found the part for around $30. The repair was actually fairly easy, just had to be careful with the glass panes.
I did not remove the door completely, just worked on it either open or closed, depending on the step. First I loosened the two screws on the bottom of the door (when closed). Then I removed the four screws on the inside of the door and the two on the top part of the door (2). This allowed the outer panel to slide out and be removed.
Then there are two middle panes, held on by small clips with two screws in each. Remove one at a time, being careful not to drop any of the glass on the floor! Remember the order of the glass and the clips, so you can replace in the same order. (Now's a good time to clean all of the inner panes also, and to vacuum out the interior of the door.)
Lay these panes aside, and you should be to the broken inner pane, held on by a metal panel--again remove a couple screws, the panel, and remove all the broken glass. Be careful to retain all the insulation around the glass, and replace the glass, then the metal panel, the inner panes, and the outer door panel in that order. The outer panel should slide into place if you remove one clip and screw and start on one side, then replace the clip.

Loose terminal caused block to overheat and break

  • Customer: Dana from Black Mountain, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 6 of 9 people found this instruction helpful
Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.
All Instructions for the RBS305PRS00
16-30 of 117