RBS305PDQ6 Whirlpool Wall Oven - Instructions

Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.

The other comments from folks who had done this were very helpful!
I had to go look up the directions for removing the door. To do this flip the latches on the hinges and then close the door as far as you can and pull up, it will come out.
Now lay the door flat on the kitchen counter and take out the 6 screws you can see on the edges and inside of the door. They are all the same so you don't have to keep them organized. Now you can take off the outer door with the handle (lift the inner door out since you will have the door face down at this point) and get it out if the way. Remove the hinges and set them aside but don't get them mixed up.
Next, take out the screws on the inner glass rails, there are two rails. Keep those rails in order for replacement. Take out the middle glass and clean it (this took oven cleaner and a razor blade on the one I had).
Take the middle of the door apart and expose the soft gasket (don't move it!). Clean out any broken glass and Insert your new glass. Put the middle piece of the door back on and line up all the screw holes! Put the first of the glass rails back on and the cleaned middle glass back in place, then the second glass rail. Put in the two screws that hold the glass rails.
Now you are ready to put the door back together. USE THE BOX TO HOLD THE DOOR OFF THE COUNTER WHILE YOU PUT THE HINGES BACK IN AND PUT THE DOOR FRONT BACK ON! If the screw holes don't all line up start the screws and work your way around, you'll get them to go in.
Voila! Door fixed.

I am not the handiest guy around so i was a little nervous doing this job but figured i would take a crack at it ( no pun intended). Took the door off as per instructions from kitchenaid , unscrewed all the outer screws , took off the back of door unscrewed the metal bar holding the glass in ( there are 3 levels of glass) took the 2 good glass sheets out got to the broken glass removed that put the new one in , replaced all the other glass and screws and put door back on, and i felt so proud. Probably saved about 150 dollars by doing it myself. I feel so proud.

Scarey> First thing you should do is cut off the electricity at the main breaker box. I dam near blowed myself up. It's 220Volt I found out after all hell blew up in my face. I was lucky and didn't get shocked.I shorted out the old broiler element.

So I made the job real easy I called a professional to come install the new broiler element.

I suggest you put a big red paper in each box that says turn off the power first. If your not sure how to do that call a pro.

My husband took the back off and replaced it. The repairman suggested pulling the range out into the floor to run the self clean mode. I have owned several such ranges and have never had to do that and won't now. Easy Clean Oven Cleaner will be the next thing I use.

This was more difficult than anticipated - probably because I'd never done it before. Once I got the door off (I didn't have the proper pins and used nails but didn't realize they had to be headless) I found all the screws, which were relatively easy to take out. I was surprised that the thermal door glass was obscured by two other panes of glass. It took more disassembly than anticipated and a few false starts when reassembling, but all in all it got done. I was happy that a job that would have cost probably $300 or more ended up getting done for $40 plus my labor - which isn't worth much these days. I'd certaily do it again.

Read all the way through this once before doing it. It really helps in keeping pieces and parts separated. First I had to take off the oven door. Please do this as it will make your life so much easier! The owners instructions does a lousy job explaining how to do this. You need to insert a small Allen wrench into the holes behind the door hinge pin. Just stick them in there and leave them. If you don't have Allen wrenches you can use small nails or the like, but you have to put something into the holes. Close the door slowly, yes it will feel like you are going to break the hinges or the wrenches. When you get the door almost completely closed you should wiggle the door a bit by the handle and pull up. The door will come off. Once you get the door off you can get to work. Leave these wrenches in the hinge holes. You will need a flat surface big enough to lay the door down to work on it. Lay it down with the handle towards the surface and the broken glass facing you. Remove the 4 screws on the broken glass side, the 2 screws holding the brackets on the bottom and the 2 screws on the top of the door. You will need to wiggle the inside cover off because there are 2 little clips at the top you need to get it off of the outer glass door. You should have 2 separate pieces, the outer glass of the door and the inner tempered glass and sheet metal portion of the door. Set the outer glass door aside, somewhere safe, as you really don't want to have to reorder that part too! From there you can lay the door down with the broken inner door glass towards the work surface. Remove the screws and good pieces of glass and lay them down in the order you take them out. This helps putting them back together later. Keep the pieces together in sets so you know which set goes to each section. There should be 3 pieces of glass total in the assembly. You remove the screws and the 2 good pieces of glass. The inside door glass is accessible under a large piece of sheet metal held in place by little flanges cut into it. You can remove this sheet metal panel piece by wiggling it out away from under the hinges and away from the hinge end. There is a piece of insulation under there as well. Make sure you reseat it correctly when you put it all back together. If you don't it will stick out, and make things hard to line up. Pull the broken glass out, Put the new glass in and replace the sheet metal panel. At this point I would suggest putting the four screws you took out at the very beginning from the inside of the door back in. They keep the 2 hinge assemblies in place and they will be harder to line up if you don't. You need to work from the bottom side up but it's pretty easy to get the 4 screws back in. Don't be afraid to wiggle the pieces around so you can line up the holes. They need to line up so that the hinges line up back to the oven. Reverse how you took the other glass pieces out and put the door back together. Put the front glass piece back on and secure it in place with the bottom door brackets and screws and the top 2 screws. Lift the door unit back up by the handle and place it in the slots for the hinges exactly the way you removed it. You will feel it sort of catch when you pull the door open slowly. Remove the Allen wrenches and you are done.

After 22 years the oven stopped heating in the middle of a meal prep. The fault code was F3 oven temperature problem. I googled the codes and found PartSelect described the problem and the repair and part needed. I received the oven sensor part, then turned off the power, used a screwdriver to remove 2 screws (had to find the right size flat head screwdriver to fit the square holed screws and they were pretty baked on after 22 years of use), gently pulled the sensor and wiring through the back of the oven. I used a needle-nose plier to pull the plastic connector through the insulation, then unsnapped the connector, snapped in the new sensor connector and pushed it back through the oven wall. Pretty simple repair, took me longer to find the screw driver than the actual repair.
Thank you PartSelect for making it easy and saving me a repairman visit!

Cut the power. Undid the screws to the element. Popped off the old element replaced with new,put screws back in turned power back on and Shazam it was up and going

Followed a video. Followed instructions

I was able to remove the old element and planned it with what little time off that I could. This would have been maybe 20-30 minute repair at the most. HOWEVER! I was extremely irritated screws were not included? When I called to ask if they were missing they said they didn’t come with the element. Cost me a very annoying trip to the hardware store. Not sure if I missed it on the site that they don’t provide screws - would have been nice to know that before I started. Still scratching my head as to why screws wouldn’t be included? My old ones were as beat up as the element I replaced. I was so irritated I was looking for a spot to leave feedback. Product is fine. Shipping was fine. Sending these products out as they do? Zero stars on that.

It was a matter of swapping out the old door with new door. In all, it was a snap . Around 10 screws to take it apart and a few brackets to hold it all together.

Quickly

This oven probably was manufactured in the '60s when the house was built. The door doesn't just pull off like the newer models. These pins fit into small holes on the oven hinges. I inserted the pins and lifted the door to a 45 degree angle, before pulling the door completely off. Now that turned out to be the easy part. I then proceeded to completely dismantle the door. It actually has 4 glass layers which had to be cleaned individually. The hardest part of all was actually remembering how to put it back together again. I put the door back on just as I had removed it, then took out the pins, and I was finally done! This was not an easy project, BUT the results look great.

With just the removal of a few screws I was able to replace the glass with the side benefit of cleaning the outter glass that had gotten dirty over the years with use. This is a simple project that all can complete.