Models > RBD305PRS00 > Instructions

RBD305PRS00 Whirlpool Oven - Instructions

All installation instructions for RBD305PRS00 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the oven repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RBD305PRS00
31-45 of 117
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Replacing inner glass on oven door

  • Customer: Kel from Denver CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
The other comments from folks who had done this were very helpful!
I had to go look up the directions for removing the door. To do this flip the latches on the hinges and then close the door as far as you can and pull up, it will come out.
Now lay the door flat on the kitchen counter and take out the 6 screws you can see on the edges and inside of the door. They are all the same so you don't have to keep them organized. Now you can take off the outer door with the handle (lift the inner door out since you will have the door face down at this point) and get it out if the way. Remove the hinges and set them aside but don't get them mixed up.
Next, take out the screws on the inner glass rails, there are two rails. Keep those rails in order for replacement. Take out the middle glass and clean it (this took oven cleaner and a razor blade on the one I had).
Take the middle of the door apart and expose the soft gasket (don't move it!). Clean out any broken glass and Insert your new glass. Put the middle piece of the door back on and line up all the screw holes! Put the first of the glass rails back on and the cleaned middle glass back in place, then the second glass rail. Put in the two screws that hold the glass rails.
Now you are ready to put the door back together. USE THE BOX TO HOLD THE DOOR OFF THE COUNTER WHILE YOU PUT THE HINGES BACK IN AND PUT THE DOOR FRONT BACK ON! If the screw holes don't all line up start the screws and work your way around, you'll get them to go in.
Voila! Door fixed.

Upper oven bake and broil elements fail to heat when keypad entries made and indicating correctly

  • Customer: Kenneth V. from Kent WA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
Replacement of the thermal overload safety thermostat very straight forward after sliding unit out, killing power and removing two covers. Tested both old and new and both show continuity (= good). Installed new, restored power and tested for proper operation. Didn't happen. Replaced original and now have new as spare. Now suspect the double line break relay on electronic control board is failed and source of problem. It is common to both elements and immediate before the suspected thermostat in circuit.

I snapped a bolt on the main power terminal block when connecting the pigtail.

  • Customer: Frank from Palm Coast FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 3 of 4 people found this instruction helpful
Removed the small metal panel covering the main power terminal in back of the electric range. Removed the nuts holding the red, white and black electrical wires from the range using the appropriate socket (there will be two nuts on each bolt end). Removed the two screws holding the main power terminal block with appropriate screw driver. Connect the new main power terminal block to the range using the two screws. Reconnect the red, black and white electrical wires coming from the range using one nut for each wire. IMPORTANT: do no over tighten the nuts because the bolts could snap. Reconnect the pigtail and secure the small metal panel covering the main power panel.

Oven did not work & display was dead

  • Customer: Christy from Thornton CO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
Removed upper oven panel above oven door,removed back cover & replaced electonic control panel. Everything works again

Broken inside view glass

  • Customer: Michael from Costa Mesa CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
Removed 4 screws top and bottom of the outer door panel. Remove outer door, then the two inner panes of glass. You are then able to remove the broken inner glass. Carefully slide the new inner glass into place, being careful not to tear the insulation. Once new inner glass is in place carefully replace the two inner glass panes and secure the screws. Replace the outer door and the top and bottom screws and that's it!

Couldn't find correct light bulb anywhere!

  • Customer: Andrea from Redding CT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 8 people found this instruction helpful
I found the correct sized light bulb to fit the top portion of my double oven. It fit perfectly and just in time for Thanksgiving.
Thank you Part Select. It was easy to find the right size on your site and my order came in just a few days.

I broke the inside oven door glass while cleaning it

  • Customer: Guy from Little Rock AR
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 2 of 2 people found this instruction helpful
The exact part for this oven is no longer available. I purchased one hat was close in size, but larger than the original. Upper and lower brackets hold the glass in place, so length was not a problem but height was. I removed the upper brackets, re-shaped them with the vise, a hammer and metal shears. The glass would now sit inside the bracket where the screws also went. I had to be quite careful the screws did not shatter the new glass.

The hardest part was aligning the 4 holes for the top brackets. Since 2 holes were on one piece of the door, and 2 were on the other (holding the glass sandwiched between) precision was critical. Also the screw length was critical because the glass now sat in a area where it could come in contact with the screws. (I know - pictures would be most helpful, and I didn't take any.)

Using tape and lots of patience, I got the holes aligned. I covered the old holes inside the oven door with spare screws. I filed down the points of the sheet metal screws so that, if they contacted the glass, they would not be pointed.

Once everything was reassembled, I turned the oven on high for about 1/2 hour to ensure the heated metal and glass all played nicely together. We've had no problems in the month since the repair.

inner oven glass cracked

  • Customer: Bill from Sedalia CO
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 2 of 3 people found this instruction helpful
With just the removal of a few screws I was able to replace the glass with the side benefit of cleaning the outter glass that had gotten dirty over the years with use. This is a simple project that all can complete.

Taking the door apart.

  • Customer: R G from Orlando FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
This was more difficult than anticipated - probably because I'd never done it before. Once I got the door off (I didn't have the proper pins and used nails but didn't realize they had to be headless) I found all the screws, which were relatively easy to take out. I was surprised that the thermal door glass was obscured by two other panes of glass. It took more disassembly than anticipated and a few false starts when reassembling, but all in all it got done. I was happy that a job that would have cost probably $300 or more ended up getting done for $40 plus my labor - which isn't worth much these days. I'd certaily do it again.

Missing Retainer and screw

  • Customer: Jan from Edmond OK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 6 people found this instruction helpful
Simple - Removed oven door attached retainer with screw.Re attached door.

Whirlpool wanted three time the cost of the same parts The only shipping option was Fedex Overnight which was very costly.

Your prices are great "Parts Select".

Jan

every time I would try to do the self clean mode on my drop in range the thermostat blows. Last time it was still under warranty. I took the part number from the repair man's invoice to order the new part.

  • Customer: joyce from thomasville NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
My husband took the back off and replaced it. The repairman suggested pulling the range out into the floor to run the self clean mode. I have owned several such ranges and have never had to do that and won't now. Easy Clean Oven Cleaner will be the next thing I use.

Broken inner door glass

  • Customer: alvin from st. louis park MN
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Removed the door from the oven. Undid all the parts above the inner glass door. Installed the inner glass and reassembled the door. Reinstalled oven door.

Broken Inner Glass on Oven Door by a Grandmother Who Should Know Better!

  • Customer: Diane from Citrus Heights CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 2 of 4 people found this instruction helpful
After reading all the other entries, I decided that I could do this! My first hurdle was getting the oven door off the hinges. Mine were not like any of the others described. My son-in-law looked at them and couldn't figure them out. So, I found the original installation instructions and, lo and behold, they said to flip the lever (one finger operation) in each of the rectangular holes holding the door onto the oven and then lift up until the door comes off. I did it, and it did! Boy, is it heavy! From there I just followed everyone else's instruction about undoing the screws, washing the glass panels, lining up the screw holes to get it back together, etc. One thing that took me longer was that the steel panel needs to go back the way it came out, not flipped! When I washed the glass panel it held, I put it down wrong and then "installed" it backwards. Luckily, I have a double oven and looked at the other one to see what was holding up the re-assembly! I'm glad that one of the others mentioned that the glass on the "bottom", the one that broke, isn't held in my screws or steel plates -- nothing, so I wasn't surprised when I got to it and it was "floating" on the insulation. My white insulation was like a fine fiberglass and was easy to stuff back in around the rim of the new glass. Took me a little over one hour. So, no more wet rags on hot glass (you'd think after living 72 years that I would remember this!) The glass fit perfectly and my husband would have been proud of me -- that I tackled a job that he usually handled, and that I saved over $200 for a couple of hours of labor and travel time.

Cracked in oven door glass

  • Customer: Alan from Prairieville LA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 2 of 4 people found this instruction helpful
Read the instructions in installation manual to remove door. Kept removing screws. Was surprised to find two panes of glass between the inner glass and the outer glass. Cleaned all the glass (4) and the inside of the door. Looks brand new. Be careful with the insulation; be sure it is pushed back or it will show from the outside.

Inner glass dooe cracked due to thermal stress

  • Customer: ariel from tarzana CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 2 of 4 people found this instruction helpful
I removed the Oven door, unscrew 10 screws, open up the dor case, clean all glass levels, replace inner glass, reassembled the door, reinstalled the door to the appliance.
All Instructions for the RBD305PRS00
31-45 of 117