Models > RBD305PDB12 > Instructions

RBD305PDB12 Whirlpool Oven - Instructions

All installation instructions for RBD305PDB12 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the oven repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RBD305PDB12
16-30 of 125
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Scratches in Surface

  • Customer: Michelle from Richardson TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 7 of 9 people found this instruction helpful
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

Oven door stayed locked with oven light on.

  • Customer: Larry from Dacula GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 7 of 9 people found this instruction helpful
Problem : One of the door latch center spindle locking clips had sheared off when the door was slamed shut. The latch then lifts up causing the light switch stay on and latch to stay engaged.
Repair: REMOVE POWER TO STOVE
1/ To open the door slide your fingers or a bent tool right to left to slide the latch to open the door.
2/ Go to the bottom of the open door on both sides and remove the screws. Then lift the plastic covering strips away.
3/ Remove the screws on both outsides at the top of the removed tracks
4/ Now you can lift the front panel with the clock up and off.
5/ Remove the 3 plugs on the back of that panel .
6/ Remove the 2 screws just above the latch.
7/ Remove the latch assemby.

Reverse order to install new latch & door.

Tempered Glass on oven door cracked; replaced the glass and insulation.

  • Customer: Leon from Atascadero CA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 6 of 7 people found this instruction helpful
I removed eight screws to disassemble the oven door. I removed the old insulation and the brackets that held class panel in place. I installed the new insulation, tempered glass and reassembled the oven door.

Bake element was broken. Oven would not shut down.

  • Customer: Lawrence from Atlanta GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 6 of 8 people found this instruction helpful
I used a cordless screwdriver to remove the retaing screws. One of the connections was pucshed back too far and was almost hidden in the hole. I used the tweezers to pull it out, replace the bake lelement and the retaining screws. I'm good to go!

Inside glass of the oven cooled too fast and cracked

  • Customer: Grant from Anaheim CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 6 of 8 people found this instruction helpful
The repair is straight forward. The only complication anyone seems to be having is removing the door ( which is a definate must to do this repair properly). So I would like to add some details about removing the door. The manuel shows the allen wrenches going into what looks like the hinge itself to release it from the oven. This is not the case. The holes that the 5/32 allen wrenches go into are actually behind the hinge itself. I wrapped the allen wrenches with some painter tape to protect the surface of the door and oven from scratching. Then, simply insert the short end of the allen wrenches, one on each side, into the holes behind the hinge. Then as it shows in the manuel, gently close the door. But not all the way. As you get about 80% closed you'll feel resistence. That is the time to grasp the bottom of the door and start to lift it from the bottom, while stablizing it with the other hand holding the handle on the door. The hinge will start to release from the oven as you continue to press it closer to being all the way closed. The hinges will release if you are doing this correctly before the door can be all the way closed.

Hope that helps. Otherwise, once the door is off. Unscrew all the screws...pay special attention to what you are unscrewing and how it all fits together, because you're going to have to put it all back together again. Some of the glass is held in place with clips and some of it is not. Just lay it down flat and be careful to not force anything in or out and you'll find it quite easy.

Replaced our oven racks, becasue I (the husband) forgot to remove them before the "Self-Clean" process and they turned colors just as the instruction manual said they would !!

  • Customer: Kevin from Joliet IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 6 of 8 people found this instruction helpful
Easy, pulled out the old dis-colored racks and slid the new ones in. I was VERY happy with the quick receipt of my order. If I ever need parts again,this is where I will go

Bottom Oven Element Wasn't Working

  • Customer: Shannon from Carlsbad CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 5 of 6 people found this instruction helpful
It was easy to remove the old element. It only required the removal of two screws and pulling apart the electric connectors. It was just as simple to install the new one.

Oven door latch would self-activate the door-lock feature for all operatons making it impossible to use the oven

  • Customer: Anthony from Lambertville MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 6 of 10 people found this instruction helpful
My electric oven is a built-in. First I turned off power to the oven.

Then, I removed the oven door as instructed by Kitchenaid, next I removed the screws that held the concealing-sleeves on each side of the oven opening. Slid down the sleeves, loosened the exposed screws on each to allow the oven to slide out. Slid the oven out abut half way to expose the top. Removed the metal sheeting from top of oven to expose area where door latch assembly was secured. Removing the sheeting was made easier by removing the screws on each side of the control panel and lifting the panel out of the way.

The latch assembly is held in place by two screws through the front of the plastic venting. Identified the connections to appropriate points before I removed the wiring, removed wiring and attached to points on the new latch assembly.

Secured latch assembly to plastic vent, secured sheeting to top of oven, placed conrol panel back in place, pushed oven back and secured with screws.
Slid sleeves into position, secured with screws and replaced oven door.

Double ovens and ONLY 3 oven racks.....

  • Customer: Paula from Fairview TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 7 people found this instruction helpful
No repair - just open the box and put the rack in my oven - voila - repaired!!! BUT let me tell you PartSelect sent the right part at the best price and I received it even ealier than I expected!!! I can DEFINITELY recommend these people and I do that very sparingly!!!! THANX!

oven element

  • Customer: Eugene from Middleburg Heights OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 5 of 7 people found this instruction helpful
2 screws &2 push pull wires.

Loose terminal caused block to overheat and break

  • Customer: Dana from Black Mountain NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 5 of 8 people found this instruction helpful
Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.

Front oven glass was broken through an accident

  • Customer: Paul from Afton IA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 6 of 11 people found this instruction helpful
Removal of the broken glass was easy , and it looked like the new glass just slid back into place. Ordering of the glass was also easy, and it looked like it would work. But, when the glass arrived, it looked liked the new door was exactly 1/2 inch too wide and the handle was 1/2 each off too. There was no where that stated that the glass needs to go in from the bottom up. You must take off the door by lowering it all the way to the floor and lifting the hinges. (See the manual) Once it is off, remove the clips from the bottom. Then put the glass on. The handle has to be turned only one way. So, even though it looks like it could go either way, it doesn't. Turn it over to fit. It was easy once the door and the clips were removed.

Inner glass door cracked

  • Customer: Carmen from Redlands CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 4 of 6 people found this instruction helpful
Kept removing screws and pulled things out until I got to the inner glass.
Yep, clueless and never did this before.
Put everything back in the opposite order of taking it out. Wala it's fixed.
Repair people wanted over $300 for parts and labor. However, with Partselect I was able to fix it for under $50.00 Well worth it!
Carmen

Inner glass to oven door shattered

  • Customer: Robert from Forsyth MO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 3 of 3 people found this instruction helpful
Removed the 6 screws securing the door and inner frame unit. Lifted off the frame and inner glass unit. Then, after cleaning all the broken glass, put the new glass in; first reattaching the inner frame and then the outer door cover.

Broken inner door glass on wall oven

  • Customer: Ronald from Scottsdale AZ
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 3 of 3 people found this instruction helpful
The inner glass on the wall oven shattered (apparently a common problem). Rather than look at a new $2-3,000 oven, I found the part for around $30. The repair was actually fairly easy, just had to be careful with the glass panes.
I did not remove the door completely, just worked on it either open or closed, depending on the step. First I loosened the two screws on the bottom of the door (when closed). Then I removed the four screws on the inside of the door and the two on the top part of the door (2). This allowed the outer panel to slide out and be removed.
Then there are two middle panes, held on by small clips with two screws in each. Remove one at a time, being careful not to drop any of the glass on the floor! Remember the order of the glass and the clips, so you can replace in the same order. (Now's a good time to clean all of the inner panes also, and to vacuum out the interior of the door.)
Lay these panes aside, and you should be to the broken inner pane, held on by a metal panel--again remove a couple screws, the panel, and remove all the broken glass. Be careful to retain all the insulation around the glass, and replace the glass, then the metal panel, the inner panes, and the outer door panel in that order. The outer panel should slide into place if you remove one clip and screw and start on one side, then replace the clip.
All Instructions for the RBD305PDB12
16-30 of 125