Models > RBD275PDQ8 > Instructions

RBD275PDQ8 Whirlpool Oven - Instructions

All installation instructions for RBD275PDQ8 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the oven repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RBD275PDQ8
1-15 of 84
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Inner window glass cracked

  • Customer: Evan from Albuquerque NM
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 60 of 76 people found this instruction helpful
The first thing I did was to remove the oven door by releasing the two latches on the hinges (by hand). I then raised the door toward the vertical position and lifted up. The hinges slide out of the oven housing. I laid the door, inside face up on my island counter top. This ensures that none of the parts will fall when disassembling the door. Next I unscrewed the screws 4 top and bottom and four on the inside face. This releases the frame from the front housing. Lift the frame off the door, exposing the glass pieces. Lift off the broken inside glass and place the new piece in the glass retaining housing. Replace the outside frame and replace all screws. Take door back over to oven and slide hinge bottoms back into slots on oven. Rotate to horizontal position and flip latches back to locked position. Total time was about 10 minutes mainly because I was curious how the door was constructed and I poked around while it was disassembled.

No heat after cleaning oven

  • Customer: Frederick from St. Louis MO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 40 of 46 people found this instruction helpful
This built-in oven was slid out of it's space and set on a box. I removed the back cover with nut driver and located the safety overload device. removed nuts and used pliers to remove wires and replace them. The power must be off to do this repair.Replaced the cover and slid back into place. This could be a lot more difficult if your power cord or gas line is not long enough to make it out of your wall space. Or of your oven is attached well to the frame.

The circuit board shorted out

  • Customer: Bruce from Manassas VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 58 of 101 people found this instruction helpful
The biggest challenge was figuring out how the panel was removed. Once I got that done, it was a piece of cake, just make sure that the connectors go back on the same slots on the new circuit board.

I broke the Bake Element while cleaning the oven.

  • Customer: Daniel from Cheraw SC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 20 of 22 people found this instruction helpful
I removed the two screws that held the bake element in place. Next I removed the Bake Element. I had to unscrew the oven to go behind it because when one piece off of the element broke, it slide back behind the oven. I pushed the wire back thru the piece holes, connected the Element, and pushed the element with the wires back through the holes. I rescrewed the element in place and the oven. PartSelect helped me to save this year's Christmas.

Oven wouldn't heat after cleaning cycle

  • Customer: Devin from Platte City MO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 10 of 11 people found this instruction helpful
Turned power to oven off. Removed trim screws and trim. Removed screws that anchored oven in cabinet. Removed oven from cabinet. Removed back panel, tested thermal fuse. Determined it was defective, ordered new part and reversed procedures above to reinstall.

Scratches in Surface

  • Customer: Michelle from Richardson TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 10 of 12 people found this instruction helpful
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

Digital control panel went haywire.. Control would not function

  • Customer: Anthony from Charlottesville VA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 9 of 10 people found this instruction helpful
First I removed the two screws that hold the sensor element in place (from inside the oven). I then pulled the sensor out about three inches and disconnected the two wires, and connected the new sensor. Screwed the sensor back into the back oven wall..

There was some confusion with the repair tech who first thought I would have to pull the pven out and remove the sensor from the back so that increased the time for repair. After pulling the oven it was obvious that the repair could be made from the inside..
The repair Tech's diagnosis of the problem was correct a nd fast. Part cost $75 on line ($102 from dealer locally). Saved over $125 cost compared to local repair man's visti.and that is a low side guess. Repair tech was very communicative.

Oven would not heat

  • Customer: Elvin from Richmond VA
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 9 of 10 people found this instruction helpful
This is a drop in range so I had to remove the range and set on a dolly. Turn the dolly around and acess the THRMST-FIX that needed replaceing, it was open. put the range back in its place and could still use the rest of stove until I received the parts 2 days later .
Pulled the range out put the new THRMST-FIX in put the range back together and put the range back in place and it has worked ever since.
GOOD JOB

al 4 interior lights had burned out

  • Customer: Kimberlee from Rocklin CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 10 of 13 people found this instruction helpful
The glass caps that cover the bulbs screw out by hand. Then, it was just like changing any other light bulb. I put the caps back on, and magically, we could once again see our food cooking. We had asked other repair companies to replace the bulbs when we had other major work done, but they either didn't want to take the time to get a part number, or didn't want to get it for us. On the PartSelect website, it was easy for us to find and order, not to mention we saved at least $75.00 on the service call alone. Thanks PartSelect!

Bake Unit not heating properly

  • Customer: Dan from Madison MS
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 9 of 11 people found this instruction helpful
Turned the power to the oven off. Took two crews out. Disconnected the old unit, connected the new unit, put the two screws back in and tested the unit.

Bottom Oven Element Wasn't Working

  • Customer: Shannon from Carlsbad CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 8 of 9 people found this instruction helpful
It was easy to remove the old element. It only required the removal of two screws and pulling apart the electric connectors. It was just as simple to install the new one.

Bake element was broken. Oven would not shut down.

  • Customer: Lawrence from Atlanta GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 8 of 10 people found this instruction helpful
I used a cordless screwdriver to remove the retaing screws. One of the connections was pucshed back too far and was almost hidden in the hole. I used the tweezers to pull it out, replace the bake lelement and the retaining screws. I'm good to go!

oven element

  • Customer: Eugene from Middleburg Heights OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 7 of 9 people found this instruction helpful
2 screws &2 push pull wires.

Oven door stayed locked with oven light on.

  • Customer: Larry from Dacula GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 7 of 9 people found this instruction helpful
Problem : One of the door latch center spindle locking clips had sheared off when the door was slamed shut. The latch then lifts up causing the light switch stay on and latch to stay engaged.
Repair: REMOVE POWER TO STOVE
1/ To open the door slide your fingers or a bent tool right to left to slide the latch to open the door.
2/ Go to the bottom of the open door on both sides and remove the screws. Then lift the plastic covering strips away.
3/ Remove the screws on both outsides at the top of the removed tracks
4/ Now you can lift the front panel with the clock up and off.
5/ Remove the 3 plugs on the back of that panel .
6/ Remove the 2 screws just above the latch.
7/ Remove the latch assemby.

Reverse order to install new latch & door.

replace inner glass on oven door

  • Customer: Robert from Dunwoody GA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 6 of 10 people found this instruction helpful
Once I figured out to get the door off, the actual replacement went well.
remove door, using allen wrenches in the holes of the door
remove outer glass - two screws on top, four screws along sides of inside door, two brackets on the bottom
that revealed anothe sheet of glass- held into place by a metal flange at the top (3 screws) and two brackets at the bottom. Pay close attention to how they are mounted for reassembly. They are the same physical configuration, but mount differently to hold glass up from the surface below
That reveals another sheet of glass held into place by two "ears" at the top and a bracket at the bottom.
When that is removed, the next thing to come off is a metal housing on which the glass just removed was mounted. I elected to leave the door hinge springs in place, and slide the metal housing in and out of position. That reveals the glass which needed replacement.
There is some insulation around the glass, but under the metal housing. It came out when I slid the metal out, which moved it from its location, but I think I got it back ok...be sure that it does not sitck out around the glass when you reassemble everything. Put everything back in place, replace the door and remove the allen wrenches. Done. Parts select had the product, and sent it very quickly.
All Instructions for the RBD275PDQ8
1-15 of 84