Quick Question!

Have you ever purchased from PartSelect.com before?

Models > RBD245PRB04

RBD245PRB04 Whirlpool Wall Oven - Overview

Get Parts and Repair Help for RBD245PRB04

If you know the wall oven repair part you need, you can browse the list of all parts on the RBD245PRB04, or you can search by name or part description. You can also find your part by where it is located on the RBD245PRB04 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your wall oven. We’ve also included any installation videos we have for RBD245PRB04 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$3.02

Screw

This screw is sold individually.

$50.25

Bake Element

The bake element is located at the bottom of the oven and gives off heat in order to bake evenly. If you notice that the element is not heating up or is not cooking evenly, it could be because it is broken or burnt out. All you need for this simple repair is a small screwdriver. To complete this repair, you will need to first turn the oven off (or shut off the house circuit breaker), remove the two screws that are holding the old element in place, remove the two wires from the old part, and then connect them to the new part and screw back into place.

$39.09

Limit Thermostat

An oven thermostat is a switch that opens and closes in response to the temperature it senses. It is typically found in the control panel, where a liquid-filled temperature-sensing...

$66.80

Temperature Sensor

The temperature sensor measures the temperature inside the oven. If your oven is too hot, not heating evenly, is not heating enough when baking, or simply will not start, you could have a faulty temperature sensor. A faulty temperature sensor can be a fire risk. If your sensor is not working properly, you should look to replace it straight away. A failed oven sensor is most often responsible for F3 or F4 error messages on electronically-controlled ovens. Make sure you disconnect the power to your range before you start your repair.

$20.15

Light Bulb - 120-130V - 15W

This part is a light bulb that is 120-130 volts and 15 watts, and is used in conjunction with your range or wall oven. The function of this bulb is to illuminate the interior of th...

$50.17

Broil Element

This broil element is found on the roof of the oven.

$19.73

Terminal Block

This part is for oven ranges, it connects individual wires and protects the device from electrical surges, voltages, and current. With this part, the house power is connected to th...

$45.35

Inner Oven Door Glass

This is the inner most piece of glass.

$2.94

Screw

Sold individually.

$4.79

Screw

Sold individually.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

No heat after cleaning oven

  • Customer: Frederick from St. Louis, MO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 97 of 106 people found this instruction helpful
This built-in oven was slid out of it's space and set on a box. I removed the back cover with nut driver and located the safety overload device. removed nuts and used pliers to remove wires and replace them. The power must be off to do this repair.Replaced the cover and slid back into place. This could be a lot more difficult if your power cord or gas line ... read more

I broke the Bake Element while cleaning the oven.

  • Customer: Daniel from Cheraw, SC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 54 of 63 people found this instruction helpful
I removed the two screws that held the bake element in place. Next I removed the Bake Element. I had to unscrew the oven to go behind it because when one piece off of the element broke, it slide back behind the oven. I pushed the wire back thru the piece holes, connected the Element, and pushed the element with the wires back through the holes. I rescrewed t... read more

Oven wouldn't heat after cleaning cycle

  • Customer: Devin from Platte City, MO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 32 of 33 people found this instruction helpful
Turned power to oven off. Removed trim screws and trim. Removed screws that anchored oven in cabinet. Removed oven from cabinet. Removed back panel, tested thermal fuse. Determined it was defective, ordered new part and reversed procedures above to reinstall. read more