Models > RBD245PDB12 > Instructions

RBD245PDB12 Whirlpool Oven - Instructions

All installation instructions for RBD245PDB12 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the oven repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RBD245PDB12
1-15 of 77
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

No heat after cleaning oven

  • Customer: Frederick from St. Louis MO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 45 of 51 people found this instruction helpful
This built-in oven was slid out of it's space and set on a box. I removed the back cover with nut driver and located the safety overload device. removed nuts and used pliers to remove wires and replace them. The power must be off to do this repair.Replaced the cover and slid back into place. This could be a lot more difficult if your power cord or gas line is not long enough to make it out of your wall space. Or of your oven is attached well to the frame.

The circuit board shorted out

  • Customer: Bruce from Manassas VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 59 of 102 people found this instruction helpful
The biggest challenge was figuring out how the panel was removed. Once I got that done, it was a piece of cake, just make sure that the connectors go back on the same slots on the new circuit board.

I broke the Bake Element while cleaning the oven.

  • Customer: Daniel from Cheraw SC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 20 of 23 people found this instruction helpful
I removed the two screws that held the bake element in place. Next I removed the Bake Element. I had to unscrew the oven to go behind it because when one piece off of the element broke, it slide back behind the oven. I pushed the wire back thru the piece holes, connected the Element, and pushed the element with the wires back through the holes. I rescrewed the element in place and the oven. PartSelect helped me to save this year's Christmas.

Oven wouldn't heat after cleaning cycle

  • Customer: Devin from Platte City MO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 13 of 14 people found this instruction helpful
Turned power to oven off. Removed trim screws and trim. Removed screws that anchored oven in cabinet. Removed oven from cabinet. Removed back panel, tested thermal fuse. Determined it was defective, ordered new part and reversed procedures above to reinstall.

The original blower squirrel cage failed out balance.

  • Customer: Joseph from North Grosvenordale CT
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 12 of 13 people found this instruction helpful
Safety first , I shut off the circuit breaker . I removed the racks from inside the wall oven . I removed the the wall oven from the niche .Then removed the three sheet metal panels in the rear of the oven exposing the mounting screws that hold the blower down .I removed the wires from the blower motor and then the blower assembly ,then I removed the small duct affixed to the blower assembly by a single sheet metal screw and transferred it to the new blower assembly . I installed the adhesive backed foam strip that is a vibration dampener and reassembled in reverse order.Once the over was returned to its original position in the wall mounting I turned the breakers back on and tested the oven ...AAAAAAAAA++++++++++++ To be fair i must admit that I am not a novice at this 15 years of my working career revolved around HVAC and appliance repair ,still however a novice that is mechanically inclined can perform the same task in about 70 to 80 minutes as opposed to my 35 . That is all there is to it.

Scratches in Surface

  • Customer: Michelle from Richardson TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 10 of 12 people found this instruction helpful
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

al 4 interior lights had burned out

  • Customer: Kimberlee from Rocklin CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 10 of 13 people found this instruction helpful
The glass caps that cover the bulbs screw out by hand. Then, it was just like changing any other light bulb. I put the caps back on, and magically, we could once again see our food cooking. We had asked other repair companies to replace the bulbs when we had other major work done, but they either didn't want to take the time to get a part number, or didn't want to get it for us. On the PartSelect website, it was easy for us to find and order, not to mention we saved at least $75.00 on the service call alone. Thanks PartSelect!

Oven would not heat

  • Customer: Elvin from Richmond VA
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 9 of 10 people found this instruction helpful
This is a drop in range so I had to remove the range and set on a dolly. Turn the dolly around and acess the THRMST-FIX that needed replaceing, it was open. put the range back in its place and could still use the rest of stove until I received the parts 2 days later .
Pulled the range out put the new THRMST-FIX in put the range back together and put the range back in place and it has worked ever since.
GOOD JOB

Broken inner door glass

  • Customer: Elizabeth from Seattle WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 10 of 14 people found this instruction helpful
I removed all the screws attaching the inner liner to the door, then removed the broken glass. I did this before ordering the replacement glass so I could be sure that only one piece was broken -- the door contains four pieces of glass in all. After the replacement glass arrived (really fast delivery!), I cleaned all the parts and reassembled the door. I had some difficulty in aligning the screw holes properly, and I'm still not sure if I have the exterior sheet of glass positioned correctly -- the schematic shows the order in which the parts go together but not how they fit exactly. I should have inspected the door more closely before I took it apart. Anyway, it feels solid and everything seems to work.

Inner glass

  • Customer: Michael from Denville NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 11 of 17 people found this instruction helpful
Take door off completely by setting hinge locks into place and then removing door. Take all of the screws out from frame (remember that the flat screws go the outside and the raised heads on the inside of door)Remove the clips on the bottom of door as well. Carefully remove frame. Then remove the inner glass clips, this will allow you to remove the broke or cracked glass easily and install the new glass. Set the door on a soft towel with finish side down. Make sure your hinges are on the proper sides if you moved them. (you will see where the screw hole matches up with the bottom of the frame. Do everything in reverse to put back together. Good Luck

Bottom Oven Element Wasn't Working

  • Customer: Shannon from Carlsbad CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 8 of 9 people found this instruction helpful
It was easy to remove the old element. It only required the removal of two screws and pulling apart the electric connectors. It was just as simple to install the new one.

Bake Unit not heating properly

  • Customer: Dan from Madison MS
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 9 of 12 people found this instruction helpful
Turned the power to the oven off. Took two crews out. Disconnected the old unit, connected the new unit, put the two screws back in and tested the unit.

Bake element was broken. Oven would not shut down.

  • Customer: Lawrence from Atlanta GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 8 of 10 people found this instruction helpful
I used a cordless screwdriver to remove the retaing screws. One of the connections was pucshed back too far and was almost hidden in the hole. I used the tweezers to pull it out, replace the bake lelement and the retaining screws. I'm good to go!

Oven door stayed locked with oven light on.

  • Customer: Larry from Dacula GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 7 of 9 people found this instruction helpful
Problem : One of the door latch center spindle locking clips had sheared off when the door was slamed shut. The latch then lifts up causing the light switch stay on and latch to stay engaged.
Repair: REMOVE POWER TO STOVE
1/ To open the door slide your fingers or a bent tool right to left to slide the latch to open the door.
2/ Go to the bottom of the open door on both sides and remove the screws. Then lift the plastic covering strips away.
3/ Remove the screws on both outsides at the top of the removed tracks
4/ Now you can lift the front panel with the clock up and off.
5/ Remove the 3 plugs on the back of that panel .
6/ Remove the 2 screws just above the latch.
7/ Remove the latch assemby.

Reverse order to install new latch & door.

oven element

  • Customer: Eugene from Middleburg Heights OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 7 of 9 people found this instruction helpful
2 screws &2 push pull wires.
All Instructions for the RBD245PDB12
1-15 of 77