Models > RB757WH1WW > Instructions

RB757WH1WW Hotpoint Range - Instructions

All installation instructions for RB757WH1WW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RB757WH1WW
46-60 of 239
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Easier than cookig a TV dinner.

  • Customer: Robert from olive branch MS
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 3 of 3 people found this instruction helpful
UNPLUG the oven. Following what every else was doing, I removed the element first, then disconnected the contacts. The leads on the contacts are not overly long, so I found myself removing cover on rear of oven when reconnecting red and yellow wires. Required removing two more screws with nut driver. Should I have to replace another element, I would remove rear cover first, unplug wires from element, remove element. Reverse procedure with new element.
While waiting for new element, be careful when turning on stove top element. Don't turn on oven by mistake, and when you do it, turn it off as fast as you can.
If you use stove top while waiting for part, don't forget to UNPLUG the oven. Won't be but a day or two. Very happy customer.

Burner terminal block unstable due to corrosion; potential electrical fire hazard

  • Customer: James from Tarpon Springs FL
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver
  • 3 of 3 people found this instruction helpful
This appeared to be an easy fix, but turned out to be more involved than I planned. The hard part was pulling the range/microwave oven assembly away from the wall so I could remove the back panel and see how the new terminal block wires connected up to the switch/knob that operates the burner. Extracting the whole range unit required me to use a floor jack to raise the leveling feet of the range above the edge of my floor tile so I could slide the unit out. Once away from the wall, I used a nut driver to remove the back panels. Next surprise was the new terminal block wire connectors were not the same type as the old block's connectors (flat vs. male pin-type). Rather than let the scope of this job creep to include a whole new connector rig, I opted to splice the new terminal block wires onto the existing wires that led up to the control knob. I used professional splices and a crimping tool to secure the wires. After checking the new installation was sound and operational, I slid the whole range back into place. Attaching the new terminal block to the range top was a piece of cake, but getting the damn oven out into open space where I could work on it was bear. But, hey, I learned a few things, one of which is that when a homeowner decides to retile their kitchen, make sure you run the new tiles all the way under the range and not just up to the front edge of the oven. I can see why this was done - to avoid having to remove the oven during the retiling - but it creates an obstacle for whenever the oven needs to be pulled away from its location. The last tool I imagined I would need for this repair was a car jack. The Parts Select part worked fine.

Needed extra oven space

  • Customer: noreen from flushing NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 9 people found this instruction helpful
Thanksgiving was coming and I needed extra oven space. So I ordered an additional rack. Installation ... just put it in the oven. My part came the day after I ordered it.

change broiler element

  • Customer: lee from bethel CT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 3 of 4 people found this instruction helpful
removed 2 1/4in. drill screws holding broiler element to oven removed 2 1/4in.drill screws holding broiler element to top of oven removed female spade connectors ffom old element and reversed assembley very easy

wire burned on surface terminal block

  • Customer: KATHY from SOUTH FULTON TN
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 3 of 4 people found this instruction helpful
I am a 62 y/o single female and was able to make this exchange of parts with ease. The toughest was getting the old terminal's wire clips free from years of gunk! I was pleased with the ease of installation and that it really worked afterwards. By the way, thank you Parts Select for getting this part to me very quickly. If a novice can diagnose, find the correct part and install it with success then anyone could do the same.

The broiler element wouldn't work.

  • Customer: Lajuanna from O'Fallon IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 3 of 4 people found this instruction helpful
After I ordered a new element unit, I read the "do it yourself" review on the page. I took the back off of the range and found the broken wire. I found that I had the same problem with the wiring, and that maybe the element was not the problem. I went to Lowe's and purchased a female spade connector, because no one would sell me one through the parts department. All I did was cut off the wire at the end of the burned section, stripped back about 1/2 inch of the wire and put on the new spade connector. I took off the origonal connector/crimp, and slipped on the new one. (You do have to make sure that the wiring doesn't touch the range back) The element was not the problem, so the origonal one still works fine. I may keep the element I ordered, just to have it if this one goes out. I didn't even need to remove the screws from the element inside the oven. It can all be done from the back of the range.

the bake element broke

  • Customer: Daniel from Apex NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
First I removed the 2 screws and removed the bake element, replaced the new one

lens snapped off on the inside-plug was left loose

  • Customer: RICKEY from MONTROSE NY
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 5 people found this instruction helpful
popped out the remainder of old lens, then pushed in new ones and slipped on plugs.

Front Large Most Powerful Burner's Block had broken so it didn't heat

  • Customer: Martin from plainfield CT
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers
  • 2 of 2 people found this instruction helpful
This electric stove has a lift up top which I lifted to get at the block and follow the wire back to the terminal at the back of the the stove. I removed the 5 small lag screws holding the back in place, removed the backing followed the wires back to where they connected in the Stove On/Off Control, disconnected the two wires from the control and then laid the new part in place rethreading and reconnecting the wires. I reinstalled the block and ran a test to ensure the burner operated correctly. After successful testing I disconnect the old block holder by removing the small lag screw, replace it with a new one that came with the replacement terminal block. I then inserted the block into the new holder carefully rolled up the excess wire and wrapped it in a couple of places with electrical tape and also secured it to the side of the stove, out of the way of operation with electrical tape, put the top down, plugged it back in and put it back in place. All told the repair took about 40 minutes. I was impressed with the speed of delivery, the quality of the product, the instructions for installation and the added bonus of getting a terminal block holder as part of the repair kit! Thank You for making me look like a genius!

Burned ou element

  • Customer: Buddy from Georgetown IN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 3 of 5 people found this instruction helpful
Removed two screws, and replaced element with a new one. Easy, works great.

Broiler not working

  • Customer: Teresa M from denver CO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 3 of 5 people found this instruction helpful
Turned off electricity. Removed two screws that held the element in back of oven. Removed the two screws that held it up to top of oven. Disconnected the two wires that held it in the rear of the oven. Removed it from the top support. Replaced the old element with the new in the support. plugged it it, replaced all four screws. Turned on the electricity and turned on the oven-it worked!

Part looked alike but did not fit

  • Customer: Klaus from Truckee CA
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 3 of 5 people found this instruction helpful
The hinge mechanism in the back of the range top, could not be fitted to the new part. I needed to enlarge a couple of seat holes on the underside in the front portion of the new part to make it seat securely enough so the hinge mechanism could be safely deleted. (The new top is now simply sitting on the range, without hinge in the back).
More care should have been used to identify the correct top for the exact model and serial number of the range. Even though I had communicated those numbers when I ordered the part, and the picture looked like the correct part, the problem arose.

a pan was dropped on hot bake element,,bake element broke

  • Customer: fran from harrisburg PA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 2 of 2 people found this instruction helpful
i dd not notice at first and started the self cleaner,,,i notice the self cleaner did not work,the screws had to be sprayed with dw30a couple of times and a pair of pliers to remove screws(no wrench set)after removing screws pulled the wires out to see and removed the connection to wires,,,replaced with new bake element and replaced the screws works fine,,,by the way i am a 64 years old grandmother

burner not work

  • Customer: SILVIA from Midlothian TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
Fue muy facil desconectar primero la estufa despues quite los tornillos de la parte superior detras de la estufa, desconecte un cable del switch y lo conecte en el nuevo despues el siguiente hasta conectar todos los cables en el nuevo switch. Lo mejor es desconectar uno por uno para mo mesclar los cables , despues removi el switch de la estufa y puse el nuevo , puse las partes de regreso y listo conecte la estufa t revise si funcionava el quemador y listo sin ningun problema.

Cleaning oven latch engaged while pizza was cooking

  • Customer: Jeffery from Victor ID
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 2 of 3 people found this instruction helpful
In a panicked state, my roommates and I could not turn the cleaning setting off. So, we "Jerry-rigged" the door open to save the house from the awful burning pizza smell and potential fire. We removed the stove top with the nutdriver only held in with three nuts. Removed the insulation promptly after. Disassembled the latch mechanism with the star wrench set. The scariest part of the replacement was looking confused at the new part. To our dismay, the part looked grossly under sized. we thought it would not fit. After placing the part in place of the broken latch we found the replacement fit better than the previous and was a totally painless success. Do-it-yourself, not that complex and an excellent way to save money.

_Jeffrey B.
All Instructions for the RB757WH1WW
46-60 of 239