All Installation Instructions for Hotpoint Range RB757WH1WW

temperature sensor went

Took back panel off unplugged sensor and replugged in and worked like a charm!Sears wanted $400 and was going to 'overrepair"Got the 60 dollar part on here. UPS shipped to wrong address and customer service refunded my shipping and was excellent! would definetly use again!thanks

Parts Used:

Temperature Sensor Kit

Alex R from Randoff, NJ
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

Was this instruction helpful to you?

Thank you for voting!

The burner combusted burning the the burner switch

Disconnected the appliacnce from the power source. Using screwdriver, removed the back panel and disconnected every wire that are connected to the switch. Pulled out the front nob and removed the switch. Then install the new switch by screwing it back in. Place all wires back and back panel. Connect and finish.

Parts Used:

Surface Burner Switch - 8 Inch - 2500W

Felipe from Donna, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Old surface burner terminal block stopped working

Disconnected the electric burner from the terminal block, unscrewed the terminal block, removed the two back covers from the range, cut the two wires (since the wires that came with the replacement part were not long enough to reach the switch), spliced the new part to the existing wiring using wire nuts, installed the new terminal block and connected the electric burner to it. With the new terminal block in place, the burner does not lie completely flat like the old one did, but it is functional.

Parts Used:

Surface Burner Terminal Block Kit

William from Severna Park, MD
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Trim has tendancy to rust on range oven door

Unscrewed bottom screws, replaced trim. No trouble.

Parts Used:

Bottom Trim - White

Carole from San Diego, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Bake Element Broke

followed the instruction from your video an it was a snap

Parts Used:

Bake Element - Push On Terminals - 240V

Lesley from LaPlace, LA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers

Was this instruction helpful to you?

Thank you for voting!

Disgusting looking burner drip bowls.

Just had to change out the drip bowls, easy. But, I wanted to comment on the quick delivery on the new bowls. I was impressed. Thank you.

Parts Used:

Drip Bowl - 8 Inch

Drip Bowl - 6 Inch

Constance L from Woodhull, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

none

Took the old pans out and put the new ones in. Simple as pie

Parts Used:

Drip Bowl - 8 Inch

Drip Bowl - 6 Inch

Leslie N from Carson City, NV
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

Burner not getting hot

replace element

Parts Used:

Surface Burner Terminal Block Kit

Janice from Paterson, NJ
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Blew the electronic Control Board

It was easy to replace it. Just remove the screws and unplug each wire and plug them back. The problem was to take off the plate cover that has the printed letters on. The plate cover cost more than the Electronic Control Board.

Parts Used:

CONTROL OVEN TO9

PETE from MANCHACA, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Rusted oven door trim

Removed old part by removing the screws at the boottom of the oven door. I wasn't sure if the glass oven door cover would remain in place once the trim piece was removed, fortunately I was ready when it came down. The glass cover is large and heavy so you need to be ready to handle the bulk of this piece once the last screw is removed. Cleaned everything and with the help of my wife, who secured the oven door cover in place, secured the new trim piece by replacing the screws. What a difference, looks like new! PartSelect provided great service in terms of speed and part acciracy.

Parts Used:

Bottom Trim - White

Todd from Pittsburgh, PA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver

Was this instruction helpful to you?

Thank you for voting!

Burner was always on high when on.

Disconnected the power. Removed hex head screws from top and lower rear panel. I think there were 8 all together. Pull the knob of the burner control, removed two screws that held the switch in place. Moved the wires one at a time to the new switch, re-assembled. Burner worked properly. Very easy to find the right part from this web-site, and the instructions from others like this were helpful. Easy fix!

Parts Used:

Surface Burner Switch - 8 Inch - 2500W

David from Jericho, VT
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Burner light would not shut off

Checked each burner switch by disconnecting the light indicator wire. Located the switch, replaced the switch and the indicator light operated as it should.

Parts Used:

Surface Burner Switch - 8 Inch - 2500W