Quick Question!

Have you ever purchased from PartSelect.com before?

Models > RB757BC4WH

RB757BC4WH Hotpoint Range - Overview

Get Parts and Repair Help for RB757BC4WH

If you know the range repair part you need, you can browse the list of all parts on the RB757BC4WH, or you can search by name or part description. You can also find your part by where it is located on the RB757BC4WH by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. We’ve also included any installation videos we have for RB757BC4WH parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the RB757BC4WH

[Viewing 3 of 3]
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$3.88

Light Bulb - 40W

This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these repla...

$68.62

Bake Element - Push On Terminals - 240V

The bake element is located on the bottom of the oven. If your oven will not heat properly it may be due to a faulty or damaged baking element. If you can see that the element has been separated or blistered, you should replace the part immediately. If there is no visible damage, turn the oven on and check to see if the element heats evenly. If the element is not heating evenly, or if it is not heating at all, it will need to be replaced. This element is 19 inches wide x 19 inches long, and has male spade push on terminals.

$7.25

Burner Bowl - 8"

This part is located beneath the element and catches any spills.

$6.36

Burner Bowl - 6"

$13.33

Surface Burner Terminal Block Kit

This kit includes the female contact with wires, terminal block and mounting clip.

$22.98

Surface Burner Switch - 8" - 2500W

$14.40

Surface Burner Terminal Block Kit

Also known as receptacle.

$43.91

Oven Rack

The oven rack is sold individually. It is chrome in color and measures approximately 24 inches wide by 17-1/2 inches deep. The rack is used to hold cookware in the oven and slides back and forth for easy access. Racks can become rough and discolored over time and may need to be replaced, or perhaps you just need extra storage space in the oven! This repair is extremely simple and does not require any tools. Before you begin, ensure that the rack edges are straight and have not warped from shipment. Once the oven door is open, the stop end goes in first and it simply slides into place.

$46.81

Surface Burner Element - 8"

This Y-frame eight inch surface burner element has five turns and a metallic center medallion.

$26.32

Surface Burner Switch - 6" - 1560W

This switch controls the small burner on a range/stove top.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Lower bake Element would not heat.

  • Customer: Ronald from Nassau, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 178 of 188 people found this instruction helpful
First I slid the stove out and unpluged it, then removed two screws,slid out element, disconected two wires, slid new element in to place, pluged two wires in ,put into place and installed two screws, pluged stove back in, and turned on to try. Works perfect. read more

The Bake-o-lite (Hard Plastic) block that holds the burners female connection in place had chipped away over time and wouldn't allow the male part of the burner to connect up correctly.

  • Customer: Robert from Mt. Vernon, IN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 102 of 104 people found this instruction helpful
After unplugging the range I took the rear sheet metal panel at the top off with a nut driver to expose the wiring connections. The next step was to remove the single screw holding the old part in place. (under the drip pan) Once free I snipped the old part from the wires and then taped the new female ends to the old wires with black electrical tape. From re... read more

The switches failed on both front burners.

  • Customer: Marc from Columbia, NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 69 of 73 people found this instruction helpful
Remove nobs from both switches.
Pull out the range (the hardest part).
REMOVE THE POWER PLUG FROM THE WALL
Remove 7 screws with nut driver and take off upper back panel.
Remove 2 phillips screws from front, they hold the switch brackets.
The new switches don't fit in the bracket so discard the bracket keeping the screws.
Removin... read more