Quick Question!

Have you ever purchased from PartSelect.com before?

Models > RB756GT5WW

RB756GT5WW Hotpoint Range - Overview

Get Parts and Repair Help for RB756GT5WW

If you know the range repair part you need, you can browse the list of all parts on the RB756GT5WW, or you can search by name or part description. You can also find your part by where it is located on the RB756GT5WW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. We’ve also included any installation videos we have for RB756GT5WW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$7.42

Drip Bowl - 6"

This drip bowl, also known as the drip pan and burner bowl, is 6 inches in diameter and is used to catch spills from cooking on the top burner. If your bowls are getting stained, d...

$9.43

Drip Bowl - 8"

This drip bowl is sold individually. It is chrome in color and measures 10 inches in diameter at the widest point, with a hole in the middle. This is used to catch drippings and food that falls when cooking on the oven element. These might burn, become rusty, and wear down over time, and will need to be replaced. Replacing the drip pan is very easy. The elements on the oven must be removed to access the pan underneath. When placing the new bowl, make sure to line up the hole with the terminal block where the element plugs into.

$37.57

Bake Element

At the floor of your electric oven is the bake element. This partially open-style element comes with push-on terminals. The bake element will likely provide most of the heat for ba...

$36.66

Surface Element - 8" - 2350W

The surface element, also known as the coil surface element, transfers heat to the area on top of range. The element is 8 inches in diameter. If your surface element does not heat, over heats, or heats inconsistently, replacing this part can be the solution to your issue. To determine whether the element is defective, use a multimeter to test it. Before installing the new element, make sure the drip bowl is properly aligned with the notch of the pan. Insert the new element into the reciprocal at a 40 degree angle. Refer to the instructions provided by the manufacturer for more guidance.

$27.16

Surface Element - 6" - 240V

If you notice that your surface element will not heat properly, you may need to replace it. This surface element is 6 inches in diameter and 240V. It is a Y-frame surface burner el...

$5.30

Single Heating Element Support Clip

The metallic clip, or also known as a broil element support, is for a oven element on a range. This part holds the broil element in place on top of the oven. If your support clip is broken then this replacement should be the solution. The tools needed for this project are slip joint pliers. For safety precautions, make sure to unplug your range from the power source, or shut off the house circuit breaker before starting this project. Refer to the installation instructions for best results and accuracy.

$18.39

Oven Light Housing

The light housing is also known as a lamp holder and is a part for the oven in your range. The function of this piece is to hold the bulb that will light up the inside of your oven...

$103.92

Oven Sensor

It is possible that your oven is cold because of a fault in the temperature sensor. The temperature sensor regulates oven temperature in modern ranges, like a thermostat. It is on the back wall near the broiler on the top wall. On a newer oven, there may be a fault code displayed. Faulty temperature sensors are often responsible for F3 and F4 error messages on an electric range. Check your manual or the manufacturer website to find out the proper resistance of the temperature sensor. To check your sensor, unplug the oven and use a multi-meter to see if your sensor is at the correct resistance.

$4.56

Oven Bulb Lens Cover - Glass

$54.02

Surface Burner Terminal Block Kit

This is a surface burner terminal block kit, also known as range surface element receptacle, for an oven, range, or stove. The kit comes with the terminal block, mounting clip, and wires. This surface burner terminal block kit connects the wiring harness to the surface elements. It is important to shut off the power to the appliance before starting this repair. You will need to remove all four elements, trim rings, and drip bowls to access the terminal block on your stovetop. This is an OEM replacement part that is sourced from the genuine manufacturer.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Bake element cracked on its own

  • Customer: Timothy from Cordova, TN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 589 of 594 people found this instruction helpful
Flipped the breaker. Removed shelf, Find the right size nut socket, unscrew the two screws, pull the element out a little bit, disconnect the wires (on pretty tight), pull out element, clean out any mess in the oven, compare element with new one to make sure its the same size and such, connect wires to new element, replace screws, flip breaker back, tur... read more

I needed new surface elements & burner bowls

  • Customer: John from San Ramon, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 481 of 488 people found this instruction helpful
This was about the simplest fix I've ever done. Just pulled off the old surface elements & burner bowls, wiped down the range top, and put in the new parts. Perfect fit. No problems at all. $$ well spent. ParsSelect shipped quickly, and they arrived well packaged. A+ experience all around. Thanks PartSelect. JA, San Ramon, CA read more

Burner bowls needed replacement

  • Customer: Tom from North Prairie, WI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 472 of 478 people found this instruction helpful
Very easy repair, Pulled burner coil out, removed old burner bowl. Put in new burner bowl, plugged burner coil back in... easy as 1,2,3 read more