Models > RB747G*J1 > Instructions

RB747G*J1 Hotpoint Oven - Instructions

All installation instructions for RB747G*J1 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the oven repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RB747G*J1
1-15 of 430
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

element quit working

  • Customer: Wilbur from Taylorville IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 464 of 464 people found this instruction helpful
Unhooked electrical wiring from unit and rehooked new unit to electrical wiring.

Bottom heating element went out

  • Customer: Michael from Saint Paris OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 369 of 373 people found this instruction helpful
This repair took between 15 and 30 minutes BUT ONLY because my 10 year old son did the repair. He couldn't wait for his father to come home from work. His only complaint was the tight fit to reach the back of the oven (he wanted to take the oven door off but I said no). He removed the 2 screws that held the element in place and then pulled it from the oven until he could remove the screws that held the wires in place. He was concerned that a little of the insulation came out with the wires, but this was no issue. The new element hooked right up (we figured out that we had to use the 2 new screws for the wires because the old ones did not fit very well). We used the same 'old' screws to attach the element back to the oven. Plugged the oven back in and it works fine. My son was so proud and I didn't have to help any more than shining a flashlight for him.

Oven heating element was broken.

  • Customer: Phyllis from Fisk MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 256 of 329 people found this instruction helpful
The heating element in the lower oven of my 18 year-old GE double oven broke into two pieces and would not heat. Because of the age of the oven, a replacement part was unavailable through GE. I came across PartSelect.com through an Internet search and ordered the part online. Total cost was $33.50, counting s/h. FedEx delivered the new element less than 48 hours after I placed the order online.

IMPORTANT: FLIP the BREAKER to stop electricity from going to the oven. Replacing the heating element is a two step process: 1. Remove the old element. 2. Install the new element in its place. (NOTE: This job is much simpler if you lift and remove the oven door BEFORE you begin. NOTE also: There are no slots in the screws, so you must use a small socket wrench--not a screwdriver-- to remove the screws.) STEP 1: Two screws go through the small metal plate attached to the element prongs. These screws hold the element to the back oven wall. Remove the screws, then pull the element forward a few inches to gain access to two screws which hold the element prongs to wires that come through the back oven wall. (One wire and one screw for each of the two prongs.) Remove the two screws. Remove and discard the old element. STEP 2: Install the new element by doing Step 1 in reverse. Oven is now repaired! (It took more time to type these instruction than it took to repair the oven.)

The oven element had broken in half and was sparking

  • Customer: Brittany from Cayce SC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 113 of 176 people found this instruction helpful
I am not a handy person so I was really nervous about doing this. I first unplugged the oven just to be on the safe side. Then I removed the two screws that hold the element in place. Next I pulled the element forward and disconnected the two wires. After that I simply reconnected the two wires to the new element, pushed it back in and put the screws in. Piece of cake!

oven would no longer heat. Only broiler worked

  • Customer: Liz from Williamson NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 90 of 152 people found this instruction helpful
First I removed the 2 screws that held the bake element in place. Then I pulled the element out and disconnected the two wires. Reconnected the two wires to the new element and pushed it back in place and installed the unit again with the 2 screws. Turned the oven on and it heated up like it should.

Replacement of Coils

  • Customer: Joseph from South Plainfield NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 31 of 37 people found this instruction helpful
Removed by slightly wiggling out of the coupling. No tools needed, seriously, (and I'm a contractor). Basically, pull out and snap back in.

Electronic Timer went out and Top Oven No Longer worked

  • Customer: David from Owings Mills MD
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 30 of 38 people found this instruction helpful
There are about 12 wires behind the panel...and this was the second time I've replaced the electronic clock in the past four years. I replaced the analog clock four years ago with the digital version because the analog was no longer available, so I knew what I was in for. There are four screw (top of the frame and lower frame) to remove before the frame holding the clock will come out. First DISCONNECT the power! You've have to remove the clock control knobs, and the plastic lever on the self cleaning handle. The first time I ordered this replacement part from PartsSelect there was a diagram included on which wire goes where. This time there wasn't! So it gets a little complicated. Make sure you label all the wired before you disconnect the old clock panel. Anyway, remove the four nuts holding the old clock in place; put the new clock panel in; replace the four nuts. I'll be glad to talk anyone through the rest and I have photos of the whole repair.

bake element bent down to bottom of oven (ready to break)

  • Customer: James from Tazewell VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 24 of 29 people found this instruction helpful
1) turned off breaker to oven
2) removed oven racks
3) removed screws holding old element
4) pulled out element far enough to remove 2 wires attached to old element
5) noted colors, left white, right black
6) attached new element to wires
7) attached new element to oven
8) put back oven racks
9) turn breaker back on
10) test oven
done

The bottom element had broken apart and needed to be replaced

  • Customer: Becky from Norman OK
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 18 of 20 people found this instruction helpful
The only reason I mentioned "a bit difficult" is that it is very important to unplug the unit first. I didn't want to say easy because I didn't want someone just jumping right in, (you do end up handling raw wires).
First I removed the two screws that were holding in the element to the back wall of the oven, then pulled out the old element slightly until you see where the wires are attached to the end of the element. I made note (I don't know if this is neccessary) which wire came off which screwset so I could put the new one in the same way. Took out the old element and attached the new one to the two screwsets on the ends of the element and then reinserted that part in in the back wall of the oven and attached plate that holds it in place. It was for my mother and she now thinks I'm a genius! Don't let anyone take a picture of you of you from behind because you definitely have to put your head in the oven. I believe the door is removable that may make it easier to get to it.

Element burned into.

  • Customer: Ward from Gilmer TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 15 of 16 people found this instruction helpful
First I removed the two screws that held the element in place. I pulled the element out about 2-3 inches and then removed the two screws that fastened to the ends of the element. Was careful to keep the same wires separate in order to fasten the new element back to the same two wires. When fastening the new element ends back to the wires, care must be taken to not bend the ends of the element when tightening the small screws to the ends. Everything went real good and am most pleased with the very fast service portrayed by Parts Select. They are a class act company and rate very high in customer satisfaction!

Mechanical/electrical clock/timer not working

  • Customer: Maxwell from RINGWOOD NJ
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 18 of 25 people found this instruction helpful
Followed the instruction provided except had to add a NEUTRAL LEAD which on the old part had been provided by the frame as it was metal/ electrical vs plastic/electronic . Used one of the extra Wire Extensions provided, drilled a hole in the clip connection and attached it to the metal frame holding in the replacement clock. The need for a NEUTRAL LEAD was not discussed in the instructions.

Old mechanical timer worn out.

  • Customer: Theodore from Atwater CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers
  • 14 of 17 people found this instruction helpful
This digital timer, GE Part # WB19X10006 (PartSelect PS233996) is called out by GE as the current replacement for the mechanical timer in the JB500G*J1 range. I had tried to get one some time ago from another dealer but was told it was discontinued and no longer available, so I was pretty happy to come across it in the PartSelect catalog.

It comes with a number of mounting brackets and instructions to use the brackets that resemble the old parts, but when I did that the control buttons did not line up with the holes in the glass and were offset about 1/4" to the left. It was impossible to simply slide the timer over that far because it bumped into the underlying metal frame. I ended up using a longer set of brackets which lifted the timer about 1/2" off the glass, thereby avoiding interference with the frame, and bent the brackets sideways to line up with the holes in the glass. But then a transformer on the new timer stuck out about 1/4" too far in back to get the rear cover back on. I made two vertical cuts in the rear cover from the edge down past the timer and bent the resulting flap around the transformer. The resulting installation looks like it was made that way and works great.

Heating element required continuous adjustments to work.

  • Customer: Richard from Apex NC
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 12 of 13 people found this instruction helpful
I removed old 8" surface element and terminal block. Some of old wiring had to be cut off because of harding/cracking of old wiring. Stove was 23 years old and this burner was the most frequently used one. I soldered the new and remaining old wires together. I used the shirnk wrap that came with the terminal block to cover the solder joint. I screwed the new terminal block (one screw holds it in place - used same screw from old terminal block that was removed). I finished by inserting the new surface element. Everything works fine. In the next week or two after we use it a while, I will check wiring again to make sure there are no changes. You need to be very careful as it gets very hot under the burner.

The bake element would not heat up.

  • Customer: Douglas from Derry NH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 11 of 11 people found this instruction helpful
This repair took much longer than it should have.
When I noticed the oven would not heat in bake mode, I suspected the element was bad. Going on the forum, I found that I needed to ohm out the element to be sure, so from inside the oven, I removed the two screws holding the element into the stove, pulled out the element a bit and removed the screws from each contact, ohmed it out and found no continuity. I ordered a new bake element which arrived in a couple of days.
I installed the new element by connecting the wires back to each terminal end. It still didn't work and not only that, the broil element didn't work now either.
I inquired again on the forum and found that the suspect might be the control module that controls both bake and broil elements. The part was $250.
Not wanting to spend that on a 10 year old stove, I ordered a new stove at Sears that was on sale.
I sent the bake element back and waited for my stove to arrive.
Sears called a few days later that my stove was ready for pickup so in preparation, I pulled my old stove out from the wall and began to disconnect the pigtail to use on the new one. It was then I noticed a wire dangling that seemed to go to one side of the bake element. When I pulled out the bake element initially and disconnected the wires, I didn't notice that one terminal had TWO wires going to it and one had a single wire connected. It was a bit dark inside the stove when I initially took the screw off of each terminal and I never noticed the second wire on the left one. I installed the old bake element, knowing it may not work but just to see if the broil now worked and it did!
So I ordered another bake element and installed it connecting two wires to the left terminal and one to the right terminal, reattached it to the back of the oven and IT WORKS!!

I cancelled my new stove at Sears which saved me about $500. Just a $26.00 part.

Bake Element burnt up

  • Customer: John from Lafayette LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 11 of 11 people found this instruction helpful
Turned off breaker to stove.Used nut driver to remove the holding plate from the back ove the oven. Their was between 4 to 6 inch of slack on the wire. Used the nut driver and removed the red wire from the right side of the old element, and then removed the white wire from the left side of the element. Replaced the cap head screws that required a nut driver, with the slotted screws that came with the new element, replaced the white wire(left) the red wire(right), end reattached the holding plate to the back of the oven and done!
There are stand offs on the bottom of the element, so you can't get it confused on where the wires go, but take care that the wires do not slip back in the element "hole" or you will have to "fish" them back out.

Brought the element up slowly to 500 degrees, to burn off any residue on the element. Smelled a chemical smell for the first 5-10 seconds of the "burn in", then no smell.
All Instructions for the RB747G*J1
1-15 of 430